WoodstockメーカーW1099の使用説明書/サービス説明書
ページ先へ移動 of 21
COPYRIGHT © BY WOODSTOCK INTERNATIONAL, INC. TX 4-085-998 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. REPRINTED FEBRUARY 1999, PRINTED IN TAIWAN DOVETAIL JIG W1099 OPERATING MANUAL P.
TABLE OF CONTENTS Woodstock Intl., Inc. W1099 I. INTRODUCTION ............................................................................................................................. 2 II. COMMENTARY ..............................................
I. INTRODUCTION - 2 - Woodstock Intl., Inc. W1099 II. COMMENTARY Woodstock International, Inc. is proud to offer the W1099 12" Dovetail Jig. Suitable for pro - duction work or small scale dovetai.
- 3 - Woodstock Intl., Inc. W1099 III. SAFETY RULES FOR ALL TOOLS 1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications and limitations, as well as its particular hazards. 2. KEEP ALL GUARDS IN PLACE and in working order.
IV. UNPACKING - 4 - Woodstock Intl., Inc. W1099 Remove the items packed in the carton. It may be a good idea to save the carton and packing material in case they might be needed in the future. Upon removal of all items from the package, you should have: 1.
- 5 - Woodstock Intl., Inc. W1099 Pin Depth The W1099 is designed to produce half-blind dovetail joints with a router, 7 / 16 " guide bushing, and 14°, 1 / 2 " dovetail router bit. Half-blind dove- tails are very strong and are commonly used in fine drawer construction.
- 6 - Woodstock Intl., Inc. W1099 VIII. ADJUSTMENT LOCATIONS 1. The hand levers clamp your workpiece in place. 2. The fence knobs hold the fence in place. Loosen these knobs to adjust fence position. Router travel is stopped when the router base contacts the fence.
- 7 - Woodstock Intl., Inc. W1099 The side stops serve three purposes: 1) they posi- tion each workpiece square to each other, 2) they offset the two workpieces for proper alignment, and 3) they give lateral support to the workpieces during routing. IMPORTANT: All pieces must be cut perfectly square for the jig to work properly.
- 8 - Woodstock Intl., Inc. W1099 4. Insert a drawer side under the front clamp. This piece will be vertical. Adjust the height so the end of the vertical board overlaps the end of the horizontal board. At this point it is not crucial that the pieces be flush.
- 9 - Woodstock Intl., Inc. W1099 XI. TEMPLATE ADJUSTMENT The template is adjustable from front to back so that the joint will be hidden when the dovetails are complete. Adjustment is made by loosening the two template lock knobs. Do not adjust the screws holding the template.
- 10 - Woodstock Intl., Inc. W1099 The fence controls the depth of the dovetail pins by limiting the distance that the router travels. The router stops when the router base hits the fence. The fence must be adjusted parallel to the edge of the vertical piece just like the template.
- 11 - Woodstock Intl., Inc. W1099 Your router base must accept a guide bushing with a 7 / 16 " outside diameter and an inside diameter large enough to accept a 1 / 4 " shank dovetail bit. Securely mount the guide bushing to your router. Refer to your router’s operating manual for further instructions.
- 12 - Woodstock Intl., Inc. W1099 Figure 13 shows dovetails after cutting. Figure 14 shows a finished drawer and 2 sides ready to be joined. Use care when the router bit exits the workpiece to reduce the risk of tear-out. See section XIV.A. for further instructions.
- 13 - Woodstock Intl., Inc. W1099 B. RABBETED DRAWER FRONTS Drawer fronts that have been rabbeted around the inside edge to create a lip to restrict drawer travel in the closed position require some additional setup. To produce half-blind dovetails on rabbeted draw - er fronts: 1.
- 14 - Woodstock Intl., Inc. W1099 XIV. TROUBLESHOOTING C. INCOMPLETE FIT An incomplete fit occurs when the side piece protrudes from the end of the front or back piece. Figure 17. Cause: The distance between the edge of the side piece and fence is set too narrow.
- 15 - Woodstock Intl., Inc. W1099 XIV. TROUBLESHOOTING E. FIT TOO TIGHT OR TOO LOOSE If you find the fit to be about right in every other aspect, but it is simply a little too tight or too loose, the depth of the router bit is probably mal - adjusted.
XV. WARRANTY - 16 - Woodstock Intl., Inc. W1099 LIMITED WARRANTY Woodstock International, Inc. (Woodstock) war- rants this product against defects in workmanship and materials under normal use and service for a period of one year. This warranty extends to the original purchaser from the date of purchase.
- 17 - Woodstock Intl., Inc. W1099 XVII. PARTS DIAGRAM.
- 18 - Woodstock Intl., Inc. W1099 XVIII. PARTS LIST XIX. TOOL DATA W1099 DOVETAIL JIG Overall Dimensions: Height .........................................................................................................................................
- 19 - Woodstock Intl., Inc. W1099 XX. INDEX A Address ............................................................... 1 Adjustment Locations ......................................... 5 Assembly ........................................................
- 20 - Woodstock Intl., Inc. W1099 NOTES.
デバイスWoodstock W1099の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Woodstock W1099をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWoodstock W1099の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Woodstock W1099の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Woodstock W1099で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Woodstock W1099を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWoodstock W1099の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Woodstock W1099に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWoodstock W1099デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。