WyseメーカーR class WES2009の使用説明書/サービス説明書
ページ先へ移動 of 26
Inst allation Guide Wyse ® R Class Conversion to WES2009 Wyse ® USB Firmware T ool TM Release 1.13 Products: R10L, R50L, R5 0LE, R90L, R90LE, R90L7 Issue: 09071 1 PN: 883887-29L Rev .
Copyright Notices © 201 1, Wyse T echnology Inc. All rights reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not rep roduce, transmit, transcribe, store i.
Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling Rx0L Flash and RAM 3 Requirements 3 Procedure.
iv Contents This page intentionally blank..
1 Introduction This guide provides the instructions you need to use W yse ® USB Firmware T ool t o convert the following Wyse R class thin clients to WES2009: •R 1 0 L • R50L • R50LE • R90L • R90LE • R90L7 Caution WES2009 firmware requires R class thin client s to have a minimum of 2 GB flash and 1 GB RAM.
2 Chapter 1 The Conversion Sof tware Assembly DVD-ROM contai ns: • A PDF of this Installation Guide • Wyse USB Firmware T ool v1.13 • RX0L_LE 2G_4G WES2009 Conversion Image folder containing the followi ng files: · bio s.img · cmos.img · commandsX ml.
2 Inst alling Rx0L Flash and RAM This chapter con tains information fo r users of Wys e Rx0L thin client s who must inst all new flash and/or RAM. If you ar e installing firmware only , you can skip this chapter and proceed to"Installing WES2009 Firmware.
4 Chapter 2 Procedures S tep 1: Remove the Rx0L Thin Client Left Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing Rx0L Flash and RAM 5 S tep 2: Install the Rx0L Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
6 Chapter 2 S tep 3: Install the Rx0L RAM Module Wa r n i n g RAM modules may be susceptible to damage by Electro-S ta tic Discharge (ESD). All industry-st andard cautions should be followed to avoid ESD.
3 Inst alling Rx0LE Flash and RAM This chapte r contains inform ation for u sers of Wyse Rx0LE thin clients who must install new flash and/or RAM. If you are installing fi rm ware only , you can skip this chapte r and proceed to"Installing WES2009 Firmware.
8 Chapter 3 Procedures S tep 1: Remove the Rx0LE Thin Client Left Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing Rx0LE Flash and RAM 9 S tep 2: Install the Rx0LE Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
10 Chapter 3 Figure 9 Removing the existing f lash module 3. Install the new flash module in th e reverse order of removing the original flash module. Carefully press the flash module onto the st an dof f lock and connector , making sure to lock it into place.
Installing Rx0LE Flash and RAM 11 S tep 3: Install the Rx0LE RAM Module Wa r n i n g RAM modules may be susceptible to damage by Electro-S ta tic Discharge (ESD).
12 Chapter 3 This page intentionally blank..
4 Inst alling WES2009 Firmware This chapter includes the requ irements and pr ocedures you need to inst all and use Wyse USB Firmware T ool to update your thin client to WES200 9 firmware. Tip The purpose of the Wyse USB Fir mware T ool is to configure a boot able USB key for device firmware.
14 Chapter 4 Procedures Complete the following procedures as an adm inistrator (administrator privileges are required). S tep 1: Copy the RX0L_LE 2G_4G WES2009 Conv ersion Image Folder to Y our Local .
Installing WES2 009 Firmware 15 Figure 12 Wyse USB Fir mware T ool wizard 2. Click Next to open the Select an Op tion dialog box. Figure 13 Configuration optio ns 3. Select the Configure a single USB key to Copy or Up date firmware option, and then click Next to open the Select t he Configuration dialog box.
16 Chapter 4 6. (Optional) Leave the default-sele cted Preserve data partition check box (recommended in most cases) unless you do not want to preserve any existing custom data partition you have on the th in client ( outside of the partition used by the firmware).
Installing WES2 009 Firmware 17 Figure 17 Prep are USB drive 12. Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The progress b ars show the ov erall (for matting and configurat ion) progr ess and task prog ress.
18 Chapter 4 S tep 5: V erifying Thin Client Operation After the thin client displays the WES2 009 desktop, you can verify the Ve r s i o n and that your general client information is correct.
Installing WES2 009 Firmware 19 Figure 19 Placement of labels on the R50LE and R90LE S tep 7: Obtain a Firmware Update After conv erting your thin clie nts, obt ain any availab le firmware upda te at http://www .wyse.com/serviceands upport/support/downloads.
20 Chapter 4 T roubleshooting This section contains ge neral troubleshooting information. USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing processes on U SB keys (and the variety o f them), not all brands have been tested with the Wyse USB Firmware T ool.
Installing WES2 009 Firmware 21 This page intentionally blank..
Inst allation Guide Wys e ® R Class Conversion to WES2 009 Issue: 0907 1 1 Written and publishe d by: Wyse T echnology Inc., September 201 1 Created using FrameMake r ® and Acrobat ®.
デバイスWyse R class WES2009の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wyse R class WES2009をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWyse R class WES2009の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wyse R class WES2009の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wyse R class WES2009で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wyse R class WES2009を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWyse R class WES2009の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wyse R class WES2009に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWyse R class WES2009デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。