WyseメーカーWES2009 4GFの使用説明書/サービス説明書
ページ先へ移動 of 22
Reference Guide Wyse ® R Class Conversion, XPe to WES2009 Wyse ® USB Firmware T ool TM Release 1.10 Issue: 102910 PN: 883887-16L Rev . C.
Copyright Notices © 2010, Wyse T echnology Inc. All rights reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not reproduce, transmit, transcribe, store in .
Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling R90L Thin Client Flash 3 Requirements 3 Proce.
iv Contents This page intentionally blank..
1 Introduction This guide pro vides step-b y-st ep instructions to convert R90L and R90LE thin client s from XPe to WES2009. Caution WES2009 firmware requires R class thin client s to have a minimum of 2GB flash. Note After conv erting your thin clie nts, ob tain any a vailable firmware update at http://www .
2 Chapter 1 The Conversion Sof tware Assembly DV D-ROM conta ins: • A PDF of this Reference Guide • Wyse USB Firmware T ool Release 1.10 • R Class WES Conversion Image folder cont aining the following files: · bios.img · cmos.img · commandsXml.
2 Inst alling R90L Thin Client Flash This chapter cont ains information for users of Wyse R90L thin client s who must install new flash. If you are installing firmw are only , you can skip this ch apter and proc eed to"Installing WES2009 Firmware.
4 Chapter 2 Procedures S tep 1: Remove the R90L Thin Client Lef t Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing R90L Thin Client Flash 5 S tep 2: Install the R90L Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
6 Chapter 2 This page intentionally blank..
3 Inst alling R90LE Thin Client Flash This chapte r contains inform ation for user s of Wyse R90LE thin clie nts who must inst all new flash. If you are installing firm ware only , you can skip this chapter and proceed to"Installing WES2 009 Firmware.
8 Chapter 3 Procedures S tep 1: Remove the R90LE Thin Client Lef t Side Cover Caution Follow all precautions listed in the Quick- S tart Guide that came with your thin client for disconne cting and reconnecting the thin client.
Installing R90LE Thin Client Flash 9 S tep 2: Install the R90LE Flash Module Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
10 Chapter 3 Figure 8 Removing the existing f lash module 3. Install the new flash module in th e reverse order of removing the original flash module. Carefully press the flash module onto the st an dof f lock and connector , making sure to lock it into place.
4 Inst alling WES2009 Firmware This chapter include s the requirements and procedures you nee d to install and use Wyse ® USB Firmware T ool TM to update your thin client to WE S2009 firmware.
12 Chapter 4 S tep 3: Use Wyse USB Firmware T ool to Configure a Single USB Key to Convert Firmware 1. Double-click the shortcu t to run the tool an d open the Wyse USB Firmware T ool wizar d (the welcome p age provides the product version and descriptio n, and a link to view the Wyse end user license agreemen t).
Installing WES2 009 Firmware 13 4. Select the Windows Embedded St andard OS type option. 5. Select the Up date Firmware operation to perform option. Note Although the Preserve dat a partition check bo.
14 Chapter 4 Figure 15 Prep are USB drive 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The pr ogress bar s show the Overall Progr ess and task progress.
Installing WES2 009 Firmware 15 S tep 5: V erifying Thin Client Operation After the thin client reboo ts, you can veri fy that the general client information is correct.
16 Chapter 4 S tep 6: Atta ch a Wyse Co nversion Label and Microsof t License Label on Each Converted Thin Client The conversion kit is suppl ied with Wyse Conversion Labels and Microsof t License Labels that must be att ached to each thin client as shown in Figure s 17 and 18.
Installing WES2 009 Firmware 17 T roubleshooting This section contains ge neral troubleshooting information. USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing processes on U SB keys (and the variety of them), not all brands have been tested with the Wyse USB Firmware T ool.
Reference Guide Wys e ® R Class Conversion, XPe to WES2009 Issue: 1029 10 Written and publishe d by: Wyse T echnology Inc., October 2010 Created using FrameMake r ® and Acrobat ®.
デバイスWyse WES2009 4GFの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wyse WES2009 4GFをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWyse WES2009 4GFの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wyse WES2009 4GFの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wyse WES2009 4GFで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wyse WES2009 4GFを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWyse WES2009 4GFの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wyse WES2009 4GFに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWyse WES2009 4GFデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。