XantechメーカーHD88Cの使用説明書/サービス説明書
ページ先へ移動 of 16
08905150B - 1 - INSTALLATION INSTRUCTIONS HD88CC5 HD88C High Definition Video Matrix Switcher, Coaxial and CAT5 High Definition Video Matrix Switcher, Coaxial Only DESCRIPTION The HD88CC5 eight-source.
08905150B - 2 - Safety Information CAUTION: TO REDUCE THE RISK OF ELECTRI C SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
08905150B - 3 - Damage Requiring Service — These appliances should be serviced by qualified service person nel when: • A power supply connection or a plug has be en dam aged or • If liquid has b.
08905150B - 4 - IMPORTANT NOTICE HD44 Series and HD88 Series INTRODUCTION In some installation scenarios, an audio/video source component (such as a cable box or DVD player) may fail to work properly with distribution pr oducts or even a display.
08905150B - 5 - DETAIL OVERVIEW FRONT PANEL The front panel is designed to provide the unit’s cu rrent Output/Input setting st atus. Note that only one Output/Input status setting is displayed at any given moment. The top row of LED indicators represents the current ZO NE output selection.
08905150B - 6 - REAR PANEL [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to pr ovide an output at the same level as the input – i.e. Unity Gain (assuming a 75-ohm termination is on the output). Use these connections for HD88 expansion systems.
08905150B - 7 - [4] RS232 (SERIAL) COMMANDS The RS232 Port is bi-directional. The communica tion parameters are se t to 9600 Baud 8-N-1. DB9 CONNECTOR CIRCUIT PIN TX 2 RX 3 GND 5 RS232 COMMAND STRUCTURE Where: { z# } - Zone Number. Range is 1..4 (1..16 if expanded) { s# } - Source Input Number.
08905150B - 8 - [5] RS232 EXPANSION The HD88C and HD88CC5 can be exp anded into larger systems. By using any combination of the HD88C and HD88CC5 (up to 4 units), a larger High- Definition distribution syst em can be created for up to 32 Zones of Component Video and Digital Audio Distribution.
08905150B - 9 - [7] IR BUS The IR_IN port utilizes a 3. 5mm mono jack. Use this port to connect to an IR emitter ou tput port of a Xantech connecting block. PLUG CIRCUIT TIP IR SIGNAL SLEEVE GROUND [8] CAT5 ZONE OUTPUT This is an Output connection to the HDRXSG01 rece iver module.
08905150B - 10 - QUICK INSTALLATION: HD88CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD88CC5 or HDTXSG01. Figure 1 below shows an HD88CC5 (video matrix transmitter) c onnected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD88CC5 zone output or the output from the HDTXSG01 to the HDRXSG01.
08905150B - 11 - RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “F1”. ZONE 1 2 3 4 5 6 7 8 1 Zone Selec tion 80 48 10 90 00 C0 50 D0 2 Source Selection 40 A0 30 B0 20 E0 70 F0 3 Zone Po.
08905150B - 12 - ADVANCE INSTALLATION Sports Bar The figure below shows a diagram for a sports bar application. With the equipment rack located near or behind the bar area, the coaxia l outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios and pool table recreational areas.
08905150B - 13 - Expanded System The figure below shows an expanded HD88CC5 (16 Z ones and up to 32 HD monitors) system. With two HD88CC5 devices, HD content can be distribut ed to 32 displays (16 with CAT5 outputs, 16 with coaxial outputs).
08905150B - 14 - Notes:.
08905150B - 15 - Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xa ntech”) warrants to the holder of a valid proof of purcha se as the first end-us.
08905150B - 16 - Xantech Corporation 13100 Telfair Avenue Sylmar, CA 91342 www.xantech.com Phone: (818) 362-0353, Fax: (818) 36 2-9506 Installation Instructions, HD88CC5, HD88C © 2009 Xantech Corporation This document is copy righ t protected.
デバイスXantech HD88Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Xantech HD88Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはXantech HD88Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Xantech HD88Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Xantech HD88Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Xantech HD88Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はXantech HD88Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Xantech HD88Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちXantech HD88Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。