XantrexメーカーPowerpack 300の使用説明書/サービス説明書
ページ先へ移動 of 61
by XP ower P owerpack 3 00 (Emergency P ower) Owner's Guide 975-0277-01-01 REV . A Printed in China t 1-360-925-5059 f 1-360-925-5143 www .xantrex.
by XPower Powerpack 300 Owner’s Guide.
About Xantrex Xantrex T echnology Inc. is a world-leading su pplier of advanced power electronics and controls with pro ducts from 50 watt mobile units to one MW utility-scale systems for wind, solar , ba tteries, fuel cells, microturbines, and backup power applicatio ns in bot h gri d-connected and stand-alone system s.
i About This Guide Purpose The purpose of this Owner ’ s Guide is to provide ex planations and procedures for installing, operating, maintaining, and troubleshooting th e XPower Powerpac k 300.
About T his Guide ii Conventions Used The following conv en tio ns are used in this guide. Abbreviations and Acronyms WA R N I N G W arnings identify conditio ns that could result in personal injury or loss of life. CA U TION Cautions identify conditio ns or practices that could resul t in damage to the unit or to other equipment.
iii Important Safety Instructions The XPower Powerpack 300 generates a type of AC power similar to a normal household wall outlet. Operating the XPower Powerpac k incorrectly or misus ing it may dam age the equipment or create hazardous conditions for the user .
Important Safety Information iv W ARNING: Explosion hazard Do not use this product where ther e are flammable fumes or gases, such as in the bilge of a gasolin e-powered boat, or near propane tanks. Do not use this product in an encl osure contain ing automotive-type l ead-acid batteries .
Important Safety Information v WAR N I N G : F i re h a za rd The jump-start feature is design ed for sh ort term operation only— less than 4 seconds. Operating the jump-start feat ure for more than 4 seconds may cause damage to the un it. Allo w the XPower Powerpack 300 to cool down for at least 3 mi nutes after each jump- start.
Important Safety Information vi Precautions W hen W orking With Y our V ehicle Battery 1. Follow all instructions published by the battery manufacturer and the manufact urer of the equipment in which the battery is installed. 2. Make sure the area around the battery is well ventilated.
Important Safety Information vii 10. If battery acid contacts skin or clothing, wash immediately with soap and wa ter . If acid enters your eyes, immediatel y flood them with running cold water for at least twenty minutes and get medical attention immediately .
Important Safety Information viii Precautions for Using Rechar geable Appliances Most rechargeable battery-operated equipment uses a separate char ger or transformer that is plugged into an AC receptacle and produces a low voltage charging output. Some chargers for rechar geable batteries can be damaged if connected to the XPower Powerpack 300.
ix Contents 1 Introduction About the XPower Powerpac k 300 - - - - - - - - - - - - - - - - - - - - - 1 Comprehensive Protection - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 Automatic Overlo.
x Using the Air Compressor - - - - - - - - - - - - - - - - - - - - - - - - - - 21 Over-temperature Safety Protection - - - - - - - - - - - - - - - - - 21 Inflating Tires - - - - - - - - - - - - - - - .
1 1 Intr oduction About the XP ower P owerpack 300 Easy-to-use and designed for years of reliable service, the XPower Powerpack ca n run many AC appliances and 12 V DC appliances whe never you need power for work or play , at home or on the ro ad.
Comprehensive Protection 2 Low Battery Protection Low battery protection protects the internal battery from excessive discharge and possible damage. When the AC Power ON / OFF switch is turned ON , an audible alarm alerts you when the internal battery is nearly dischar ged (1 1.
3 2 F e atur es Chapter 2 describes the main features of the XPowe r Powerpack 300. W e recommen d that you familiarize yourself with these features before operating the unit.
XP ower P owerpack F eatures 4 XP ower P owerpack F eatures Front P anel Detail Fe a t u r e D e s c r i p t i o n 1 DC power outlet : • Powers 12 V D C auto, R V or marine appliances • Rechar ges XPower Powerpack from a 12 V outlet in a vehicle using the DC charging cable.
XP ower P owerpack F eatures 5 4 Battery S tatus LED illuminates when the XPower Powerpack is charging (when an AC char ger is connected to the XPower Powerpack’ s AC char ger input socket and plugged into the household 120 V AC outlet).
XP ower P owerpack F eatures 6 Left Side V iew Fe a t u r e D e s c r i p t i o n 1 Pressur e gauge shows the PSI (lb/in 2 ). 2 Jump-starting clamp 3 Jump-start power switch 4 AC charger input socket .
XP ower P owerpack F eatures 7 Accessories Accessory Description 1 AC charger lets you recharge the XPower Powerpack from a standard AC wall outlet and can onl y be us ed to recharge the internal battery of the XPower Powerpack. 2 DC charging cable lets you recharge the XPower Powerpack from a 12 V system in a car , SUV , R V or a boat.
8.
9 3 Oper ation Chapter 3 explains how to operate the XPower Powerpack 300 ef ficiently . This chapter cove rs: • Recharging the XPower Powe rpack for first-time use • Using the flashlight • Oper.
Choosing a Location 10 • Motor loads with high startup power sur ge requirements: Sump pumps, circular saws, lar ger power tools, refrigerators. V isit www .
Using XP ower P owerpack for the F irst T ime 11 Using XP ower P owerpack for the First Time Rechar ging with the A C Charg er Rechar ging with the AC ch ar ger is a true “plug -in-and- forget” char ging method. W e recommend leaving the AC charger connected when the XPow er Powerpack is not in use.
Recharging with the AC Charger 12 Import ant: The 24-hour charging time for the XPower Powerpack assumes that there is 12 0 V AC at the AC wall outlet. If the voltage is less than 120 V AC, it may take more than 24 hours to fully recharge the XPow er Powerpack.
Using the Flashlight 13 Using the Flashlight The XPower Powerpack has a detachable flashlight that operates for up to 18 hours be fore needing to be rechar ged. T o detach the flashlight, push the rim of the flashlight lens straight back, then swing the light away from the unit.
Operating AC Appliances 14 Operating A C Appliances Understanding A C Appliances AC appliances are rated by how much electrical power (in watts) they consume. XPower Powerpac k can power most appliances within its contin uous power rating (240 W , 1 A).
Operating AC Appliances 15 High Surg e Appliances The wattage rating of AC app liances is the average power used by the appliance. Applia nces such as televisions and appliances with motors consum e much more power than their average rating when they are first switched on.
Operating AC Appliances 16 Operating Sever al Appliances at Once Y ou can run several AC appliances if the total rating of all the appliances (in watts) does not exceed 240 W . Run time, however , will decrease accordingly with the number of appliances being operated and the AC power being consumed.
Operating 12 V DC Appliances 17 Operating 12 V DC Appliances The XPower Powerpack can operate 12 V DC auto, R V , marine, or other portable appliances th at draw 12 A or less from a 12 V DC power outlet or from a vehicle’ s lighter socket. T ypical 12 V DC appliances that can be us ed with the XPower Powerpac k are listed in T able 3- 2.
Jump-Starting a V ehicle’ s Engine 18 T o operate a 12 V DC appliance: 1. Open the protective cover on the DC power outlet of the XPower Powerpack. 2. Plug the 12 V DC appliance into the DC power outlet on the left side of the unit, and turn the 12 V DC appliance on (if required).
Jump-Starting a V ehicle’ s Engine 19 T o jump-start a vehicle or boat engine: 1. T urn off the vehicle or boat ignition and all accessories. 2. Engage the park or emer gency brake and place the transmission in park for an automatic or neutral for a manual.
Jump-Starting a V ehicle’ s Engine 20 If no alarm sounds, and the Green Jumpstar t Connection LED is illuminated, then proceed to the next step. 7. Switch ON the jump-starting power switch. Before starting the engine, make sure the XPower Powerpack and the cables are clear of belts and fans.
Using the Air Compressor 21 Using the Air Compressor Over -temper ature Safety Protection It is recommended that you fo llow the warnings and turn the compressor off for 10 minutes after every 10 minutes of operation.
Using the Air Compressor 22 Inflating Tires T o inflate your vehicl e, mo tor cycle, or bicycle tir e s: 1. Place the valve connector secure ly on the tire valve stem, push it as far as possible to allow normal airflow , and close the thumb latch. If necessary , use a supplied nozzle adaptor .
Using the Air Compressor 23 3. T urn the compressor off after appropriate pressure is reached. 4. Open the thumb l atch and remove the valve co nnector from the valve stem. 5. Check air pressure w ith a pressure ga uge. Inflating Small Sports Equipment Y ou can use the compressor to inflate small sports equipment such as soccer balls and footballs.
Connecting to an External Battery 24 6. Remove nozzle adaptor from valve connector and store in storage compartment. Connecting to an External Battery Y ou can extend battery opera ting times by connecting the XPower Powerpack to a lar ger external battery .
Connecting to an Ext ernal Battery 25 T o connect the XPowe r Powerp ack to an external battery using the jump-start cables: 1. Ensure that the jump-start power switch is OF F . 2. Connect the red positive (+) clamp of the cables to t he red positive (+) te rminal of the external battery .
26.
27 4 Maintenance Chapter 4 provides information on maintaining your internal battery , recharging options for the internal battery , and replacing user -replaceable parts. Routine maintenance is requir ed to keep your XPower Powerpack 300 operating properly .
Recharging the XP ower P owerpack Batter y 28 Rechar ging the XP ower P owerpack Battery T o check the XPower Powerpack’ s charge level, press the Battery Level button. Y ou can rechar ge the battery using: • the fully automatic “plug- in-and-for get” AC charger .
Recharging the XP ower P owerpack Battery 29 T o r echarge with the AC charger: 1. Disconnect any 12 V DC appliances from the DC power outlets. 2. Disconnect an y AC products from the XPower Powerpack and turn the AC Power ON / OF F switch to OF F . 3.
Recharging the XP ower P owerpack Batter y 30 Recharging with the DC Char ging Cable Using the DC charging cable, the XPower Powerpack can be recharged while you drive your ve hicle. T o recharge the XPower Powe rpack while you drive using the DC charging cable: 1.
Recharging the XP ower P owerpack Battery 31 Note : The Battery Level LEDs are only accurate when the XPower Powerpack has been disc onnected from all appliances and all charging sources for 15 minutes. Import ant: • • Do not leave the XPower Powe rpack permanently connected to the vehicle’ s lighter socket or 12 V accessory outlet.
Recharging the XP ower P owerpack Batter y 32 Recharging with a Gener ator’ s Regulated 12 V DC Outlet Refer to the Owner ’ s Guide acco mpanying your generator for detailed instructions on conn ecting the gene rator to a unit like the XPower Powerpack.
Recharging the XP ower P owerpack Battery 33 Recharging fr om a Solar P anel Small, unregulated 12 V solar panels rated to produce a maximum of 2.5 A (or 30 W) can be used to charge the XPower Powerpack through the AC charger Input socket. Y ou will need to purchase a standard 5.
Recycling 34 Recycling The XPower Powerpack i s designed to prov ide years of service. However , when the inte rnal battery reaches the end of its service life, the XPower Powerpack itself is no longer of use. The internal battery is not desi gned to be user replaceable.
35 5 T r oubleshooting T roubleshooting will help you id entify the common problems than can occur with the XPower Powerpack 300. If you cannot solve the problem with th e XPower Powerpack, record the information asked fo r on “Information Abou t Y our System” on page 48 and then contact your dealer .
T roubleshooting Reference 36 T r oubleshooting Reference W ARNING: Electric shock hazard Do not remove t he cover of the XPower Pow erpack or disassemble the XPower Powerpack. The XPower Powerpack does not contain any internal user -serviceable parts and attempting to service the unit yourself could result in electrical shock or bu rn.
T roubleshooting Refe rence 37 AC appliance will n ot operate; audible alarm is soundin g. Battery has discharged to 10.5 V . XPower Powerpack has overheated due to poor ventilation or excessively warm environm ental conditions. Tu r n OFF th e AC Po wer ON / OFF switch and rechar ge the XPower Powerpack.
T roubleshooting Reference 38 Measured AC output voltage is too low . Using an average-reading AC voltmeter to read output voltage. XPower Powerpack battery is almo st fully discharged. The modifi ed sine w ave output of the XPower Powerpack requires a true RMS reading meter , su ch as the Fluk e 87 series, for accurate measurement.
T roubleshooting Refe rence 39 The engine being jum p- started will no t start. XPower Powerpack battery is not fully char ged. The engine condition is poor . The engine start capacity exceeds the XPower Powerpack jump -start capability . Rechar ge the XPower Powerpack battery .
40.
41 A Specifications Electrical Specifications 12 V DC Section Internal battery type Sealed/non-spillable, AGM (Absorbed Glass Mat) lead- acid Internal battery volt age (nominal) 12 V DC Internal batt.
Electrical Specifications 42 AC P ower Section Output power • Continuous output po wer • Peak output power • AC output sur ge capacity 240 W 300 W 480 W Output voltage 120 ± 10 V AC RMS Output frequency 60 Hz ± 1 Hz Output wave form modified sinewave No load current draw <0.
Physical Specifications 43 Physical Specifications Air Compre ssor Pressure 250 PSI (lb/in 2 ) Accessories DC charge cable 39" (1 m) 18 A WG wit h male to male lighter plu gs (part # 449-018 7-01-01) AC charger Input: 120 V AC, 60 Hz, 1 1 W Output: 13.
44.
45 W arranty and Return Wa r r a n t y What does this warranty cover? This Limited W arranty is provided by Xantrex T echnology Inc. ("Xantrex") and covers defects in workmans hip and materials in your XPower Powerpack 300.
W arranty and Return 46 What does this warranty not cover? This Limi ted W arranty does not cover normal wear and tear of the pr oduct or costs related to the removal, installation, or troublesh ooting of the custo mer 's electrical sy stems.
W arranty and Return 47 warranties or on the duration of an implied warranty or on th e limitation or exclusion of incidental or conseque ntial damages, so the above limitation( s) or exclusion(s) may not apply to you. This Limited W arranty gives you specific legal rights.
W arranty and Return 48 Out of W arranty Service If the warranty period for your XPower Powerpack 300 has expired, if the unit was damaged by misuse or in correct installation, if other conditions o f the warranty have not been met, or if no dated proof of purchase is available, your unit may be serviced or replaced for a flat fee.
デバイスXantrex Powerpack 300の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Xantrex Powerpack 300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはXantrex Powerpack 300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Xantrex Powerpack 300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Xantrex Powerpack 300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Xantrex Powerpack 300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はXantrex Powerpack 300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Xantrex Powerpack 300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちXantrex Powerpack 300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
