Xeroxメーカー8264Eの使用説明書/サービス説明書
ページ先へ移動 of 30
1 September 2008 701P49052 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide.
.
100kg Unwinder / Winder User G uide i Table of Contents 1 Safety and Warning Label Information.................................................................. 1 1.1 Safety Cons iderations .............................................................
ii 100kg Unwinder / Winder User G uide This page has been intentionally left blank..
100kg Unwinder / Winder User G uide 1 1 Safety and Warning Label Information 1.1 Safety Considerations Various procedures throughout this user guide may list 2 levels of safety indicators that need to be adhered to during the performance of a procedu re.
1 Safety and Warning Label Information 2 100kg Unwinder / Winder User Guide 1.2.1 Warning Label Locations and Types The figures below indicate the lo cations of the warning labels. 1 1 Figure 1. Front Warning Label Locations 1 1 Figure 2. Rear Warning Label Location s No.
1 Safety and Warning Label Information 100kg Unwinder / Winder User G uide 3 1.3 Operating Instructions Labels This section explains the different types of operating instructions l abels and wher e they are located.
1 Safety and Warning Label Information 4 100kg Unwinder / Winder User Guide This page has been intentionally left blank..
100kg Unwinder / Winder User G uide 5 2 Unwinder / Winder Operation 2.1 Location of Major Components This section will explain the names and functions of the major com ponents of the Unwinder / Winder. 2.1.1 Unwinder Components 1 1 2 3 Figure 4. Location of Major Components (Unwinder) No.
2 Unwinder / Winder Operation 6 100kg Unwinder / Winder User Guide 2.1.2 Winder Components 1 1 3 2 4 Figure 5. Location of Major Components (Winder) No. Part name Function 1 Winder Spindles Rolls in the media after printing 2 Winder Tension Bar Roller Used to guide the media after printing to the r oll-in device.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 7 2.1.3 Unwinder Control Panel The Unwinder Control Panel is used to set the operating mode and to displa y the status of the Unwinder. 2 5 3 1 4 Figure 6. Unwinder Control Panel 2.1.3.
2 Unwinder / Winder Operation 8 100kg Unwinder / Winder User Guide 2.1.4 Winder Control Panel The Winder Control Panel is used to set the operati ng mode and to display the status of the Winder. 4 3 2 1 Figure 7. Winder Control Panel 2.1.4.1 Switches No.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 9 2.2 Connecting the Power Cable This section describes the procedu re for connecting the power cable. z DO NOT use a damaged power cable. If the power cable is damaged, contact your local Xerox Customer Service Representative for a replacement.
2 Unwinder / Winder Operation 10 100kg Unwinder / Winder User G uide 2.3 Turning the Power ON and OFF The following section provides procedures for setting the Unwinder / Winder power ON and OFF. 2.3.1 Turning the Power ON Turn the power ON by following the instructions below.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 11 2.4 Loading Roll Media onto the Unwinder The following section describes how to load roll media on the Unwinder. Media core size 3 inch ： Maximum media width 1625mm, Mi nimum media width 100 0mm, media outside diameter less than 250mm, weight less than 100kg.
2 Unwinder / Winder Operation 12 100kg Unwinder / Winder User G uide 4. Place the roll media on top of the rear rail. 1 2 Figure 14. Install Roll Media No. Part name 1 Rear Rail 2 Roll Media 5. Set the roll media on the Left Unwinder Sp indle and tighten the Left Unwinder Spindle Locking Handle.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 13 6. Set the roll media on the Right Unwinder Spindl e and tighten the Right Spindle Locking Handle. 3 2 1 Figure 16. Install Roll Media No. Part name 1 Right Unwinder Spindle 2 Roll Media 3 Ri ght Spindl e Locking Ha ndle 7.
2 Unwinder / Winder Operation 14 100kg Unwinder / Winder User G uide 8. Set the Printer Power Switch to ON. After an sh ort initialization period the Printer Control Panel will display “No Media”. 9. Raise the Media Set Lever. The Printer C ontrol Panel will display “Please Set Media”.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 15 11. Set the Unwinder Automatic Operation Switch as described below: ・ If the paper will be printed on the outsi de of the roll media: OUTSIDE ROLL ・ If the paper will be printed on the insi de of the roll media: INSIDE ROLL Figure 20.
2 Unwinder / Winder Operation 16 100kg Unwinder / Winder User G uide 13. Insert the roll media into the tension roller, and then into the Rear Printer Platen. Media can be inserted either with the print surf ace on the outside (Figure 22) or wi th the print surface on the inside (Figure 23).
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 17 b. When using a roll paper where the print surface is on the inside. Damage and problems that occur because of the use of roll medi a where the print surface is on the inside are not covered by the warranty.
2 Unwinder / Winder Operation 18 100kg Unwinder / Winder User G uide 14. Pull about 1 meter of roll media out from the Front Printer Plate. 1 2 Figure 24.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 19 1 2 1 Figure 26. Install Roll Media No. Part name 1 Roll Media 2 Media Setting Guide 16.
2 Unwinder / Winder Operation 20 100kg Unwinder / Winder User G uide 17 Push the “INITIALIZE” button on the Unwinder Control Panel. Figure 28. Push INITIALIZE 18 Close the Printer Front Cover.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 21 2.5 Operating the Winder This section provides instructions for using the Unwinder / Winder. 1. Set a media core on the Winder. Ensure that the si ze of the core is that same size as the media roll core.
2 Unwinder / Winder Operation 22 100kg Unwinder / Winder User G uide 4. Attached the tip of the roll m edia to the media core on the Winder Spindles. Ensure that the media parallel to the core. Secure the ti p of the media to the core with tape. 2 1 3 Figure 31.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 23 2.6 Removing a Printed Media Core from the Winder This section will explain t he procedure to remove the media core from the Winder. 1. Set the Winder Automatic Operation Switch to OFF.
2 Unwinder / Winder Operation 24 100kg Unwinder / Winder User G uide This page has been intentionally left blank..
.
26 100kg Unwinder / Winder User G uide Prepared by: XEROX Corporation Global Knowledge and Language Services 800 Phillips Road, Bldg. 0218-01A Webster, New York 14580-9791 USA ©2008 by XEROX Corporation.
デバイスXerox 8264Eの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Xerox 8264Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはXerox 8264Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Xerox 8264Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Xerox 8264Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Xerox 8264Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はXerox 8264Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Xerox 8264Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちXerox 8264Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
