Yamahaメーカー6M8-F8199-18の使用説明書/サービス説明書
ページ先へ移動 of 65
8D O WNER’S MANU AL 6M8-F8199-18 U .S.A.Edition LIT -18626-05-81 6M8-9-18 Hyoshi 1/21/04 6:49 PM Page 1.
EMU25060 ZMU01690 Read this owner ’ s manual carefully before operating your outboard motor. 6M8-9-18 Hyoshi 1/21/04 6:49 PM Page 2.
Important manual information EMU25100 To the owner Thank you for choosing a Yamaha outboard motor. This Owner’s Manual contains infor- mation needed for proper operation, mainte- nance and care. A thorough understanding of these simple instructions will help you ob- tain maximum enjoyment from your new Yamaha.
Table of contents General information .......................... 1 Identification numbers record .......... 1 Outboard motor serial number .......... 1 Emission control information ........... 1 North American models..................... 1 Safety information .
Table of contents models) ......................................... 34 Cleaning and anticorrosion measures ...................................... 34 Cleaning the outboard motor .......... 34 Checking painted surface of motor ..........................
1 General information EMU25170 Identification numbers record EMU25182 Outboard motor serial number The outboard motor serial number is stamped on the label attached to the port side of the clamp bracket or the upper part of the swivel bracket.
General information 2 EMU25360 Safety information ● Before mounting or operating the outboard motor, read this entire manual. Reading it should give you an understanding of the motor and its operation ● Before operating the boat, read any own- er ’ s or operator ’ s manuals supplied with it and all labels.
General information 3 a Float Plan with a responsible person. Be sure to cancel the Float Plan when you re- turn. ● Use common sense and good judgment when boating. Know your abilities, and be sure you understand how your boat han- dles under the different boating conditions you may encounter.
General information 4 starting device. ● The engine will not start unless the shift control is in neutral position. EMU25500 Basic boating rules (Rules of the road) Just as there are rules which apply when you are driving on streets and high ways, there are waterway rules which apply when you are driving your boat.
General information 5 Give-Way vessel). Any vessels in the shad- ed area must yield to you (they are the Give- Way vessels). Both you and the meeting vessel must alter course to avoid each other.
General information 6 need to carry a portable air horn, available from local marine supply stores. Fishing vessel right-of-way All vessels which are fishing with nets, lines or trawls are considered to be “ fishing ves- sels ” under the International Rules.
General information 7 EMU25540 Fueling instructions W ARNING EWM00010 GASOLINE AND ITS VAPORS ARE HIGH- LY FLAMMABLE AND EXPLOSIVE! ● Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. ● Stop engine before refueling.
General information 8 dry rags. ● Do not overfill the fuel tank. ● Tighten the filler cap securely after re- fueling. ● If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention.
General information 9 NO TE: Select a propeller which will allow the engine to reach the middle or upper half of the oper- ating range at full throttle with the maximum boat load.
10 Basic components EMU25795 Main components NO TE: * May not be exactly as shown; also may not be included as standard equipment on all mod- els. 8D EMU25802 Fuel tank If your model was equipped with a portable fuel tank, its function is as follows.
Basic components 11 tions. EMU25830 Fuel joint This joint is used to connect the fuel line. EMU25841 Fuel gauge This gauge is located on either the fuel tank cap or on the fuel joint base. It shows the ap- proximate amount of fuel remaining in the tank.
Basic components 12 EMU25961 Throttle indicator The fuel consumption curve on the throttle indicator shows the relative amount of fuel consumed for each throttle position. Choose the setting that offers the best performance and fuel economy for the desired operation.
Basic components 13 could cause people and objects in the boat to be thrown forward. NO TE: The engine cannot be started with the lock plate removed. EMU26001 Engine stop button To open the ignition circuit and stop the en- gine, push this button.
Basic components 14 To increase resistance, turn the adjuster clockwise. To decrease resistance, turn the adjuster counterclockwise. W ARNING EWM00040 Do not overtighten the friction adjuster. If there is too much resistance, it could be difficult to steer, which could result in an accident.
Basic components 15 1. T op co wling lock lev er(s) ZMU02862 1.
16 Operation EMU26901 Installation CAUTION: ECM00110 Incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat, or accessories such as transom ladders or depth finder transducers) can create airborne water spray while the boat is cruising.
Operation 17 motor greatly affects the water resistance. If the mounting height is too high, cavitation tends to occur, thus reducing the propulsion; and if the propeller tips cut the air, the engine speed will rise abnormally and cause the en- gine to overheat.
Operation 18 board (if packed). For details, consult your Yamaha dealer. W ARNING EWM00650 Avoid using bolts, nuts or washers other than those contained in the engine pack- aging. If used, they must be of at least the same quality of material and strength and must be tightened securely.
Operation 19 cool. 4. Third through tenth hours: Avoid operating at full throttle for more than 5 minutes at a time. Let the engine cool between full-throttle runs. Vary en- gine speed occasionally. 5. After the first 10 hours: Operate the engine normally.
Operation 20 EMU27402 Gasoline and oil mixing (100:1) If equipped with a portable fuel tank 1. Pour oil into the portable fuel tank, and then add gasoline. 2. Replace the fuel tank cap and close tightly. 3. Shake the fuel tank to mix the fuel thor- oughly.
Operation 21 2. If there is a fuel joint on the motor, firmly connect the fuel line to the joint. Then firmly connect the other end of the fuel line to the joint on the fuel tank. 3. If a steering friction adjuster is provided on your outboard motor, securely attach the fuel line to the fuel line clamp.
Operation 22 to a secure place on your clothing, or your arm or leg while operating. ● Do not attach the lanyard to clothing that could tear loose. Do not route the lanyard where it could become entan- gled, preventing it from functioning. ● Avoid accidentally pulling the lanyard during normal operation.
Operation 23 NO TE: ● When the engine is cold, it needs to be warmed up. For further information, see page 23. ● If the engine does not start on the first try, repeat the procedure. If the engine fails to start after 4 or 5 tries, open the throttle a small amount (between 1/8 and 1/4) and try again.
Operation 24 2. Move the gear shift lever quickly and firmly from neutral to forward. Remote control models 1. Pull up the neutral interlock trigger (if equipped) and move the remote control lever quickly and firmly from neutral to forward. EMU27795 Reverse (manual tilt and hydro tilt models) W ARNING EWM00190 When operating in reverse, go slowly.
Operation 25 until the engine comes to a complete stop. 2. After stopping the engine, tighten the air vent screw on the fuel tank cap and set the fuel cock lever or knob to the closed position, if equipped. 3. Disconnect the fuel line if you are using an external fuel tank.
Operation 26 EMU27871 Adjusting trim angle for manual tilt models There are 4 or 5 holes provided in the clamp bracket to adjust the outboard motor trim an- gle. 1. Stop the engine. 2. Remove the trim rod from the clamp bracket while slightly tilting the outboard motor up.
Operation 27 the boat is up about 3 to 5 degrees. With the bow up, the boat may have a greater tenden- cy to steer to one side or the other. Compen- sate for this as you steer. The trim tab can also be adjusted to help offset this effect. When the bow of the boat is down, it is easier to accelerate from a standing start onto plane.
Operation 28 will be tilted for more than a few minutes. Otherwise fuel may leak. CAUTION: ECM00230 ● Before tilting the outboard motor, fol- low the procedure under “ Stopping en- gine ” in this chapter. Never tilt the outboard motor while the engine is run- ning.
Operation 29 EMU28013 Procedure for tilting down (manual tilt models) 1. Slightly tilt the engine up. 2. On models equipped with a tilt support knob, pull it out. 3. Slowly tilt the engine down. EMU28060 Cruising in shallow water The outboard motor can be tilted up partially to allow operation in shallow water.
Operation 30 3. The shallow water lever will lock, sup- porting the outboard motor in a partially raised position. 4. When lowering the outboard motor, slightly tilt it up and push the shallow wa- ter lever down. Slowly lower the out- board motor to the normal position.
31 Maintenance EMU28214 Specifications Dimension: Overall length: 802 mm (31.6 in) Overall width: 343 mm (13.5 in) Overall height S: 977 mm (38.5 in) Transom height S: 436 mm (17.2 in) Weight (AL) S: 27.0 kg (60 lb) Performance: Full throttle operating range: 4500 – 5500 r/min Maximum output: 5.
Maintenance 32 whether in a boat or car. ● DO NOT fill fuel container to maximum capacity. Gasoline will expand consid- erably as it warms up and can build up pressure in the fuel container.
Maintenance 33 EMU28301 Procedure EMU28372 Flushing in a test tank 1. Wash the outboard motor body using fresh water. For further information, see page 34. 2. Fill the fuel tank with fresh fuel and add one ounce of “ Yamaha Fuel Conditioner and Stabilizer ” (Part No.
Maintenance 34 EMU28400 Lubrication (except oil injection models) 1. Grease the spark plug threads and in- stall the spark plug(s) and torque to proper specification. For information on spark plug installation, see page 37. 2. Change the gear oil. For instructions, see page 42.
Maintenance 35 have the mechanical skills, tools, and other equipment necessary to perform mainte- nance not covered by this owner ’ s manual. EMU28510 Replacement parts If replacement parts are necessary, use only genuine Yamaha parts or parts of the same type and of equivalent strength and materi- als.
Maintenance 36 EMU28521 Maintenance chart Frequency of maintenance operations may be adjusted according to the operating condi- tions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action.
Maintenance 37 EMU28931 Greasing Yamaha marine grease (Water resistant grease) 8D EMU28950 Cleaning and adjusting spark plug W ARNING EWM00560 When removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire.
Maintenance 38 attempt to diagnose any problems yourself. Instead, take the outboard motor to a Yamaha dealer. You should periodically re- move and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode.
Maintenance 39 Checkpoints ● Fuel system parts leakage ● Fuel line joint leakage ● Fuel line cracks or other damage ● Fuel connector leakage EMU28990 Checking fuel filter Check the fuel filter periodically. The fuel fil- ter is a one piece, disposable type.
Maintenance 40 or other qualified mechanic. 2. Verify whether the idle speed is set to specification. For idle speed specifica- tions, see page 31. EMU29111 Checking wiring and connectors ● Check that each grounding wire is properly secured. ● Check that each connector is engaged se- curely.
Maintenance 41 ● Check the propeller shaft oil seal for dam- age. NO TE: If the shear pin equipped: it is designed to break if the propeller hits a hard underwater obstacle to help protect the propeller and drive mechanism. The propeller will then spin freely on the shaft.
Maintenance 42 align it with the hole. EMU29280 Changing gear oil W ARNING EWM00800 ● Be sure the outboard motor is securely fastened to the transom or a stable stand. You could be severely injured if the outboard motor falls on you. ● Never get under the lower unit while it is tilted, even when the tilt support lever or knob is locked.
Maintenance 43 pors are flammable and explosive. ● If you have any question about properly doing this procedure, consult your Yamaha dealer. ● Keep away from sparks, cigarettes, flames, or other sources of ignition when cleaning the fuel tank. ● Remove the fuel tank from the boat be- fore cleaning it.
Maintenance 44 EMU29400 Coating the boat bottom A clean hull improves boat performance. The boat bottom should be kept as clean of ma- rine growth as possible. If necessary, the boat bottom can be coated with an anti-foul- ing paint approved for your area to inhibit marine growth.
45 Trouble Recovery EMU29422 Troubleshooting A problem in the fuel, compression, or igni- tion systems can cause poor starting, loss of power, or other problems. This section de- scribes basic checks and possible remedies, and covers all Yamaha outboard motors.
Trouble Recovery 46 Q. Is fuel system obstructed? A. Check for pinched or kinked fuel line or other obstructions in fuel system. Q. Is fuel contaminated or stale? A. Fill tank with clean, fresh fuel. Q. Is fuel filter clogged? A. Clean or replace filter.
Trouble Recovery 47 A. Have serviced by a Yamaha dealer. Q. Is load on boat improperly distributed? A. Distribute load to place boat on an even plane. Q. Is water pump or thermostat faulty? A. Have serviced by a Yamaha dealer. Q. Is there excess water in fuel filter cup? A.
Trouble Recovery 48 Q. Is heat range of spark plug incorrect? A. Inspect spark plug and replace it with rec- ommended type. Q. Is high pressure fuel pump drive belt bro- ken? A. Have serviced by a Yamaha dealer. Q. Is engine not responding properly to shift lever position? A.
Trouble Recovery 49 your arm or leg while operating. ● Do not attach the lanyard to clothing that could tear loose. Do not route the cord where it could become entangled, preventing it from functioning. ● Avoid accidentally pulling the lanyard during normal operation.
Trouble Recovery 50 up. 6. Insert the knotted end of the emergency starter rope into the notch in the flywheel rotor and wind the rope several turns around the flywheel clockwise. 7. Give a strong pull straight out to crank and start the engine. Repeat if neces- sary.
Trouble Recovery 51 5. Take the outboard motor to a Yamaha dealer as soon as possible. CAUTION: ECM00400 Do not attempt to run the outboard motor until it has been completely inspected.
52 Consumer information EMU29811 Important warranty information for U.S.A. and Canada.
Consumer information 53.
Consumer information 54 EMU29820 YAMAHA MOTOR CORPORATION, U.S.A. OUTBOARD MOTOR TWO YEAR LIMITED WARRANTY.
Consumer information 55.
Consumer information 56.
Consumer information 57 EMU29840 IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE U.S.A. OR CANADA.
Printed in Fr ance April 2004–0.5 × 1 ! 6M8-9-18 Hyoshi 1/21/04 6:49 PM Page 4.
Warranty card 12/6/01 7:40 PM Page 1.
Warranty card 12/6/01 7:40 PM Page 2.
デバイスYamaha 6M8-F8199-18の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Yamaha 6M8-F8199-18をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha 6M8-F8199-18の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha 6M8-F8199-18の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha 6M8-F8199-18で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha 6M8-F8199-18を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha 6M8-F8199-18の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha 6M8-F8199-18に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha 6M8-F8199-18デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
