Yamahaメーカー900SWの使用説明書/サービス説明書
ページ先へ移動 of 24
Soavo-900SW SUBWOOFER SYSTEM UB OWNER’S MANUAL.
i En IMPOR T ANT SAFETY INSTR UCTIONS 1 Read these instr uctions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilat ion openings.
ii En W e W ant Y ou Listening For A Lifetime YAMAHA and the Electronic I ndustries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
iii En Thank you for selecting th is YAMAHA subwoofer system. Please read the following oper ating precautions before use. YAMAHA will not be held responsible for any damage and/or injury caused by not follo wing the cautions below. 1 To assure the finest performance , please read this manual carefully.
1 En • VOLTAGE SELECTOR (Asia and General models only) The voltage selector switch on the rear panel of this unit must be set for your local main voltage BEFORE plugging this unit into the AC main supply. Voltages are 110/120/220/230-240 V AC, 50/60 Hz.
2 En ◆ High 600 W dynamic power ◆ L.F.E input terminal ◆ Sleep timer ◆ Remote control capability You can make setting changes and adjustments for this unit by using the remote c ontrol from your listening position.
3 En GETTING ST ARTED ■ Front panel 1 Remote control sensor Receives signals from the remote control. 2 STANDBY/ON indicator Green : Lights up when this unit is on. Red : Lights up when this unit is in the standby mode. Orange : Lights up when the sleep timer is on.
4 En GETTING ST ARTED ■ Rear panel 1 GND terminal See page 12 for connection information. 2 INPUT 3 terminals See pages 7 - 8 for connection information. 3 INPUT 2 (LFE) terminals See page 8 for connection information. 4 OUTPUT terminals See page 10 for connection information.
5 En GETTING ST ARTED ■ Installing the batteri es in the remote control 1 Press the mark on the battery cover and open the cover. 2 Insert the two supplied type AA, R6, UM-3 batteries following the indications (+/–) inside the battery compartment.
6 En The position of the subwoofer is not so critical because bass sound is not highly direc tional. For a sonorous sound field, the use of two subwoofers is recommende d, althou gh you can obtain a good effect with one subwoofer.
7 En See pages 7 - 8 when your amplifier has subwoofer (line out) terminal(s), or se e pages 9 - 11 when your amplifier has no subwoofer (line out) terminal. • Do not connect the power cord of this unit and other components into an AC outlet until all connect ions between components ar e completed.
8 En CONNECTIONS ■ Using two s ubwoofers Connect the “R” side subwo ofer terminal of your amplifier to the INPUT 3 ( ) terminal on this unit using a commercially available mono pin cable, and co.
9 En CONNECTIONS Connect an amplifier (and front speakers) to this unit using co mmercially available speaker cables. Refe r to the following instructions to make connections. ■ Connecting to the sp eaker cable 1 Remove approximately 10 mm (3/8”) of insulation from each of the speaker cables.
10 En CONNECTIONS When y our amplifier has one set of fr ont speaker terminal s Connect the speaker terminals of the ampl ifier to the INPUT 1 terminals of this unit, and connect th e OUTPUT terminals of this unit to the front speakers using a comm ercially available speaker cable.
11 En CONNECTIONS When y our amplifier has t wo sets of f ront speaker terminals and both terminals c an output sound signals sim ultaneously • Connect one set of front speaker termin als of the amp.
12 En CONNECTIONS If this unit or the amplifie r makes a hamming noise when connecting to the speaker te rminals of your amplifier, connect both of the GND (ground) terminals on your amplifier and this unit usi ng commercia lly available grounding wire as shown in fig.
13 En Before using this unit, adjust the volu me balance of this unit to obtain the opt imu m volume and tone balance between the front speakers and this unit by following the procedures below. 1 Set POWER switch on the rear panel of this unit to the ON position, and then press POWER to turn on this unit.
14 En USING THIS UNIT You can store up to 3 sets of your favorite settings (volume, high-cut, phase and B.A.S.S. setting) in this uni t. ■ Storing t he setting In the following procedure, PRESET 1 is used as an example. 1 Adjust the sound balance between the volume, high cut, phase and B.
15 En USING THIS UNIT * This function is available only for Yamaha amplifiers that meet the following conditions: – The amplifier was released in 2005 or later. – The remote control of th e amplifier has two different buttons for STANDBY and ON. When the AMP ID library code of the remote control has been changed, this function may not work.
16 En USING THIS UNIT Frequency re sponse of this unit The figures below show the optimum adjustment of each control and the frequency respons e when this subwoofer is combined with a typical front spea ker system.
17 En In 1988, Yamaha brought to th e speaker systems utilizing YST (Yamaha Active Servo Te chnology) to give powerful, high quality bass re production. This technology uses a direct connection between th e amplifier and speaker, allowing accurate si gnal tran smission and precise speaker control.
18 En Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized Yamaha dealer or service center.
19 En Type .... Advanced Yamaha Active Servo Technology II Driver .. ........... ........... ........... ... 25 c m (10”) cone woofer Magnetic shielding type Amplifier Output (100 Hz, 4 ohms, 10% T.H.D) ...................... ............ ..........
©2006 All rights reserved. YAMAHA ELECTRONICS CORPORATION, US A 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S .A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SC ARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-3 4, 25462 RELLINGEN BEI HAMBURG, GERMAN Y YAMAHA ELECTRONIQUE FRANCE S.
デバイスYamaha 900SWの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yamaha 900SWをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha 900SWの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha 900SWの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha 900SWで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha 900SWを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha 900SWの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha 900SWに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha 900SWデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。