YamahaメーカーCRW4261t-NBの使用説明書/サービス説明書
ページ先へ移動 of 25
CRW4261t SERIES User Guide Guide de I’utilisateur Bedien ungsanleitung.
COMPLIANCE INFORMA TION ST A TEMENT (DECLARA TION OF CONFORMITY PROCEDURE) Responsible P ar ty: Y amaha Systems T echnology , Inc. Address: 100 Centur y Center Cour t San Jose, Calif or nia 95112 T el.
T his output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 Material : GaAlAs Wavelength : 780-790 nm Emission Duration : Continuous Laser Output Power : Less than 44.
WARNING i W ARNING ❢ W ARNING ❢ • The temperature where CR W4261t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CR W4261t cover to reduce the risk of electric shock. • Always remo ve the disc before transporting CR W4261t.
Important Precautions ii Impor tant Precautions Please read the follo wing precautions before attempting to operate the CR W4261t. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remov er . A dust particle on the disc may cause recording to fail, producing an unusable disc.
Table of Contents iii Table of Contents Introduction ............................................................................... 1 CRW4261t Features ........................................................ 1 Orange Book Compatible Recording ......
Introduction 1 Intr oduction Thank you for purchasing a Y amaha CR W4261t drive. Please read this manual before using the driv e in order to mak e the best use of the superior CR W4261t functions. After reading, please retain this manual for future reference.
Introduction 2 Orange Book Compatible Recording T rack at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD- R OM drives other than a CD-R W or a CD-R drive until the session is closed.
Chapter 1 - System Configuration 3 Chapter 1 - System Configuration Before using the CR W4261t, make sure that you hav e all of the items on the list of included items.
Chapter 1 - System Configuration 4 Discs On the CR W4261t, you can use con ventional CD-R W and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and 3 (Orange Book).
Chapter 2 - Installing the Yamaha CRW4261t Drive 5 Chapter 2 - Installing the Y amaha CR W4261t Drive MASTER/SLA VE settings Before you install the CR W4261t in your computer , you must make the MASTER/SLA VE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CR W4261t driv e.
Chapter 2 - Installing the Yamaha CRW4261t Drive 6 Setting the CR W4261t as the MASTER As shown in the diagram at the right, insert the jumper pin into the right edge of the jumper switch. Note: If only the CRW4261t will be connected to the IDE interface connector , connect the CRW4261t to the end of the connector .
Chapter 2 - Installing the Yamaha CRW4261t Drive 7 Installing the CR W4261t drive The following steps will dif fer slightly depending on the type of com- puter you are using. For details on remo ving the cover from your computer , and installing or removing internal de vices, refer to the manual for your computer .
Chapter 2 - Installing the Yamaha CRW4261t Drive 8 3. Y our hands or body may be holding a char ge of static elec- tricity . T ouch a metallic portion of the chassis or power supply to release any suc h charge. 4. Remove the fr ont cover of a vacant half-height drive ba y .
Chapter 2 - Installing the Yamaha CRW4261t Drive 9 6. Connect the IDE interface connector . Connect the 40-pin IDE interface connector to the IDE interface located on the rear panel of the CR W4261t driv e. Position the connector so that the colored line is at pin 1 (your lower right).
Chapter 2 - Installing the Yamaha CRW4261t Drive 10 A UDIO cable 8. Connect the power suppl y cable . Connect the +12V and +5V 4-pin power cable to the po wer supply interface located on the rear panel of the CR W4261t drive. The shape of the connector makes it impossible to re verse the connec- tions.
Chapter 2 - Installing the Yamaha CRW4261t Drive 11 9. Tighten the four fastening scre ws securely . 10. Attach the co ver of your computer . 11. Connect the power cable to an A C outlet, and s witch on your computer . Make sure that the LED located on the panel of the CR W4261t drive is lit.
Chapter 3 - Operation 12 Chapter 3 - Operation Front P anel 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray . 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone v olume control This control adjusts the volume le vel of the headphone output.
Chapter 3 - Operation 13 6 Eject button This button is used to open or close the tray . 7 Manual Eject hole This is used to manually eject a disc that cannot be ejected in the nor- mal way . It is for emergency use only . Loading a Disc 1. Press the eject button to open the tra y .
Chapter 3 - Operation 14 Ejecting the Disc If the CR W4261t is powered on: Press the eject button to eject the disc. Note: Y ou cannot eject the disc if the A T API command prohibits the eject operation while the CRW4261t is r eading data. Caution: Be sur e to remove the disc after it is completely ejected.
Chapter 3 - Operation 15 Manual Eject (emer g ency use) Here we explain ho w to eject the disc when it cannot be ejected in the normal way; for example, the po wer is shut off inadv ertently or the loading mechanism fails. This technique should be used only as a last resort.
Troubleshooting 16 T r oubleshooting If CR W4261t is not performing as expected, look up the symptoms in the follo wing table, and take the appropriate correcti ve action. Symptoms Corrective action The power to the CR W4261t is off • Check the DC po wer cable connection.
Appendix 17 Appendix Specifications Specifications are subject to change without prior notice. Interface A T API (E-IDE) Data Capacity 650MB (74 minutes disc) 550MB (63 minutes disc) Record/Read Spe.
Appendix 18 Front P anel Indicator Ke y ● on: green flashing: green — off ❍ on: orange flashing: orange Status ON/DISC READ/WRITE Reset ❍ ➠ — ❍ ➠ — Ready (no disc) ❍ — Insertin.
Y AMAHA CORPORA TION Electronic Systems Division Printed in Japan V007120-0 English: If you have any questions, please contact your dealer or one of the following companies.
デバイスYamaha CRW4261t-NBの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Yamaha CRW4261t-NBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha CRW4261t-NBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha CRW4261t-NBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha CRW4261t-NBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha CRW4261t-NBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha CRW4261t-NBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha CRW4261t-NBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha CRW4261t-NBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
