YamahaメーカーEMX620の使用説明書/サービス説明書
ページ先へ移動 of 18
E Owner’ s Manual Keep This Manual For Future Reference. 1 123 HIGH LOW MONI EFFECT PA D LEVEL –15 +15 –15 +15 01 0 01 0 01 0 2 HIGH LOW MONI EFFECT PA D LEVEL –15 +15 –15 +15 01 0 01 0 3 HI.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
Important 3 EMX620—Owner’s Manual Important Read the following before operating the EMX620 W arnings • Do not allow wate r to enter this unit or allow the unit t o become wet.
4 Important EMX620—Owner’s Manual Operating Notes • U sing a mobile telephone near this unit may induc e noise. I f noise occurs, use the telephone awa y from the unit. • XLR -ty pe connect ors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (–).
Introduction 5 EMX620—Owner’s Manual Introduction Thank you for pur chasing the Y amaha EMX620 P ower ed Mixer . In order to tak e full advantage of the EMX620 and enjoy long and trouble-free operation, read this owner’ s manual carefully , and keep it in a safe place for futur e reference.
6 Front & Rear Panels EMX620—Owner’s Manual Front & Rear Panels Control Panel ■ Channel Section The channel co nt r ols are used to set the EQ, MONI and EFFECT send levels, channel LEVEL, and P AD for each channel.
Control Panel 7 EMX620—Owner’s Manual ■ DIGIT AL EFFECT Section The DIGIT AL EFFECT section is used to turn the built-in digital effects processor on and off and select effects programs. F VOCAL, L. HALL, S. HALL switches These switches are used t o select the effects pro- grams: V OCAL, L.
8 Front & Rear Panels EMX620—Owner’s Manual N LIMITER indicator The LIMITER indicator lights up when the lim- iter circuit, which is designed to pr otect the inter - nal powe r amplifier against exc essive input signals and load mismatches, activates.
Input/Output Panel 9 EMX620—Owner’s Manual Input/Output Panel 1 Hi-Z, Lo-Z (inputs 1–4) These are the input c onnectors for input chan- nels 1 through 4. Both the Hi-Z and Lo-Z input can be used with microphones and, by using the P AD switch, can also be used with line-le vel sourc es, such as synthesiz ers and dr um machines.
10 Front & Rear Panels EMX620—Owner’s Manual I MAIN—OUTPUT jack The MAIN—OUTPUT jack outputs the MAIN bus signal after the 7-band graphic equalizer and MASTER level co ntrol, and can be connected to the input of a larger mix er , or a more pow erful amplifier , for example.
Rear Panel 11 EMX620—Owner’s Manual Rear Panel 1 POWER switch The PO WER switch is used to turn on and off the powe r to the EMX620. B SPEAKERS A & B jacks The SPEAKER A & B phone jacks output the main signal from the internal pow er amplifier and are used to c onnect speakers.
12 Front & Rear Panels EMX620—Owner’s Manual Hookup Example B — SPEAKERS — A Headphones Larger mixer or Amplifier Hi-Z Lo-Z Hi-Z Lo-Z Hi-Z Lo-Z Hi-Z LINE Lo-Z 1 LINE 2 INST 1 INST EFFECT OUT FOOT SW 2 PHONES MAIN MONITOR INPUT TO MAIN OUTPUT 11 22 T APE IN AUX IN REC OUT 88 *2 *1 *1.
Basic Operation 13 EMX620—Owner’s Manual Basic Operation Connecting Sour ces Before c onnecting any microphones or instru- ments, make sure that the EMX620 and an y other applicable equipment is turned off. Also make sure that the LE VEL control on each EMX620 input channel, and the MAIN MASTER and MONI MASTER contr ols are turned down.
14 Troubleshooting EMX620—Owner’s Manual T roubleshooting The following table describes the possible malfunctions of this demvice, and the appropriate actions to be taken in eac h case. Prob lem Cause Action Sound is no longer out- put from the speakers .
Specifications 15 EMX620—Owner’s Manual Speci fi cations ■ General Speci fi cations For E uropean M odel Pur chaser/U ser Information specified in EN55103-1 and EN55103-2. Inrush C ur rent: 23A Conformed En v ironment: E1, E2, E3 and E4 Maximum output po wer 135 W/8 Ω @0.
16 Specifications EMX620—Owner’s Manual ■ Input Speci fi cations ■ Output Speci fi cations • PHONE J ACKS are unbalanced. • 0 dB= 0.775 Vrms, 0 dBV= 1 Vrms.
Block & Level Diagrams 17 EMX620—Owner’s Manual ■ Block & Level Diagrams +30dB +20dB +10dB 0dB – 10dB – 20dB – 30dB – 40dB – 50dB +30dB +20dB +10dB 0dB – 10dB – 20dB – 30.
YAMAHA CORPORATION V474530 R1 1 IP 20 Pro Audio Division, #18/3 P.O. Box 3, Hamamatsu, 430-8651, Japan Printed in Taiwan.
デバイスYamaha EMX620の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yamaha EMX620をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha EMX620の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha EMX620の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha EMX620で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha EMX620を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha EMX620の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha EMX620に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha EMX620デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。