YamahaメーカーMV6の使用説明書/サービス説明書
ページ先へ移動 of 20
MIXER Owner’ s Manual Thank you f or purchasing the Y AMAHA MV12/6 Mix er . The MV12/6 mix er is designed to pro v ide the user with an ideal balance of operabilit y , functionality , and simplicity .
MV12/6 — Owner’ s Manual FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
MV12/6 — Owner’ s Manual Important Read the following before operating the MV12/6 Important 1 W arnings • Do not place a container with liquid or small metal objec ts on t op of this unit. Liquid or metal objects inside this unit are a fir e and electrical shock hazard.
MV12/6 — Owner’ s Manual 2 MV12/6 Features • The MV12/6 offers 12 input channels that can be mix ed into stere o, monaural, or t o four group outputs. • A MONITOR jack offers easy c onnection to a sub amp for monito r- ing. I t allows monit oring of the main ster e o output, T APE IN inpu t and the signals from groups 1-2, 3-4.
MV12/6 — Owner’ s Manual Front & Rear Panels 3 q y tt o u e ii r r w Channels 1-8 (Monaural) Channels 9-12 (Stereo) Response [dB] +5 +10 +15 – 15 – 10 – 5 0 Frequency [Hz] 10k 1k 100 20k.
MV12/6 — Owner’ s Manual 4 Front & Rear Panels y EFFECT Control Controls the level of the signal sent from each channel to the EFFECT bus. This control is located aft er the channel fad er so its level will also be affected by the channel fader setting.
MV12/6 — Owner’ s Manual Front & Rear Panels 5 q i !5 w !3 !0 er !1 !4 !2 t o y u q ST Master Fader Controls the level of the signal that is sent to the ST OUT jacks. w MONO Control Controls the level of the signal (the monaural sig nal that is formed by c ombining the signals from the STEREO bus) that is sent to the MONO OUT jack.
MV12/6 — Owner’ s Manual 6 Front & Rear Panels u DIGIT AL EFFECT • PROGRAM Select Switch Selects a program from the built-in digital effects. VOCAL ECHO 1 VOCAL ECHO 2 VOCAL ECHO 3 VOCAL ECHO 4 VOCAL REVERB 1 VOCAL REVERB 2 VOCAL REVERB 3 VOCAL REVERB 4 • P ARAMETER Control Controls paramet ers (effect level, speed, etc.
MV12/6 — Owner’ s Manual Front & Rear Panels 7 q INPUT Jacks (CH 1-8) Both balanced XLR typ e and E uro-block c onnectors ar e supplied. • XLR T ype (1:Ground, 2:Hot, 3:Cold) • Euro-block connectors ( : Hot, : Cold, G: Ground) U se Input Select Switch to mat ch the input to the type of mic or dev ice connected t o the INPUT jack.
MV12/6 — Owner’ s Manual 8 Front & Rear Panels t SEND Jacks • AUX1, AUX2 These are impedanc e balanced phone typ e output jacks with a nominal output/impedance of +4dB/ 600 Ω . The A UX1, 2 bus sig nals ar e output from the ir respectiv e jacks.
MV12/6 — Owner’ s Manual Front & Rear Panels 9 !1 MONO OUT Jack This signal is the monaural mix of the STEREO bus’ s stereo signal. Its level is co ntrolled with the MONO control. T wo ty pes of j acks ar e pro vided; balanced XLR typ e and E uro-block c onnectors.
MV12/6 — Owner’ s Manual 10 Front & Rear Panels ■ Changing the connector panel’ s location. The mixer allo ws attachment of the connecto r panel to either the rear or to the t op-side of the mixer t o pro vide optimum location of the connectors when installing the unit.
MV12/6 — Owner’ s Manual About the Accessories 11 About the Accessories Euro-block Connectors If you decide to use E uro-block connectors, please use the supplied connectors and attac h as shown in the illustration below . q T urn the PO WER switch OFF .
MV12/6 — Owner’ s Manual ST OUT AUX 1 SEND AUX 2 (PRE) SEND INSERT IN INSERT OUT PHONES TAPE IN REC OUT INPUT MONO OUT 12 Applications Applications Example 1) Basic Setup Procedure q Connect line input devices or micro pho nes t o the INPUT jacks and connect a pow er amp , that is connected t o the main sp eake rs, to the ST OUT J a cks.
MV12/6 — Owner’ s Manual ST OUT AUX 1 SEND AUX 2 (PRE) SEND PHONES TAPE IN REC OUT INPUT GROUP OUT 1 2 3 4 Applications 13 Example 2) Banquet Room Setup Using Independent Speakers .
MV12/6 — Owner’ s Manual Frequency response 20Hz — 20kHz +1dB, -3dB @+4dB, 600 Ω (INPUT GAIN Control at minimum level) T otal harmonic distortion <0.
MV12/6 — Owner’ s Manual Supplement 15 ■ Input Specifications Input Input GAIN Input Nominal Input level Connector type connectors Select Switch Control impedance impedance Sensitivity *1 Nominal Max. bef ore clipping MIC (+48V) -60 -80 dB (0.078mV) -60 dB (0.
MV12/6 — Owner’ s Manual 16 Supplement 192 308 482 18.7 Units: mm Dimensions.
MV12/6 — Owner’ s Manual Supplement 17 CH INPUT 1~4ch INPUT [-60~+10dB] INSERT OUT [0dB] PAD HA GAIN [-60dB~-16dB] [-34dB~+10dB] [0dB] Lo Mid Hi 3-Stage EQ PEAK Ch.
Y AMAHA CORPORA TION Pro Audio & Digital Musical Instrument Division P .O. Box 3, Hamamatsu, 430-8651, Japan V639260 R2 1 CP 20 NP Printed in T aiwan.
デバイスYamaha MV6の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yamaha MV6をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha MV6の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha MV6の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha MV6で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha MV6を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha MV6の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha MV6に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha MV6デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。