Yard Machinesメーカー690の使用説明書/サービス説明書
ページ先へ移動 of 20
YARD MACHINES OWNER'S GUiD Model Series 690 Thru 699 HYDROSTATIC LAWN TRACTORS IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion e.
& IMPORTANT OPERATION PRACTICES THIS SYMBOL POINTS OUT IMPORTANTSAFETYIN ;TRUCTIONS WHICH, IF NOT FOLLOWED,COULD ENDANGER THE PERSONAL SAFETYAND/OR PROPERTY OF YOURSELF AND O-HERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ,_IL ATTEMPTING TO OPERATE YOUR UNIT.
4. Never carry children, even with the blades off. They may fall off and be seriously injured or interfere with the safe machine oper- ation. 5. Never allow children under 14 years old to operate the machine. Children 14 years and over should only operate machine under close parental supervision and proper instruction.
UNPACKING TO REMOVE UNIT FROM CRATE 1. Remove all screws from the top of the c_ate using a 1/4" hex head socket or a flat blade scl ewdriver. 2. To remove ends, grasp top board on the end, and pull towards you in a downward motion. 3. Set panel aside to avoid tire punctures.
BATTERY IDENTIFICATION Type "A" Type "B" Compare the battery in your lawn tractor (located under the seat) with the illustration above. Type "A" batteries are activated and are ready to use. Type "B" batteries must be filled with battery fluid (acid) and charged before they are put into service.
! FIGURE 2. Screws 7 _- ATI'ACHING THE SEAT Remove the four screws which secure the seat to the seat pivot bracket. Turn the seat around and place in position against the seat pivot bracket, lining up the slotted holes in the pivot bracket with the holes in the seat.
,ck Hanger _-_ L "IGURE 4. ustable/ Positive Terminal (Inside Rubber Boot) il U Q / Negative Cable Negative Battery FIGURE 5. Terminal Compartment Battery Battery Reinforcement FIGURE 6.
CONTROLS IGNITION SWITCH The ignition switch is located on the dashlo3ard. The engine is started by turning the key to the ST _,RT posi- tion. When the engine is running, leave the {ey in the ON position. To stop the engine, turn the _ey to the OFF position.
IELIEF VALVE hydrostatic relief valve is provided so the unit can be noved without the engine running. The lever which Iperates the relief valve is located on the console. See igure 9. o operate the relief valve, place the hydrostatic con- rol lever in neutral, release the parking brake, push he lever forward and to the right to lock.
STARTING THE ENGINE IMPORTANT: This unit is equipped with a safety interlock system for your protection. The I: urpose of the safety interlock system is to prevent tl_e engine from cranking or starting unless the clutoh-bu ake pedal is depressed and the lift lever is in the BLA 3ES OFF position.
If adjustment is necessary, follow these steps: 1. Raise bothrear wheels off the ground by placing blocks under the rear frame. 2. Remove the transmission panel by removing the parking brake knob and truss machine screws. 3. Loosen the hex jam nut on the speed selector adjusting rod.
BRAKE ADJUSTMENT (See figure 13) The brake is located by the right rear wheel ir side the frame. The brake has been set at the factoly to the proper clearance. During normal operation of this machine, the brakes are subject to wear and will require periodic examination and adjustment.
MAINTENANCE WARNING: Disconnect the spark plug wire and ground against the engine before performing any adjustments, repairs or maintenance. TROUBLE SHOOTING Refer to the chart on page 17 for trouble shooting engine problems. HYDROSTATIC TRANSMISSION COOLING The hydrostatic transmission is cooled by the oil, fan and fins.
t B .I t (118" LessThan A) -I FIGURE 17. CUTTING BLADES A. Removal for Sharpening or Replacemen & WARNING: Be sure to disconnect and ground the spark plug wire(s) and remove ignition key before working on the cutting blade to prevent accidental engin.
BATTERY FAILURES Some common causes for battery failure are: incorrect initial activation, lack of water, adding chemicals other than water after initial activation, undercharging, over- charging, corroded connections, freezing. These failures do not constitute warranty.
7. Disconnect the stabilizer plate fromthe _tabilizer shaftassembly by removing the hairpin I:lips and flatwashers and sliding outthe rod. Refer to figure 12. 8. Disconnect the six deck links by remoJing the hairpin clipsand flatwashers. 9. Place the lift lever in the BLADES OFF pc sition.
6. Store unit in a clean, dry area. Do not store next to corrosive materials, such as fertilizer. NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.
OPTIONAL EQUIPMENT At the time of manufacture {_f lawn tractor, the following optional equipment is available. NOTE: These lawn tractors are not designed for ground-engaging equipment (tillers, plows, etc.
USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY, °oo o L_Ln L_Ln SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE 15 ° T"- WA R N i N Ge._a_4_q_4_4_4_t _AA_AAAAA VVT_VVVV_ Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet).
Copy the information from your model plate here: (Located Under The Seat) N[]INSININININSININ % Have your YO_./ iP model number available when you call Control Wire 18.5" Control Wire 35" Lg. Front Hub Cap (Black) + Rear Wheel Cover (Gray)+ Front Wheel Bearings (Plastic ! Bearinqs (Ball Bearin,qs) Fuse 7.
デバイスYard Machines 690の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yard Machines 690をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYard Machines 690の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yard Machines 690の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yard Machines 690で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yard Machines 690を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYard Machines 690の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yard Machines 690に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYard Machines 690デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。