Yard-ManメーカーLT31の使用説明書/サービス説明書
ページ先へ移動 of 20
Operator’ s Manual L T31 2-Cycle Petr ol T rimmer IMPORT ANT : Read safety rules and instructions carefully befor e operating equipment. PRINTED IN U.
2 T ABLE OF CONTENTS Content P age Important Safe Operation Practices ............................................................... 3 Know Y our T rimmer ........................................................................................ 6 Assembling Y our T rimmer .
3 This Symbol Points Out Important Safety Information Which, If Not Followed, Could Endanger The Personal Safety And/or Property Of Y ourself And Others. Read And Follow All Instructions In This Manual Befor e Attempting T o Operate Y our Cultivator .
WHILE OPERA TING • Never start or run the unit inside a closed room or building. Breathing exhaust fumes can kill. Operate this unit only in a well ventilated area outdoors. •W ear safety glasses or goggles and ear/hearing protection when operating this unit.
5 SYMBOL MEANING • THROWN OBJECTS CAN CAUSE SEVERE INJURY W ARNING: Keep clear of blower outlet. Never point the blower at yourself or others. Objects can be thrown fr om blower .
6 SECTION 2: KNOW Y OUR TRIMMER Cutting Head Guard Fuel Cap Throttle Control D-handle Cutting Head Shaft Grip Primer Bulb Choke Lever Air Filter/Muffler Cover Spark Plug Shaft T ube Starter Rope Grip .
SECTION 3: ASSEMBLING Y OUR TRIMMER 7 INST ALLING THE CUTTING HEAD GUARD W ARNING: To avoid serious personal injury , never operate the trimmer without the cutting head guard in place. 1. Place the cutting head guar d onto the shaft tube above the clamp assembly , Figure 3.
SECTION 4: OPERA TING Y OUR TRIMMER 8 W ARNING: Petr ol is extremely flammable. Ignited vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the ar ea.
FIGURE 7 ST ARTING INSTRUCTIONS W ARNING: Operate this unit only in a well ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area . W ARNING: A void accidental starting. Make sure you ar e in the starting position when pulling the starter rope, Figur e 7.
For best results, tap the Bump Head™ on bar e ground or hard soil. If line r elease is attempted in tall grass, the engine may stall. Always keep the trimming line fully extended. Line release becomes mor e difficult as the cutting line becomes shorter .
11 SECTION 5: MAINT AINING Y OUR TRIMMER FIGURE 11 Spring Bump Knob LINE INST ALLA TION This section covers both Split-Line™ and standard single line installation. Always use original equipment 2.03 mm (0.080 inch) r eplacement line. Line other than specified may make the engine overheat or fail.
12 FIGURE 20 FIGURE 16 FIGURE 17 NOTE: The spring must be assembled on the inner reel before reassembling the cutting attachment. 14. Hold the inner reel in place and install the bump knob by turning clockwise. Tighten securely . Holding Slots Single Line Installation 6.
AIR FIL TER MAINTENANCE Removing the Air Filter/Muffler Cover W ARNING: To avoid serious personal injury , always turn the unit off and allow it to cool before you clean or perform any maintenance on it. 1. Place the choke lever in Position 2 , Figur e 21.
CAUTION: Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder . 4. Install a corr ectly gapped spark plug in the cylinder head. Tighten by turning the 5/8 in. socket clockwise until snug. If using a torque wr ench torque to: 12.
15 NOTE: If exhaust gasket is torn or damaged, replace with a new gasket before reassembling muffler . 4. Using a small flatblade screwdriver , carefully pry up the spark arrestor fr om the recessed hole, Figur e 29. Remove the spark arrestor fr om the muffler .
CLEANING THE UNIT W ARNING: To avoid serious personal injury , always tur n the unit off and allow it to cool before you clean or perform any maintenance on it. • Use a small brush to clean off the outside of the unit and to keep the air vents free of obstructions.
ENGINE WILL NOT ST ART CAUSE A CTION Empty fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fill fuel tank with pr operly mixed fuel Primer bulb wasn't pr essed enough . . . . . . . . . . . . . . . .Press primer bulb fully and slowly 10 times Engine flooded .
ENGINE* Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9: NOTES 19.
OPERA TOR’S MANUAL P ART NO. 769-00828 7/03 PRINTED IN THE USA SECTION 9: NOTES Cont....
デバイスYard-Man LT31の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Yard-Man LT31をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYard-Man LT31の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yard-Man LT31の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yard-Man LT31で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yard-Man LT31を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYard-Man LT31の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yard-Man LT31に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYard-Man LT31デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
