Yazoo/KeesメーカーZKH52251の使用説明書/サービス説明書
ページ先へ移動 of 19
1 MANUAL NO. 102936IR PRINTED IN USA COMMERCIAL MOWERS OPERA T OR’S MANUAL FOR: MODELS: ZKH52221 ZKH52251 ZKH61221 ZKH61251 700-800 P ARK A VE. BEA TRICE, NEBRASKA U.
PRINTED IN USA 2 MANUAL NO. 102936IR Congratulations on the purchase of your Kees mower . This manual has been prepared for the owners and operators of the ZT MAX™ 52" and 61" commercial mowers. Read, under- stand and follow the saftey and operating instructions.
3 MANUAL NO. 102936IR PRINTED IN USA T ABLE OF CONTENTS SAFETY : 1 . Training 2. Preparation 3. Operation 4 . T ransport ation 5. Maintenance SETUP AND ADJUSTMENTS: 1. Park brake 2. Cutting height 3. Mower deck leveling 4. Mule drive belt tension 5.Throttle lever tension 6.
PRINTED IN USA 4 MANUAL NO. 102936IR SAFETY TRAINING: 1. Read this manual carefully and question your dealer if something is not clear . 2. Be thoroughly familiar with the controls and proper use of the equipment. 3. Never allow children, teenagers, or people unfamiliar with these instructions to use the mower .
5 MANUAL NO. 102936IR PRINTED IN USA SAFETY TRANSPORT A TION: Use a heavy duty trailer to haul mower . Set park brake, turn of f fuel valve and strap mower to trailer . NOTE: Park brake will not hold mower in place when transporting. Be sure to tie down the mower to the trailer .
PRINTED IN USA 6 MANUAL NO. 102936IR ADJUSTMENTS P ARK BRAKE: 1. S top engine and remove key . Release p ark brake and measure the length of the spring. The distance between the washers on each end of the spring should be 2-7/8" (See Fig 2 ). 2. If adjustment is needed, loosen the nut below the spring.
7 MANUAL NO. 102936IR PRINTED IN USA ADJUSTMENTS MULE DRIVE BEL T TENSION: 1. S top engine and remove the key . 2. Check to make sure the bolt head in the spring loaded idler pulley , on the left side of the engine deck is positioned between the two alignment holes in the left support plate (See Fig 4).
PRINTED IN USA 8 MANUAL NO. 102936IR Figure 5A Figure 5B 5. If adjustment is necessary , loosen the nut against the yoke. Apply slight rearward pressure to the motion control lever and turn the head of the adjustment bolt in the proper direction until the lever is centered in the neutral slot.
9 MANUAL NO. 102936IR PRINTED IN USA ADJUSTMENTS MOTION CONTROL LINKAGE ADJUSTMENT : 1. This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.
PRINTED IN USA 10 MANUAL NO. 102936IR OPERA TING INSTRUCTIONS NOTE: T o begin motion the operator must be in the seat and the brake disengaged before the levers can be moved from the neutral slots or the engine will kill. By moving the levers an equal amount forward or back the mower will move in a straight line in that direction.
11 MANUAL NO. 102936IR PRINTED IN USA OPERA TING INSTRUCTIONS S T ARTING AND OPERA TION: 1. Operator must be sitting in the seat. Engage park brake, blades off and place the motion control levers in the neutral slots. (See figure 6) 2. Adjust throttle to 1/2 and set choke (if needed) turn key and release as soon as engine starts.
PRINTED IN USA 12 MANUAL NO. 102936IR MAINTENANCE 7. Engine oil: Change oil to manufacturers specifications. S top engine and remove key . Drain oil when engine is warm. Thoroughly clean around cap before removing. Remove oil drain cap from the end of drain hose located at the right rear of unit allow to drain and replace drain cap.
13 MANUAL NO. 102936IR PRINTED IN USA 13. Fuel filter: Replace annually or as needed. 14. Hydraulic filter and oil: Change every 500 hours or yearly . S top engine and remove key . T ilt seat forward and clean around the filter and the fittings under the hydraulic tank.
PRINTED IN USA 14 MANUAL NO. 102936IR.
15 MANUAL NO. 102936IR PRINTED IN USA TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES Engine won’t start Mower will not move or moves slowly or hard 1. Blade switch on. 2. Drive levers not in the neutral slots. 3. Operator not in seat. 4. Park brake disengaged.
PRINTED IN USA 16 MANUAL NO. 102936IR WIRING DIAGRAM.
17 MANUAL NO. 102936IR PRINTED IN USA SERVICE RECORD DESCRIPTION OF WORK DONE DA TE SERVICE DONE BY.
PRINTED IN USA 18 MANUAL NO. 102936IR.
19 MANUAL NO. 102936IR PRINTED IN USA 10. Battery: Check every 25 hours. Check electrolyte level. If needed fill to the full line marked on the side of the battery . Fill with distilled water . Do not try starting the engine with a weak battery . Recharge or replace the battery .
デバイスYazoo/Kees ZKH52251の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yazoo/Kees ZKH52251をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYazoo/Kees ZKH52251の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yazoo/Kees ZKH52251の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yazoo/Kees ZKH52251で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yazoo/Kees ZKH52251を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYazoo/Kees ZKH52251の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yazoo/Kees ZKH52251に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYazoo/Kees ZKH52251デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。