ZotacメーカーZBOX EN860の使用説明書/サービス説明書
ページ先へ移動 of 24
1 ZOT AC ZBOX ZO T A C ZBO X User’ s Manual No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or.
2 ZOT AC ZBOX T a ble of Contents Product specications -------------------------------------------------------------------------- 3 Safety information ----------------------------------------------.
3 ZOT AC ZBOX Product specications q Microprocessor support v Intel CPU Core I5-4210U Processor q Operating systems: v Supports Windows 7 x86/x64 and Windows 8/8.1 x86/x64 q System Memory support v 2 204-pin SO-DIMMs DDR3L 1866/1600/1333 (1.35V) v Up to 16 GB of memory q USB Ports v 4 USB 3.
4 ZOT AC ZBOX Safety inf or mation Y our ZOT AC ZBOX is designed and tested to meet the latest standards of safety for information technology equipment. However , to ensure your safety , it is important that you read the following safety instructions.
5 ZOT AC ZBOX W elcome Congratulations on your purchase of the ZOT AC ZBOX. The illustration below displays the package contents of your new ZOT AC ZBOX.
6 ZOT AC ZBOX Getting to know y our ZOT AC ZBO X F r ont view Refer to the diagram below to identify the components on the front of the ZBOX 1. Headphone/Audio Out jack The stereo headphone jack (3.5mm) is used to connect the system’s audio output signal to amplied speakers or headphones.
7 ZOT AC ZBOX Rear view Refer to the diagram below to identify the components on the back of the system. 1. WiFi antenna connector The WiFi antenna connector supports the included WiFi antenna.
8 ZOT AC ZBOX BIOS settings of specic functions The ZOT AC ZBOX has some specic functions that can be enabled or disabled in the BIOS settings, such as LED indicator , and IR receiver . How to disable the ring LED indicator 1. T urn on the ZBOX mini-PC and press <Delete> to enter the BIOS SETUP UTILITY.
9 ZOT AC ZBOX How to disable the integ rated IR receiver 1. Use the arrow keys to navigate to Features > OnBoard Device Control , and select CIR Controller . 2. Press <Enter> and select Disabled . Enabled : enable the internal IR receiver (default) Disabled : disable the internal IR receiver 3.
10 ZOT AC ZBOX Installing har dware inside the ZOT AC ZBO X Before installing hardware, please follow the instructions below to remove the cover of your ZOT AC ZBOX. 1. Remove the two thumb screws highlighted below . 2. Gently slide the cover off as shown below .
11 ZOT AC ZBOX 2. Gently press down on the memory module until it locks into place by the arms of the memory slot. Remo ving a memor y module 1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory module outwards, as shown in the image below , to release the memory module.
12 ZOT AC ZBOX Installing a har d disk 1. Locate the 2.5-inch SA T A hard disk or SSD and the hard disk bracket. 2. Attach the hard disk or SSD to the hard disk bracket.
13 ZOT AC ZBOX 3. Insert the hard disk or SSD into the slot at a 45 degree angle and gently slide into the SA T A connector. 4. Install the thumb screw .
14 ZOT AC ZBOX Setting up your ZO T AC ZBO X Please connect your peripherals before using your ZOT AC ZBOX 1. Connecting the WiFi antenna Connect the WiFi antenna to the WiFi antenna connector . 2. Connecting the optical S/PDIF output Connect a digital audio device via optical S/PDIF output.
15 ZOT AC ZBOX 5. Connecting to a DVI or VGA display Connect one end of a DVI/VGA cable to an HDTV or monitor , and the other end to the DVI port on the system rear panel.
16 ZOT AC ZBOX P ositioning your ZO T AC ZBO X Do not position the ZOT AC ZBOX where the ventilation holes are covered. T o guarantee proper use, leave 4 inches (10 cm) spacing in front of the ventilation holes.
17 ZOT AC ZBOX Installing driv er s and softwar e Installing an operating system The ZOT AC ZBOX does not ship with an operating system preinstalled. The user must install the operating system before the ZOT AC ZBOX can be used.
18 ZOT AC ZBOX Each driver must be installed individually to ensure proper operation of the ZOT AC ZBOX. 3. Select the driver you want to install. The driver installer should launch. 4. Follow the onscreen instructions to install the drivers. 5. Restart the system.
19 ZOT AC ZBOX Using a dynamic IP (PPPoE connection) 1. Repeat Step 1-3 in the previous section. 2. Select “Obtain an IP address automatically” and click “OK”. 3. Click “Create a new connection” to start the NEW Connection Wizard. 4. Click “Next”.
20 ZOT AC ZBOX NVIDIA 2D Sur round Introduction By using NVIDIA 2D Surround T echnology to support multi-display 2D game, the visual experience truly comes to life. Setting up NVIDIA 2D Sur r ound T echnology Follow the instructions below to set NVIDIA 2D Surround.
21 ZOT AC ZBOX 2. Select “ 1 x 3 ” in “ T opology ” box, and check the boxes in “ Displays ”. When the box “ Surround is enabled ” displays, the Surround setting is completed.
22 ZOT AC ZBOX.
23 ZOT AC ZBOX.
24 ZOT AC ZBOX 291-MB261-00.
デバイスZotac ZBOX EN860の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zotac ZBOX EN860をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZotac ZBOX EN860の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zotac ZBOX EN860の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zotac ZBOX EN860で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zotac ZBOX EN860を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZotac ZBOX EN860の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zotac ZBOX EN860に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZotac ZBOX EN860デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。