Black BoxメーカーIC1001Aの使用説明書/サービス説明書
ページ先へ移動 of 38
JULY 2002 IC135A IC1001A IC1000A IC1002A USB Dir ectors RS-232 CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
1 FCC/IC RFI STATEMENTS FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS This device complies with the requirements of the Code of Federal Regulations listed below: FCC Title 47 CFR, Part 15 Class B for a digital device.
2 USB DIRECTORS RS-232 Warning: Connecting a non-shielded interface cable to this device will invalidate this device’s FCC Certification. This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada.
3 NOM STATEMENT NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
4 USB DIRECTORS RS-232 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como se indique en el aparato. 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
5 TRADEMARKS TRADEMARKS USED IN THIS MANUAL BLACK BOX and the logo are registered trademarks of Black Box Corporation. Pentium is a registered trademark of Intel Corporation. Microsoft, Windows, Windows CE, Windows Me, and Windows NT are registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
6 USB DIRECTORS RS-232 Contents Chapter Page 1. Specifications ......................................................................... 8 2. Introduction ........................................................................ 11 2.1 Overview .......
7 TABLE OF CONTENTS Chapter Page 5. Troubleshooting .................................................................. 26 5.1 Using USB with Windows 95 ...................................... 26 5.1.1 Checking for USB Hardware .........................
8 USB DIRECTORS RS-232 1. Specifications System Requirements: Pentium ® class CPU with at least 16 MB RAM and at least one available USB type A (downstream) port, running Windows 95 (at least OSR2), .
9 CHAPTER 1: Specifications Indicators: IC1000A: None; IC1001A, IC1002A, IC135A: (1) Front-mounted tricolor LED Connectors: All models: (1) USB Type B female (front-mounted on IC1001A, rear-mounted on.
10 USB DIRECTORS RS-232 Weight: IC1000A: 1.6 oz. (45 g); IC1001A: 12 oz. (340 g); IC1002A, IC135A: 1 lb. (0.5 kg).
11 CHAPTER 2: Introduction 2. Intr oduction 2.1 Overview The USB Directors RS-232 are intelligent expansion modules that connect to a PC or server running Microsoft ® Windows ® 95, 98, 98 SE, or 2000, Windows CE ® , Windows Me ® , or Windows NT ® 4.
12 USB DIRECTORS RS-232 2.2 The Complete Package In addition to the USB Director RS-232, you should have received: • (1) 1-m (3.3-ft.) USB cable. • (1) CD with driver and utility software. • This manual. If anything is missing or damaged, please contact Black Box immediately at 724-746-5500.
13 CHAPTER 3: Installation 3. Installation 3.1 Installing the Hardware Plug the Type A end of the included 1-m (3.3-ft.) USB cable into the USB port located in the back of your PC or into an available USB port on a standard USB hub or USB switch. Plug the Type B end of the USB cable into the back of the USB Director RS-232.
14 USB DIRECTORS RS-232 Plug your RS-232 device(s), or the cables running to them (not included), into the USB Director RS-232’s DB9 male serial connector(s). Any device or cable that can be attached directly to a DB9 serial port on a PC can be attached to the DB9 connector(s) on a USB Director RS-232.
15 CHAPTER 3: Installation 3.2 Installing the Software Drivers These installation instructions are for installing the USB Director RS-232 software from CD. NT users will not be prompted and will need to locate the driver by double- clicking on their CD-ROM drive.
16 USB DIRECTORS RS-232 3. When the Select Other Location dialog box appears, type “X:Win95” (where “X” is the drive letter of your CD-ROM drive) and click “OK.” 4. Confirm that Windows has found the correct driver location and click “Finish.
17 CHAPTER 3: Installation 2. If you haven’t already done so, follow the hardware-installation instructions in Section 3.1 . After connecting the USB cable, the Add New Hardware Wizard should appear. Click “Next.” 3. Select “Search for the best driver for your device” and click “Next.
18 USB DIRECTORS RS-232 3.2.3 W INDOWS NT Because Microsoft does not support USB in NT4.0, we supply a USB stack that will be installed along with the necessary drivers. NOTE You must install the drivers using an account that has administrative privileges! To install the USB stack and USB Director RS-232 drivers, either: 1a.
19 CHAPTER 3: Installation Once the driver installation program has begun, follow the on-screen instructions. 3a. If you are installing drivers for the first time: An Information dialog box informs you that the installation was successful. After clicking “OK,” the installation is complete.
20 USB DIRECTORS RS-232 If you haven’t already done so, follow the hardware- installation instructions in Section 3.1 . When that’s finished, your new communication ports, numbered sequentially following the existing ports in your system, are ready.
21 CHAPTER 3: Installation 5. Select “Specify a location” and click “Next.” 6. Type in “X:Win2k” (where “X” is the drive letter of your CD-ROM drive)and click “OK.” 7. Confirm that Windows is pointing to X:Win2k (where “X” is the drive letter of your CD-ROM drive).
22 USB DIRECTORS RS-232 4. Operation Once you finish installing the hardware and software of the USB Director RS-232, it will operate continuously without requiring further intervention on your part.
23 CHAPTER 4: Operation • It lights green to indicate that the USB Director RS-232’s serial ports are successfully set up and the unit is operating normally, but there’s not currently any data activity. 4.2 Using the Edgeport Utility Program 4.2.
24 USB DIRECTORS RS-232 2. Allows you to configure how COM ports will be assigned. The driver supports COM-port number assignment in two ways: 1. Assigning COM ports based on units’ serial numbers.
25 CHAPTER 4: Operation When using this mode, units are identified not by their serial number, but by a 2- to 7- digit number that identifies which USB port they are plugged into. After changing this setting, you will need to reboot before the change takes effect.
26 USB DIRECTORS RS-232 5. T r oubleshooting 5.1 Using USB with Windows 95 If you’re having difficulty installing or operating your USB Director RS-232 in a Windows 95 system, check the revision level of your copy of Windows 95. If you are using Windows 95 OSR2.
27 CHAPTER 5: Troubleshooting After installing USB Support from your Microsoft Windows 95 OEM system disk, check your Device Manager again. If the two devices are not present or Windows Plug & Play does not autodetect the USB Director RS-232, try the following: 1.
28 USB DIRECTORS RS-232 5.1.2 D ETERMINING THE L EVEL OF USB S UPPORT If you have an earlier version of Windows 95 than OSR2.1, you will need to upgrade to a more recent version of Windows. Otherwise, to determine if your system supports USB, take the following steps: 1.
29 CHAPTER 5: Troubleshooting 5.1.3 C HECKING FOR F ULL USB S UPPORT IN THE D EVICE M ANAGER To determine whether the Windows 95 Device Manager fully supports USB, take the following steps: 1. From the main desktop area of Windows, right- click on the My Computer icon and choose Properties to open the System Properties window.
30 USB DIRECTORS RS-232 If you do not see one or both of these devices, go on to Section 5.1.4 . 5.1.4 D ETERMINING W HY S UPPORT I S N OT P RESENT The DETAILS button in the USBREADY program (see Section 5.1.2 ) can help you determine what is preventing USB support.
31 CHAPTER 5: Troubleshooting If the Test Results Details dialog box shows Windows 95 version 4.0.950 or 4.0.950a, these Windows 95 versions do not support the upgrade path to USB. Unfortunately, Microsoft has not provided an upgrade path to OSR2 from earlier of these versions of Windows.
32 USB DIRECTORS RS-232 5.2 Calling Black Box If your USB Director RS-232 seems to be malfunctioning, do not attempt to alter or repair it . It contains no user-serviceable parts. Call Black Box Technical Support at 724-746-5500; the problem might be solvable over the phone.
33 CHAPTER 5: Troubleshooting 5.3 Shipping and Packaging If you need to transport or ship your USB Director RS-232: • Package it carefully. We recommend that you use the original container. • If the shipping is return- or repair-related, include everything you received with the unit when you pack it.
34 USB DIRECTORS RS-232 SOFTWARE RESTRICTIONS If the USB Director RS-232’s software is being used by the U.S. government: Use, duplication, or disclosure by the government is subject to the restrictions set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause of DFARS 52.
NOTES.
NOTES.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 © Copyright 2002. Black Box Corporation. All rights reserved..
デバイスBlack Box IC1001Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Black Box IC1001Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack Box IC1001Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black Box IC1001Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black Box IC1001Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black Box IC1001Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack Box IC1001Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black Box IC1001Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack Box IC1001Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。