Black BoxメーカーIC181Cの使用説明書/サービス説明書
ページ先へ移動 of 17
CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mail order: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.
FOUR POR T RS-232 SERIAL INTERF ACE FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio frequency en.
FOUR POR T RS-232 SERIAL INTERF ACE Contents Chapter Page 1. Specifications...................................................................................................1 2. Introduction ...........................................................
1 CHAPTER 1: Specifications Protocol — Asynchronous Number of Ports — 4 Speed — IC111C: Up to 115.2 Kbps; IC181C: 460.8 kbps and higher Operation — RS-232 Connectors — DB37M on card; (1) 3-ft. (0.9-m) DB37F-to-4x DB25M octopus cable, included Maximum Distance — 50 ft.
2 FOUR POR T RS-232 SERIAL INTERF ACE 2.1 Overview The Four Port RS-232 Serial Interface provides your PC system with four RS- 232 asynchronous ports. Connect to any device that uses the RS-232 protocol, such as modems, data-entry terminals, and plotters.
3 CHAPTER 2: Introduction 2.3 Features Listed below are the special features your Serial Interface offers. • Each port is independently addressable. • Eleven interrupt options, including AT interrupts, for simple integration into existing systems.
4 FOUR POR T RS-232 SERIAL INTERF ACE 2.4 T echnical Description The Four Port RS-232 Serial Interface provides four additional serial ports for terminals, modems, printers, etc.
5 CHAPTER 3: Address Selection NOTE Be sure to set the address selections and jumper options before installation. Each serial port on the Four Port RS-232 Serial Interface occupies 8 con- secutive I/O locations. DIP switch SW4 sets the base address for Port 1, SW3 for Port 2, SW2 for Port 3, and SW1 for Port 4.
6 FOUR POR T RS-232 SERIAL INTERF ACE NOTE Be sure to set the address selections and jumper options before installation. The board contains several jumper straps for each port which must be set for proper operation. 4.1 Port Enable/Disable Each port on the Four Port RS-232 can be enabled or disabled with switch position 8 on the DIP switch.
7 CHAPTER 4: Option Selection Any two or more ports can share a common IRQ by placing the jumpers on the same IRQ setting, and setting the appropriate selections at E1. Consult your particular software for IRQ selection. If no interrupt is desired, remove the jumper.
8 FOUR POR T RS-232 SERIAL INTERF ACE 4.2 Interrupt-Mode Options Jumper E5 selects the interrupt mode for each port. Each port must be set in the correct mode to ensure proper installation. “N” indicates the normal, single interrupt per port mode (Figure 4-2).
9 Set jumper to “S” if you are using more than one Four Port RS-232 Serial Interface in a bus or you wish to remove the pull-down resistor completely for hardware compatibility. NOTE Setting the board in this configuration when it is not accompanied by a pull-down resistor will prevent the ports from triggering an interrupt.
10 FOUR POR T RS-232 SERIAL INTERF ACE IMPOR T ANT You MUST set up the operating system BEFORE you physically install the Card. 5.1 Software Installation If you are installing an ISA adapter in DOS, OS/2 ® , or QNX, please refer to the appropriate directory on one of the Serial Utilities Disks for instructions.
11 CHAPTER 5: Installation 5.2 Hardware Installation The ISA Card can be installed in any of the PC expansion slots. The Card contains several jumper straps for each port that you must set for proper operation. 1. Turn off PC power. Disconnect the power cord.
12 FOUR POR T RS-232 SERIAL INTERF ACE U6 R9 U5 U14 U13 U12 U11 C9 C10 U17 C12 C11 U18 C15 C19 C13 C7 U10 C6 U9 PORT 1 C8 R3 R4 D3 SW3 C5 U8 E4 E5 12 4 M S N M S N R2 D2 C3 U15 + C14 P1 C4 U7 P2 PORT 2 PORT 3 PORT 4 PORT 1 SW4 A9 A3 ON=0 U4 PORT 1 PORT 2 PORT 3 U3 SW2 U2 PORT 4 SW1 U1 C1 C2 E3 PORT 2 E2 PORT 3 E1 PORT 4 R1 1 20 19 37 Y1 U16 P3 E 3.
13 APPENDIX B: T roubleshooting By using the supplied serial utility diskette and following these simple steps, most common problems can be eliminated. 1) Identify all I/O adapters currently installed in your system. This includes your onboard serial ports, controller cards, and sound cards.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 © Copyright 2000. Black Box Corporation. All rights reserved..
デバイスBlack Box IC181Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Black Box IC181Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack Box IC181Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black Box IC181Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black Box IC181Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black Box IC181Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack Box IC181Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black Box IC181Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack Box IC181Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。