Black BoxメーカーPSD-8の使用説明書/サービス説明書
ページ先へ移動 of 17
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.
FCC ST A TEMENT 1 FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio-frequency energy , and if not installed and used properly , that is, in strict accordance with the manufacturer’ s instructions, may cause inter ference to radio communication.
PSD-4 AND PSD-8 2 INSTRUCCIONES DE SEGURIDAD (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
TRADEMARKS 3 TRADEMARKS USED IN THIS MANUAL AS/400 is a registered trademark of International Business Machines Corporation. Any other trademarks mentioned in this manual are acknowledged to be the pr oper ty of the trademark owners.
PSD-4 AND PSD-8 4 1. Specifications Number of Sub-Channels — PSD-4: 4 PSD-8: 8 Channel Configuration — Lowest Priority: Sub-channel 1 Highest Priority: PSD-4: Sub-channel 4 PSD-8: Sub-channel 8 Su.
CHAPTER 2: Introduction 5 2. Introduction The Programmable Sharing Device enables up to 4 (TL304A) or 8 (TL305A) modems or terminals to share a master modem, multiplexor , or computer port in an asynchronous or synchronous multipoint environment. (Asynchronous and synchronous equipment cannot be mixed on the same PSD.
PSD-4 AND PSD-8 6 3. Installation 3.1 Choosing a Site • The PSD must be installed within five feet (1.5 m) of a grounded AC outlet. • The PSD must be within 50 feet (15 m) of the equipment that will be attached to the main channel and each sub-channel.
CHAPTER 3: Installation 7 T able 1. Printed Circuit-Board Switch and Strap Settings Possible Factory Stap Identity Location Settings Setting Function MAIN DCE/DTE switch DTE DTE Determines the PSD’s Main Channel DCE interface as either DTE (straight connection to a modem) or as DCE (straight connection to a computer or terminal).
PSD-4 AND PSD-8 8 Figure 3. The Printed Circuit Boar d of the PSD-4. Figure 4. The Printed Circuit Boar d of the PSD-8..
CHAPTER 3: Installation 9 3.3 System Synchronization A SYNCHRONOUS M ODE Strap the J6 jumper over the ASYNC pins. All attached equipment must be asynchronous. T urn the BIT RA TE rotary switch (BRI) to the correct system speed. No other adjustments to the PSD are necessar y .
PSD-4 AND PSD-8 10 • BIT RA TE rotar y switch: Set BRI to the correct system speed. • EXT . BUFFER: If any of the devices connected to the sub-channels numbered 1 through 4 are set to internal clock, then switch S1 should be ON.
CHAPTER 4: Operation and T roubleshooting 11 4. Operation and T roubleshooting 4.1 Operation T urn on the rear-panel POWER rocker switch. The front-panel POWER LED will light. The PSD operates automatically . Except for manually disabling a sub-channel, you will not need to attend to the PSD.
PSD-4 AND PSD-8 12 Figure 5. The back panels of the PSD-4 (top) and the PSD-8 (bottom). FUSE POWER: Rocker switch to turn AC power on or off 110/220 VAC Selector: Align either 110 or 220 with the arrow. SCREWS: Loosen these screws to take off the cover of the PSD.
CHAPTER 5: T echnical Guide 13 5. T echnical Guide 5.1 Control Signals M AIN C HANNEL C ONTROL S IGNALS RTS (DCD) • In R TS/DCD contention mode: follows R TS (DCD) of the selected sub-channels. • In Data Contention mode: ON if one of the sub-channels R TS (DCD) is ON.
PSD-4 AND PSD-8 14 Figure 6. Main Channel DTE with Sub-Channel DCE. Figure 7. Main Channel DTE with Sub-Channel DTE..
CHAPTER 5: T echnical Guide 15 Figure 8. Main Channel DCE with Sub-Channel DCE. Figure 9. Main Channel DCE with Sub-Channel DTE..
1000 P ark Drive • Lawrence, P A 15055-1018 • 724-746-5500 • F ax 724-746-0746 © Cop yright 1998. Black Box Corporation. All rights reserved..
デバイスBlack Box PSD-8の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Black Box PSD-8をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack Box PSD-8の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black Box PSD-8の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black Box PSD-8で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black Box PSD-8を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack Box PSD-8の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black Box PSD-8に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack Box PSD-8デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。