ACTiメーカーB94の使用説明書/サービス説明書
ページ先へ移動 of 47
Outdoor Mini PTZ Series Hardware Manual B94, B95, B96 , B97 201 4/01/ 07.
w w w .a ct i. co m Hardware Manual 2 T able of Con tents Precautions ............................................................. 4 Safety Instructions .................................................................................... 6 Introduction .
w w w .a ct i. co m Hardware Manual 3 Other Adjustments and Accessories .................. 35 How to Remove / Install the Camera Module ......................................... 35 How to Remove the Camera Module ......................................
w w w .a ct i. co m Hardware Manual 4 Precautions Read these instructio ns Y ou should read all the safety and operati ng instruction s bef ore using this produc t. Heed all warnings Y ou must adhe re to all the warnings on the produc t and in the instruction m anual.
w w w .a ct i. co m Hardware Manual 5 Federal Communic ations Commission Statem ent This equipment has been tested and found to com ply with the limi ts for a class B digital device, p ursuant to Part 15 of the FCC Rules. T hese limits are designed to provide reasonabl e protection against h armful interference in a r esidential installation.
w w w .a ct i. co m Hardware Manual 6 Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachm ents not reco mm ended by the video product manufacturer as they m ay cause hazards.
w w w .a ct i. co m Hardware Manual 7 Introduction The List of Models This hardware m anual contains the following m odels: B94 1.3MP Outdoor Mini PTZ with D/N, Basic W DR, SLLS, 10x Zoom lens B95 2MP.
w w w .a ct i. co m Hardware Manual 8 Package Contents Camera Mounting Scre w Kit Hexagon Screwdri ver Drill T emplate Conduit Gland Cable Gland T erminal Block (for Power) T erminal Block (for DI/DO .
w w w .a ct i. co m Hardware Manual 9 Physical Descri ption Below is an illustratio n of the cam era module. 1) Ethernet Port Connects to a network using an Ethernet c able.
w w w .a ct i. co m Hardware Manual 10 4) Digital Input / Output ( DI/DO) and Audio Input / Outpu t This connector connec ts to digital input or outp ut devices, such as an al ar m trigger , panic button, etc., as well as audio input and output devices, such as m icrophones and speak ers.
w w w .a ct i. co m Hardware Manual 11 Mounting Options There are several m ounting options that you can use to install the cam era. Select t he most suitable solution for your installation environm ent. Mount T ypes Accessories Surface Mount Suitable when mounting the camera directly w alls or ceilings without extra accessories.
w w w .a ct i. co m Hardware Manual 12 Mount T ypes Accessories Straight Wa ll Mount Suitable when mounting the camera on straight walls. PMAX-0308 (L-T ype Wall M ount) PMAX-0101 PMAX-0305 (Heavy Duty Wall Mo unt) V ertical Pole Mount Suitable when mounting the camera on vertical poles.
w w w .a ct i. co m Hardware Manual 13 Other Mounting Accessories Accessories PMAX-0104 (Extension T ube) PMAX-0700 (Junction Box) NOTE: For more inf ormation about the mounting so lutions and access ories, pl ease check the Mounting Accessory Selector in our website ( http ://www .
w w w .a ct i. co m Hardware Manual 14 Installing the Camera on a Surface This section describes the procedures in installing the camera on a fla t surface such as a har d or dropped ceiling and s traight or tilted walls. Before installation, mak e sure the wall or the ceiling can bear m ore than the weight of the cam era.
w w w .a ct i. co m Hardware Manual 15 Step 2: Open the Dome Cover NOTE: T o avoid scratches or leaving f ingerprints on the dom e cover , it is recom mended to retain the plastic covering the dome c over until the cam era is completely installed.
w w w .a ct i. co m Hardware Manual 16 4. Remove the St yrofoam protecting the cam era..
w w w .a ct i. co m Hardware Manual 17 Step 3: Prepare for W aterpro of and Connect th e Cable The camera c omes with two (2) glands used f or waterproof installati on: Cable Gland : For use with an E xterior-grade Ethe rnet cable . Exteri or-grade Eth ernet cables are alread y waterproof.
w w w .a ct i. co m Hardware Manual 18 Waterproof Solution with Conduit on page 22 . Determine the t ype of waterproof solutio n that is appl icable to your ins tallation requirem ents and prepare the necessar y accessories or purch ase extra m aterials.
w w w .a ct i. co m Hardware Manual 19 W aterproof Solution with Naked Cable This section desc ribes the procedures in using the bundled cable gland and an ex terior -grade Ethernet cable. 1. Disassem ble the cable gland as shown belo w: 2. Insert the clam ping nut into the Ethernet ca ble.
w w w .a ct i. co m Hardware Manual 20 4. Attach the cable glan d body to the hole of the camera. Attach to Camera Side Hole Attac h to Camera Bottom Hole 5. If the cable will be rout ed along t he surface , pu ll the network cable through the side conduit hole.
w w w .a ct i. co m Hardware Manual 21 6. Insert the sealing insert with claw into the cab le gland bod y and then a ttach the clam ping nut to complete the cable sol ution.
w w w .a ct i. co m Hardware Manual 22 W aterproof Solution with Conduit This section des cribes the procedures t o waterproof the cablin g connections usin g the bundled conduit gland and flexible c onduit.
w w w .a ct i. co m Hardware Manual 23 2. Disassem ble the bundled conduit gland as sho wn below: NOTE: In this installat ion, the conduit gland b ody can be securel y attached to the m ount kit; therefore the use of lock nut is not necessar y . P lease set the lock nut aside.
w w w .a ct i. co m Hardware Manual 24 5. Insert the sealing insert an d attach it at the end of the flex conduit. 6. Screw the conduit glan d body to the c onduit hole of th e camera . Attac h to Side Conduit Hole Att ach to Bottom Conduit Hole 7. If the cable(s) will be routed along the surface, sk ip this step.
w w w .a ct i. co m Hardware Manual 25 b. Insert the sealing n ut into the conduit g land body and the n attach the clam ping nut as tightly as possible to com plete the cable solution. 8. If only t he network cable will be con nected, connect the network cable to the Ethernet port of the c amera at this point.
w w w .a ct i. co m Hardware Manual 26 10. Connec t the net work cable to the Ethernet port and other cables (if an y) to the correspondin g connectors on th e camera. If necessary , install also the memory card at this point. 11. Align the cam era m odule to the guide on the housi ng.
w w w .a ct i. co m Hardware Manual 27 Step 4: Install the Ca mera to th e Surface Align the camera s crew holes and the cabl e hole (if nec essary) to the holes o n the surface and attach the three (3) su pplied screws ( with rubber) to s ecure the cam era.
w w w .a ct i. co m Hardware Manual 28 2. Remove the plastic co vering the dom e cover . Final installation will look like the illus tration below . Step 6 : Connect to the Netw ork Connect the other en d of the network cable to a switch or injector. Then, connect the s witch or injector to a network or PC and a po wer source.
w w w .a ct i. co m Hardware Manual 29 Other Connections This section desc ribes the procedures in preparing the externa l devices that you can con nect to the camera. The cam era supports DC12V po wer input, Digital Input and Output (DI/DO ) and Audio Input and Output devices using the bu ndled terminal block s.
w w w .a ct i. co m Hardware Manual 30 4. Ti ghten the scre ws of the 1 2V pin and the GND p ins to secure the wire connection . 5. Set the prepared po wer adapter for connection later . Below is an example of a power adapter with an attached term inal block .
w w w .a ct i. co m Hardware Manual 31 Connecting the DI/DO and Audio Devices ( Optional) Depending on your surveillance needs, you ma y conn ect digital input or output or audio input / output devices to y our camera . The cam era comes with on e (1) term inal block for both digita l a nd audio input / output dev ices.
w w w .a ct i. co m Hardware Manual 32 The table below sho ws the DI/DO connectio n specifications: Device DI Connection design TTL - co m patible logic levels V oltage T o trigger (low) Logic level 0: 0V ~ 0.
w w w .a ct i. co m Hardware Manual 33 High Voltage DO Device Connection Even though the cam era provides 12V power , this ma y not be enough for som e high voltage DO devices, such as a cei ling light or a m otor that opens o r closes a gate. In th is case, there is a need to connect an ext ernal relay.
w w w .a ct i. co m Hardware Manual 34 How to Connect Audio Dev ices Audio input / output de vices, such as an acti ve microphone or speak er can b e connecte d to the camera using the supp lied term inal block. Press and hold the orange tab as y ou insert the wire through the pin slot, then release the orange tab to secure the wire.
w w w .a ct i. co m Hardware Manual 35 Other Adjustments and Accesso ries How to Remove / Install the Camera Mo dule How to Remove the Camera Module The camera m odule must be rem oved from the housin.
w w w .a ct i. co m Hardware Manual 36 How to Install the Camera Module 1. Align the camera m odule to the guide s on the hous ing. 2. Ti ghten the three (3) screws to secure th e camera m odule to the housing.
w w w .a ct i. co m Hardware Manual 37 How to Replace the Dome Co ver For more disc rete surveillance needs, th e bundled dom e cover can be replaced with a sm oke, vandal proof c over available for purchase. T o replace the d ome cover , d o the following: 1.
w w w .a ct i. co m Hardware Manual 38 4. Remove dom e cover from the cover housing. 5. Remove the rubb er from the dom e cover . 6. Insert the rubber i nto the replacem ent dome cover .
w w w .a ct i. co m Hardware Manual 39 8. There are 3 in dents on the cover housing; note the indent (a) which is on the center of the extended curve of th e cover . Place the bracket on the c over ho us ing with the arr ow on the bracket aligned to the indent (a).
w w w .a ct i. co m Hardware Manual 40 10. Fit the screw into the spring wire that i s attached to the camera. Note the scre w placem ent as shown below . 11. T here are two (2) screw holes on the bracket, attach the screw to the right screw hole us ing a screwdriver .
w w w .a ct i. co m Hardware Manual 41 How to Insert / Remove a Mem ory Card The camera s upports local video rec ording or saving of snapshots to a m emor y card . NOTE: Supports m icroSDHC and microSDXC c ards. How to Insert the Memory Card 1. Remove the cam era module f rom the housing.
w w w .a ct i. co m Hardware Manual 42 Accessing the Camera Configure the IP A ddresse s In order t o be able t o comm unicate with the camera fr om your PC, both th e camera and the PC have to be within the same network segment.
w w w .a ct i. co m Hardware Manual 43 Double-click on the cam era model name, the default br owser of the PC is automaticall y l aunched and the IP address of the target cam era is already f illed in the address bar of the bro wser .
w w w .a ct i. co m Hardware Manual 44 Use the default I P add ress of a camera: If there is no DHCP server in the give n network, the us er ma y have to assign th e IP address es to both PC and cam era manually to m ake sure they are in the s ame network segment.
w w w .a ct i. co m Hardware Manual 45 Manually adjust the I P ad dresses of multipl e cameras: If there are more than 1 cam era to be used in the same local area network and there is no DHC P server to assign u nique IP addresses to each of them , all of th e cam eras would then have the initial IP address of 192.
w w w .a ct i. co m Hardware Manual 46 Access the Ca mera Now that the cam era and the PC are both ha ving their unique I P address es and are under the same network s egment, it is poss ible to use the Web browser of the PC to access the cam era.
w w w .a ct i. co m Hardware Manual 47 Assum ing that the camera ’ s IP address is 192.168 .0.100 , you can access it by opening the W eb browser and t yping the following address into Web browser ’ s address bar: http://192.
デバイスACTi B94の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ACTi B94をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはACTi B94の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ACTi B94の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ACTi B94で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ACTi B94を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はACTi B94の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ACTi B94に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちACTi B94デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。