Black BoxメーカーRS422/485の使用説明書/サービス説明書
ページ先へ移動 of 29
CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.
1 FCC AND IC RFI ST A TEMENTS FEDERAL COMMUNICA TIONS COMMISSION and INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules.
2 DUAL- AND QUAD-POR T USB HUBS EMC Directive Statement Products bearing the CE Label fulfill the requirements of the EMC directive (89/336/EEC) and of the low-voltage directive (73/23/EEC) issued by the European Commission.
3 NOM ST A TEMENT NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY ST A TEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
4 DUAL- AND QUAD-POR T USB HUBS 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiado.
5 TRADEMARKS TRADEMARKS USED IN THIS MANUAL AT, IBM, and PS/2 are registered trademarks of International Business Machines Corporation. Windows is a registered trademark of Microsoft Corporation. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
6 DUAL- AND QUAD-POR T USB HUBS Contents Chapter Page 1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 1. Specifications Standards: USB version 1.1 Speed: RS-232: Up to 460.8 kbps; RS-422/485: Up to 921.6 kbps Indicators: IC1020A: (5) Status LEDs: (3) USB Enabled; (2) Port Activity; IC1021A, IC1022A:.
8 DUAL- AND QUAD-POR T USB HUBS 2. Introduction 2.1 Overview The USB Hub equips the PC with 2 or 4 USB to RS-232/422/485 or RS-422/485 asynchronous serial ports. It gives you a versatile interface for common serial needs. Three models are available: • The Dual-Port USB Hub (IC1020A) has 2 USB ports to RS-232/422/485 serial ports.
9 CHAPTER 2: Introduction 2.4 Connector Pin Assignments The IC1020A has one USB Type B connector and two DB9 male connectors. The IC1021A and IC1022A have one USB Type B connector and four DB9 male connectors. The pinouts for the DB9 connectors are described in Tables 2-1 and 2-2.
10 DUAL- AND QUAD-POR T USB HUBS 3. Installation 3.1 Operating System Installation Choose Install Software at the beginning of the CD and follow the prompts to install SeaCOM . 3.2 System Installation The screen capture shown in Figure 3-1 is taken from a Windows ® 98 installation.
11 CHAPTER 3: Installation Figure 3-1. System Properties screen, Device Manager tab. You can access your new COM ports by using the assigned COM identifiers as shown in Figure 3-1. In this case, it is COM3, 4, 5, and 6. However, this assignment will vary from system to system.
12 DUAL- AND QUAD-POR T USB HUBS 4. Configuration 4.1 Original Configuration This device ships with the following configuration: • 422 mode, • 120 ohm termination, • 1 K-ohm pull-up resistance on RX+, and • 1 K-ohm pull-down resistance on RX-.
13 CHAPTER 4: Configuration T able 4-1. Jumper settings. Jumper Port RS-232 RS-422/485 E5 2 X E6 2 X E7 1 X E8 1 X Switch SW4 Settings To configure the ports on the Dual-Port USB Hub for RS-422/RS-485 instead of RS-232, select Jumper E7 for Port 1 and Jumper E6 for Port 2.
14 DUAL- AND QUAD-POR T USB HUBS T able 4-2. DIP-switch SW4 settings. Switch Switch Port Description RS-485 RS-422 Setting Number L SW4-1 1 TX+ to RX+ ON OFF L SW4-2 1 TX- to RX- ON OFF T SW4-3 1 Term.
15 CHAPTER 4: Configuration T able 4-3. DIP-switch SW3 settings. Switch Switch Port Description RS-485 RS-422 Setting Number 485 SW3-1 1 485 Mode (4-wire) ON OFF NE SW3-2 1 485 Mode, No Echo (2-wire) ON OFF 485 SW3-3 2 485 Mode (4-wire) ON OFF NE SW3-4 2 485 Mode, No Echo (2-wire) ON OFF NE = No Echo.
16 DUAL- AND QUAD-POR T USB HUBS T able 4-4. DIP-switches SW2 and SW4 settings. Switch Switch Port Description RS-485 RS-422 Setting Number L SW2-1 3 TX+ to RX+ ON OFF L SW2-2 3 TX- to RX- ON OFF T SW.
17 CHAPTER 4: Configuration Figure 4-4. RS-422/485 interface configuration. NOTE Switch positions SW3-1 and 2 are for Port 1, SW3-3 and 4 are for Port 2, SW1-1 and 2 are for Port 3, and SW1-3 and 4 are for Port 4. T able 4-5. DIP-switch SW1 and SW3 settings.
18 DUAL- AND QUAD-POR T USB HUBS each port. When selecting a configuration for your Hub, refer to Tables 4-6 through 4-8 and Figures 4-5 and 4-6. Jumpers E1, E2, E3, E4, E5, E6, E7, and E8 To configure Port 1 on the Quad-Port USB Hub for RS-232, select Jumper E8 on the circuit board.
19 CHAPTER 4: Configuration Figure 4-5. Switches SW2 and SW4. NOTE Switch positions SW4-1, 2, 3, 4, and 5 are for Port 1. Switch positions SW4-6, 7, 8, 9, and 10 are for Port 2. Switch positions SW2-1, 2, 3, 4, and 5 are for Port 3. Switch positions SW2-6, 7, 8, 9, and 10 are for Port 4.
20 DUAL- AND QUAD-POR T USB HUBS T able 4-7 (continued). DIP-switches SW2 and SW4 settings. Switch Switch Port Description RS-485 RS-422 Setting Number PD SW4-9 2 1K Pull-Down ON OFF PU SW4-10 2 1K Pull-Up ON OFF L = Loops TX+ to RX+ for two-wire operation.
21 CHAPTER 4: Configuration T able 4-8. DIP-switch SW1 and SW3 settings. Switch Switch Port Description RS-485 RS-422 Setting Number 485 SW1-1 3 485 Mode (4-wire) ON OFF NE SW1-2 3 485 Mode, No Echo (.
22 DUAL- AND QUAD-POR T USB HUBS Appendix A. T roubleshooting A.1 T roubleshooting T ips Serial Utility test software is supplied on the included CD-ROM and will be used in the troubleshooting procedures. By using this software and following these simple steps, you can eliminate most common problems without calling Technical Support.
23 A.2 Calling Black Box If you determine that your USB Hub is malfunctioning, do not attempt to alter or repair the unit. It contains no user-serviceable parts. Contact Black Box at 724-746-5500. Before you do, make a record of the history of the problem.
24 DUAL- AND QUAD-POR T USB HUBS Appendix B. Electrical Inter faces B.1 RS-232 Quite possibly the most widely used communication standard is RS-232. This implementation has been defined and revised several times and is often referred to as EIA/TIA-232.
25 B.3 RS-485 RS-485 is backward-compatible with RS-422; however, it is optimized for partyline or multidrop applications. The output of the RS-422/485 driver is capable of being Active (enabled) or Tristate (disabled). This capability allows multiple ports to be connected in a multidrop bus and selectively polled.
26 DUAL- AND QUAD-POR T USB HUBS Appendix C: Asynchronous Communication In serial data communication, individual bits of a character are transmitted consecutively to a receiver that assembles the bits back into a character.
27 Because each bit in asynchronous communication is sent consecutively, it is easy to generalize asynchronous communication by stating that each character is wrapped (framed) by pre-defined bits to mark the beginning and end of the serial transmission of the character.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 © Copyright 2002. Black Box Corporation. All rights reserved..
デバイスBlack Box RS422/485の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Black Box RS422/485をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack Box RS422/485の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black Box RS422/485の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black Box RS422/485で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black Box RS422/485を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack Box RS422/485の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black Box RS422/485に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack Box RS422/485デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。