ACTiメーカーE21Fの使用説明書/サービス説明書
ページ先へ移動 of 19
Box Camera Series Hardware Manual D2 1 (D21F / D21V) D22 (D22F / D22V ) E21 (E21F / E21V) E22 (E22F / E22V) E23 , E24, E25 201 3/ 12 / 04.
Hardware Manual 2 T able of Con tents Precautions ............................................................. 3 Safety Instructions .................................................................................... 5 Introduction .................
Hardware Manual 3 Precautions Read these instructio ns Y ou should read all the safety and operati ng instructions before usi ng this product. Heed all warnings Y ou must adhe re to a ll the warnings on the product and in the instruction m anual.
Hardware Manual 4 Federal Communic ations Commission Statem ent This equipment has been tested and found to comply with the limits for a class B digital device, p ursuant to Part 15 of the FC C Rules. These lim its are designe d to provide reasonabl e protection against harm ful interference in a reside ntial installation.
Hardware Manual 5 Safety Instructions Cleaning Disconnect this video prod uct from the power supp ly before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they ma y cause hazards.
Hardware Manual 6 Introduction The List of Models This hardware m anual contains the following m odels: D 21 F (D21) 1MP Box with D/N, Fixed lens D21V (D21) 1MP Box with D/N, V ari-focal lens D22F (D2.
Hardware Manual 7 E25 1.3MP Box with D/N, Basic W DR, SLLS, V ari-focal lens From the installation p erspective these models are very sim ilar; therefore y o u can use one manual for all of them .
Hardware Manual 8 Package Contents 1. Camer a 2. Lens OR Fixed focal lens with manual focus and f ixed iris V ari- focal lens with manual focus and DC iris 3.
Hardware Manual 9 Physical Descri ption 1) Ethernet Port The IP device connects to t he Ethernet via a sta ndard RJ45 connec tor . 2) Reset Button The purpose of reset button is to restore the factor y def ault settings of the cam era, including administrator ’ s pass word.
Hardware Manual 10 Installation and Access Camera Installa tion The box cam era may be installed indoors or o utdoors (requires waterpro of housing). In both cases, the m ounting block (included in the pack age) is needed. Indoor Installation For ceiling inst allations, the m ounting block has t o be m ounted to the top side of the c amera.
Hardware Manual 11 For pole or corner inst allations, you m ay consider following solutions : The housing can be either PMAX -0200, 0201 or PMA X- 0202.
Hardware Manual 12 Accessing Camera Connect th e Equipment T o be able to connect to the camera f irmware from your PC, both the cam era and the PC have to be connected to each other via Ethernet cable. At the sam e time, the camera has to have its own power supply .
Hardware Manual 13 In the exam ple below , we s uccessfully the cam era m odel that we had just co nnected to the network. By c licking with the m ouse c lick on th e cam era model, it is possible to automatically launch the default browser of the PC with th e IP address of the targ et cam era filled in the address bar of the browser alread y .
Hardware Manual 14 W ith just one click , you can launch the IP Utility and there will be an instant report as follows: Y ou c an quick ly notice the cam era m odel in th e list.
Hardware Manual 15 Manually adjust the I P address of the PC : In the following exam ple, based on W indows 7, we will configure the I P address to 192.
Hardware Manual 16 Manually adjust the I P addresses of multipl e cameras : If there are more than 1 cam era to be used in the same local area network and there is no DHCP server to assign u nique IP addresses to each of them , all of th e cam eras would then have the initial IP address of 192.
Hardware Manual 17 A ccess the Camera Now that the cam era and the PC are both hav ing their unique I P a ddresses and are under the same network s egment, it is possible to use the W eb browser of the PC to access the cam era.
Hardware Manual 18 The following examples i n this manual are bas ed on Internet E xplorer brow ser in orde r to cover all functions of the camera. Assum ing that the cam era ’ s IP address is 192.168 .0.100 , you can access it by opening the Web browser and t yping the following address into Web browser ’ s address bar: http://192.
Hardware Manual 19 T o check the firm ware version through the W eb Configurator , access the Setup page a nd click System > S ystem Info . For further operations , please refer to the F irmware User M anual .
デバイスACTi E21Fの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ACTi E21Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはACTi E21Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ACTi E21Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ACTi E21Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ACTi E21Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はACTi E21Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ACTi E21Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちACTi E21Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。