ACTiメーカーI92の使用説明書/サービス説明書
ページ先へ移動 of 45
Indoor PTZ Camera Hardware Manual I91, I92, KCM-81 1 1 V er . 2014/ 01 /1 4.
w w w .a c ti . c o m Hardware Manual 2 T able of Conte nts Precautions 4 Safety Instructions ........................................................................... 6 Introduction 8 List of Models .................................................
w w w .a c ti . c o m Hardware Manual 3 Resetting I92 / I93 Camera .......................................................... 39 A ccessing Camera 40 Configure the IP Addresses ........................................................... 40 A ccess the Camera .
w w w .a c ti . c o m Hardware Manual 4 Precautions Read these instructio ns Y ou should r ead all the safet y and operating instructi ons before usi ng this produc t. Heed all warnings Y ou m ust adhere to all the war nings on the product an d in the instruction m anual.
w w w .a c ti . c o m Hardware Manual 5 Federal Communic ations Commission Statement This equipment has be en tested and found to com ply with the limits for a class B digital device, p ursuant to Part 15 of the FCC Ru les. T hese limits are designed to provide reasonable prot ection against har mf ul interference in a residential installation.
w w w .a c ti . c o m Hardware Manual 6 Safety Instructions Don’t use the pow er suppl y with other voltages This device is lik ely to be dam aged or damage other equipm ents / personne l, if you use a power suppl y with different voltage than the one inc luded with this device.
w w w .a c ti . c o m Hardware Manual 7 4) If the video product does not operate normally by following the operating Instructions i n this manual. Adjust only those controls t hat are covere d by the .
w w w .a c ti . c o m Hardware Manual 8 In troduction List of Models This hardware m anual contains the following m odels: KCM-8111 2MP Indoor PT Z with D/N, Advance d W DR, SLLS, 18x Zoom lens I91 1M.
w w w .a c ti . c o m Hardware Manual 9 Package Contents Camera Power Adapter Universal Plug Con verter Surface Mount Mounting Scre w Kit Fixing Bracket Drill Template Term inal Block (for Power) Term.
w w w .a c ti . c o m Hardware Manual 10 Physical Description Connectors View 1) Memory Card Slot Insert a m emory card (not i ncluded) into the s lot for loc al recording purp oses.
w w w .a c ti . c o m Hardware Manual 11 Internal Vie w 1) Power Button (in KCM -81 1 1 on ly) The Power Button is used in case there is a need rest art the camera. T o restart the cam era, press the Power Button using a pointed object, suc h as a pen .
w w w .a c ti . c o m Hardware Manual 12 Before Installa tion Unpack ing the Camera NOTE: T o avoid scratches or leaving fingerprints on th e dome cover , it is recommended to retain t he p lastic covering th e dome cover until the cam era is c ompletel y installed.
w w w .a c ti . c o m Hardware Manual 13 3. Rotate the dom e cover clock wise to attach it. Preparing the Power A dapter In c ase of using a non-P oE switch or y our PoE switch has limited power s upply , y ou can use the bundled power a dapter and directly connect the cam era to a power outlet.
w w w .a c ti . c o m Hardware Manual 14 2. T ake note that the power adapter cable has t wo (2) different wires: 3. Connect the wire with the white stripe to the 1 2V pin an d the other to the GND p in. 4. Ti ghten the scre ws of the 1 2V pin and the G ND pins to secure the wire co nnection.
w w w .a c ti . c o m Hardware Manual 15 Preparing the DI/DO Connector Depending on your surveillance needs, you m ay conn ect digital input or output devices to your camera to trigger events or notifications. Digital Input (DI) devices ca n be used to notify the camera abo ut an activit y in the camera site.
w w w .a c ti . c o m Hardware Manual 16 T o connect output devices (DO), m ap the pins to one o f the pin com binations below: Device Pin Mapping Instructions Digital Output 1 (D O 1) 2 12V Connect the wires of the firs t output device to 12 V (Pin 2) and DO1 ( Pin 4).
w w w .a c ti . c o m Hardware Manual 17 High Voltage DO Device Connection Even though the cam era provides 12V po wer, this m ay not be enough for s ome high voltage DO devices, such as a ceiling light or a motor that opens or closes a gat e. In this case, the re is a need to connect an ex ternal rela y.
w w w .a c ti . c o m Hardware Manual 18 Installation Procedures There are several m ounting opt ions that you can use to install the cam era. Select t he most suitable solution for your installation environm ent. Mounting Solutions Mount T ypes Accessories Surface Mount Suitable when m ounting the cam era on hard or dropp ed ceilings.
w w w .a c ti . c o m Hardware Manual 19 Straight Wall Mount PMAX-01 10 PMAX-0305 (He avy Duty Wall Mount) V ertical Po le Mount Suitable when m ounting the cam era on vert ical poles. PMAX-01 10 PMAX-0305 PMAX- 0503 Horizontal Pole Mount Suitable when m ounting the c amera on horizo ntal poles .
w w w .a c ti . c o m Hardware Manual 20 Other Mounting A cces sories Accessories PMAX-0700 (Junctio n Box) PMAX- 0104 ( Extension Tub es) NOTE: For more inf ormation about the m ounting solutions and accessories, please ch eck the Mounting Accessory Se lector in our website ( http://www .
w w w .a c ti . c o m Hardware Manual 21 Mounting on the Ceiling There are three m ounting solutions that you can do to mount the cam era on the ceiling: Surface Mo unt : T o install the cam era directl y on the ceiling. Accessories com e bundled with the cam era pack age.
w w w .a c ti . c o m Hardware Manual 22 4. Align and attach th e fixing brac ket to one of the h oles on the cam era using the supplied screw (holes m arked belo w). The fixing bracket will fix the cam era position when mounted later . 5. Align and insert the c amera base h ooks to the m ounting holes of the m etal plate.
w w w .a c ti . c o m Hardware Manual 23 7. Ti ghten t he screw on the f ixing brack et to fix the camera position. This is to a void accidental camera movem ent as the cam era performs PT Z functions. 8. Connect the network cable , power adapter a nd an y other cable connectio ns (such as DI/DO, audio in, etc .
w w w .a c ti . c o m Hardware Manual 24 Using the Flush Mount Use the Flush Mount when installing the cam era on a dropped ceiling; there is space above the ceiling where the cam era body can be hidden from view and only the dome cover can be seen underneath the ceiling.
w w w .a c ti . c o m Hardware Manual 25 Step 2: Prepare t he Flush M ount 1. Push to detach the co ver ring from the m ount as marked belo w . Then set the cover ring aside. 2. Pee l off the lining of the three (3) f oam rubber pads and attach a ru bber pad to ea ch retaining brack et.
w w w .a c ti . c o m Hardware Manual 26 Step 4: Install the M ount 1. Insert the m etal bracket through the hole until the r ing edge is flat on the ce iling. 2. Position the retaining brac kets to hold th e mount on th e ceiling. NOTE: The following illustration shows how the flush mount will look l ike w hen viewed from inside the ceiling.
w w w .a c ti . c o m Hardware Manual 27 3. Ti ghten the scre ws to secure the m ount and m ake s ure the network cable, power a dapter , and other cables (if necessar y) are routed on the outer gap of the m etal brack et. 4. Attach the fixing bracket to one of the holes on the camera using the supplied screw (holes mark ed below).
w w w .a c ti . c o m Hardware Manual 28 Step 5: Connect the Cabl es and O ptional Accessories Insert a mem ory card into the cam era c ard slot (if necess ary) . Connect the network cable , pow er adapter , and other cables, such as DI/DO, etc.
w w w .a c ti . c o m Hardware Manual 29 2. Slide the camera clockwise to secure the hook s to the m ount. Notice that the fixing bracket screw becom es aligned with the ho le on the m etal bracket 3. Ti ghten t he screw on the f ixing brack et to fix the camera position.
w w w .a c ti . c o m Hardware Manual 30 Using the Pendant Mount In case of high ceilings, the camera can be lowered by pendant mount . NOTE: The Pendant Mount is not included in the cam era pack age.
w w w .a c ti . c o m Hardware Manual 31 3. Install the straight tub e on the ceiling. NOTE: If the straight tube is not long e nough, you may use one or mo re e xtension tubes (purchased separately).
w w w .a c ti . c o m Hardware Manual 32 3. T wi st the m ount kit to align the screw holes and attach the t wo (2) mounting sc rews (included in the m ount kit p ackage). Step 3: Install the Came ra 1. Connect the network cable to the Ethern et port of the c am era.
w w w .a c ti . c o m Hardware Manual 33 3. Slide the camera c ounter-c lockwise to secure the ho oks to the m ount. 4. On the top of the m ount kit, attach t hree (3) sc rews (included in th e m ount kit pack age) to secure the cam era to the mount.
w w w .a c ti . c o m Hardware Manual 34 Mounting on Straight W all There are four (4) mount ing solutions that you can do to mount the camera on the straight wall . The L-T ype W all Mo unt is used to i nstall the cam era facing down as if it is installed on a ceili ng (s ee below for m ounting instructions) .
w w w .a c ti . c o m Hardware Manual 35 using pliers. Then route the c able through the cabl e holes (A to B) as marked belo w . W ith the cable(s) dangling , attach three (3) sc rews (included in the camera pack age) to install the L-t ype wall mount onto th e wall.
w w w .a c ti . c o m Hardware Manual 36 2. Align and insert the c amera base h ooks to the m ounting holes. 3. Slide the camera c lockwise to secure t he hooks to the mount. 4. Attach three (3) sc rews (included in the L-t ype wall m ount package) to secure th e camera to the mount.
w w w .a c ti . c o m Hardware Manual 37 Other Straight W all Mounting Solutions Another straight wall mounting solution include the Heavy Dut y Mount Kit: PMAX - 0110 PMAX - 0305 (Heavy Duty Wall Mount) Cable can either go through a hole in the wall or pass through the cable hole underneath the mount.
w w w .a c ti . c o m Hardware Manual 38 Other Accessories and Adjustments How to Replace the Dome Cover Depending on your sur veillance needs, you m ay want to replace the bu ndled dom e cover with a smoke dom e cover availabl e for purchase. T o replace the dom e cover , do the following: 1.
w w w .a c ti . c o m Hardware Manual 39 How to Reset the Camera A reset m a y be necess ary if the following instances ha ppen: The adm inistrator ’ s password has be en forgotten and theref ore the cam era cannot be accessed.
w w w .a c ti . c o m Hardware Manual 40 Accessing Camera Configure the IP A dd resses In order to be able to communicate w ith the camera from y our PC, both the camera an d the PC have to be within th e sam e network s egment.
w w w .a c ti . c o m Hardware Manual 41 W hen the left m ouse is click ed on the cam era model name , the defau lt browser of the PC is automatically launch ed and the IP address of the target cam era is a lready fill ed in the address bar of the bro wser .
w w w .a c ti . c o m Hardware Manual 42 Use the default I P addres s of the camera If there is no DHCP server i n the given net work, the user m a y have to m anually assign the I P addresses to both the PC and th e cam era to make s ure they are in the sam e network segment.
w w w .a c ti . c o m Hardware Manual 43 Manually adjust the I P addresses of multiple cam eras If there are more than o ne camera to b e use d in th e s ame local are a net work and there is no DHCP server to ass ign unique IP addresses to each of them , all of the cam eras would then have th e initial IP addres s of 192.
w w w .a c ti . c o m Hardware Manual 44 A ccess the C amera Now that the camera and the PC both have their unique IP addresses and are under the same network segm ent, you can use Microsof t Internet Explorer on the PC to acc ess the cam era.
w w w .a c ti . c o m Hardware Manual 45 Assum ing that the cam era ’ s IP addres s is 192.168.0. 100 , you c an access it by opening the Web browser and typing the f ollowing address in to Web browser ’ s address bar: http://192.
デバイスACTi I92の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ACTi I92をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはACTi I92の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ACTi I92の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ACTi I92で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ACTi I92を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はACTi I92の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ACTi I92に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちACTi I92デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。