Bosch AppliancesメーカーSHU53の使用説明書/サービス説明書
ページ先へ移動 of 19
.
ENGLISH - 1 ENGLISH www.boschappliances.com INTRODUCTION .................................................. . 2 T OOLS AND MA TERIALS NEEDED ......................... . 3 MA TERIALS SUPPLIED .......................................... . 4 CHOOSING LOCA TION .
2 - ENGLISH www.boschappliances.com INTRODUCTION In addition to these instructions the dishwasher shall be installed: • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, in accordance with the Canadian Electric Code C22.
ENGLISH - 3 ENGLISH www.boschappliances.com TOOLS & MATERIALS NEEDED Tools Needed for Installation Additional materials may be required to comply with local codes. Figure 2 Materials Needed Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line.
4 - ENGLISH www.boschappliances.com MATERIALS SUPPLIED DISHWASHER INSTALLATION KIT (Clear Bag) D. T oe Panel Screws (8mm) (2) E. Mounting Brackets (1L & 1R) F.
ENGLISH - 5 ENGLISH www.boschappliances.com Select a location as close to the sink as possible for ready access to water and drain lines. Most of the installation work is done before the dishwasher is moved into place. Any built-in dishwasher must be fully enclosed on the top, both sides and back.
6 - ENGLISH www.boschappliances.com PLUMBING PREPARATION 1 . In order to reduce running time, Bosch recommends 140° F water inlet temperature. Your dishwasher will perform equally as well at 120° F water temperature, but the run time will be extended.
ENGLISH - 7 ENGLISH www.boschappliances.com ELECTRICAL PREPARATION • Cut a 1” (25.4mm) diameter hole in the cabinet (in area of Figure 9 B). For wood cabinets, sand the hole until smooth. For metal cabinets, cover the edge with a grommet. • Run flexible cable (as codes permit) from junction through hole in cabinet.
8 - ENGLISH www.boschappliances.com PLACING THE DISHWASHER Placing the Dishwasher The profile strips on the sides of the dishwasher allow the dishwasher to fit into a cabinet opening with a width of 23-5/8” (600 mm) to 24-1/8” (613 mm).
ENGLISH - 9 ENGLISH www.boschappliances.com DRAIN HOSE CONNECTION Drain Hose • Before beginning, turn off the water supply! • The access hole for the drain hose should be 1.25” (32 mm) diameter . • Use the hose clamps and rubber connection hose (Figure 3) to connect the drain hose to the sink, disposer or air gap (Figure 14).
10 - ENGLISH www.boschappliances.com HOT WATER CONNECTION Openings for water lines must be installed in the marked areas as shown in Figures 8 and 9 to avoid interference with the dishwasher frame or other components.
ENGLISH - 11 ENGLISH www.boschappliances.com ELECTRICAL SUPPLY CONNECTION • Install strain relief or conduit connector into opening on power supply box. • Strip the insulated wires, being extremely careful not to strip too much insulation. • Insert and securely fasten into strain re- lief , two-conductor supply cable with ground.
12 - ENGLISH www.boschappliances.com If you have an SHI model, an integrated model, you will have additional mounting hardware and a folded template sheet with installation instructions comprised of pictograms. In North America the stainless steel models of the integrated series (SHI series), have a control panel that is 5-5/16” (135 mm) tall.
ENGLISH - 13 ENGLISH www.boschappliances.com Figure 19 DOOR PANEL INSTALLATION *Note: Do not exceed 30 5/16” (770mm) for the overall front panel length. SEE FOLDED PANEL INSTALLATION TEMPLATE SHEET FOR STEP BY STEP INSTRUCTIONS ON HOW TO INSTALL YOUR DISHWASHER PANEL(S).
14 - ENGLISH www.boschappliances.com Figure 22 After installation of the dishwasher , open and close the door several times to make sure that it does so with ease. If the door closes too quickly or if the door falls open, the spring tension needs to be adjusted.
ENGLISH - 15 ENGLISH www.boschappliances.com SHY66 & SHX56 Series Base and Toe Panel Installation Steps BASE AND TOE PANEL Assembly Steps • Place J-Box Cover on J-Box, insert and tighten screw (Figure 26). • Drop screws inside holes in base part.
16 - ENGLISH www.boschappliances.com TOE PANEL AND HANDLE • Obtain T oe Panel Screws from the Dishwasher Installation Kit bag (see Figure 3). • Insert screws through the T oe Panel. • With a T orx screwdriver , fasten screws and toe panel into dishwasher base.
ENGLISH - 17 ENGLISH www.boschappliances.com LEAVE INSTALLATION INSTRUCTIONS AND USE & CARE MANUAL WITH OWNER. Final Checklist Check Electrical Requirements. Be sure you have correct electrical supply and recommended grounding method. T urn on the hot water shut-off valve and electrical supply .
18 - ENGLISH www.boschappliances.com.
デバイスBosch Appliances SHU53の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bosch Appliances SHU53をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBosch Appliances SHU53の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bosch Appliances SHU53の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bosch Appliances SHU53で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bosch Appliances SHU53を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBosch Appliances SHU53の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bosch Appliances SHU53に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBosch Appliances SHU53デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。