AdaptecメーカーFC4100の使用説明書/サービス説明書
ページ先へ移動 of 13
2U S TORAGE E NCLOSURE Q UICK I NSTALL G UIDE FS4100, FS45 00, SC4100, AND FC4100.
1 Kit Contents ■ Adaptec Storage Enclosure (FS4100, FS4500, SC410 0, or FC4100) ■ CD, including softwar e, drivers, and documentati on ■ Tw o p o w e r c a b l e s Note: Mounting rails for rack installations are sold separatel y . See your Adaptec reseller for pur chase information.
2 Safety Tips Caution: A fully l oaded enclosure is heavy . Reduce the weight of the enclosur e by removing the drive carriers before installing the enclosure in the rack or tower . (Y ou can also remove the two APCs to further r educe the weight, if requir ed.
3 Installing into an Equipment Rac k Begin the installation by removing the components from the packaging and placing them on an a ntistatic surface until you need them.
4 3 Secure the r ear rails you selected to the rear supports of the equipment rack, using the supplied screws, as shown in the Figure in Step 1 on page 3 . 4 Secure the fr ont rails to the rear rails, as shown below . 5 T ighten al l the screws befor e continuing.
5 7 Secure the fr ont of the enclosure with one scr ew on each side, as shown in the next Figur e. The equipment rack instal lation is complete. Continue w ith Step 2: Installing the Drive Carriers on page 6 . Installing into a T ower Assembly A tower assembly is also referred to as a deskside assembly or pedestal.
6 3 Remove the tower ’s front bezel, as shown below , saving the screws for use in Step 5 . 4 T urn the enclosure 90° so that the right hand rack mount ear and LEDs ar e on top, then slide the Storage Enclosure into the tower skin, as shown above. 5 Replace the front bezel, using the scr ews r emoved in Step 3 .
7 2 W ith the cam lever of the drive sl ot fully open, slide the carrier into the slot until the lever starts to close. 3 Push the cam lever until it engages the latch on the left side of the carrier asse mbly and clicks into place. 4 Repeat for all drive carriers.
8 Connecting SA T A Cables The FS4100 and FS4500 St orage Enclosures have removable Small Form-factor Pluggable (SFP ) connectors that support copper or optical cables.
9 Connecting FC Cables The FC4100 Storage Enclosure has r emovable Small Form-factor Pluggable (SFP) connectors that support copper or optical cables. Ensur e that you have the appropriate SFP instal led for your cables.
10 Connecting Ultra320 SCSI Cables See the Adaptec 2U Storage Enclosur e In stallation and User ’ s Guide on the CD for supported cable lengths and additional cabling information. Caution: Use only Ultra320 certified cables. Ultra160 certified cables are not supported by the Adaptec SC4100 Storage Enclosure.
11 Step 5: Connecting P o wer Cords to the APC Modules. Connect one of the supplied power cor ds to each of the APC modules and to a grounded power outlet. Caution: Always use a regulating uninterrupti ble power supply (UPS) to protect your Storage Enclosure.
R Adaptec, Inc. 691 South Milpitas Boulevard Milpitas, CA 95035 USA ©2004 Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. which may be registered in some jurisdictio ns. Part Number: MAN-40 0 0-QUIK, Re v .
デバイスAdaptec FC4100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Adaptec FC4100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAdaptec FC4100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Adaptec FC4100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Adaptec FC4100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Adaptec FC4100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAdaptec FC4100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Adaptec FC4100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAdaptec FC4100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。