Boss Audio SystemsメーカーFDR-1の使用説明書/サービス説明書
ページ先へ移動 of 24
FET Owner’ s Manual DC AC AC & BATTERY POWERED FDR-1_e1.book 1 ページ ２００７年１月５日 金曜日 午後６時７分.
2 Thank you, and congratulations on your choice of the BOSS FDR-1 Deluxe Reverb. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). These sections provide important in- formation concerning the proper operation of the unit.
3 Main Features ● Uses COSM technology to model the amp sound of a Fender ® DELUXE REVERB ® . ● Makes it easy for you to enjoy that vintage Fender ® amp sound simply by connecting the FDR-1 to your usual guitar amp. ● Features reverb and vibrato effects like those on an actual DELUXE REVERB ® amp.
4 Panel Descriptions fig.FDR-1_name1.eps 1. AC Adaptor Jack This jack accepts the connection of an AC adaptor (optionally available BOSS PSA-se- ries). By using an AC adaptor, you can play without being concerned about how much battery power you have left.
5 Panel Descriptions 2. CHECK Indicator This indicator shows whether the effect is on or off, and also doubles as the battery check indicator. The indicator lights when the ef- fect is on.
6 Panel Descriptions fig.FDR-1_name1.eps 7. GAIN Knob This adjusts the amount of distortion and the volume level. Turning it clockwise makes distortion stronger and increases the volume level. 8. LEVEL Knob This adjusts the volume of the effect sound.
7 Connections * Inserting a connecting plug into the INPUT jack turns on the power to the unit. * Raise the amp volume only after turning on the power to all connected devices. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high.
8 Connections Recommended Settings fig.FDR-1-connenct-e.eps * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power-up is required before the unit will operate normally. AC Adaptor BOSS PSA-series (option) 9V DC/200 mA Guitar Amplifier (JC-120 etc.
9 Connections Recommended Settings for a Roland JC-120 fig.FDR-1_JC-120.eps Recommended Settings for a Fender ® Combo Amp fig.FDR-1_TWINREVERB.eps Recommended Settings for a Stack Amp fig.FDR-1_JCM2000.eps We recommend using a clean setting (no dis- tortion) on the connected amp.
10 Operating the Unit fig.FDR-1_operation1.eps 1. After you have made the necessary connections (p. 7, p. 8 ) , set the panel knobs as shown in the illustration. 2. Depress the pedal switch to turn the effect on. (The CHECK indicator lights when the effect is on.
11 Operating the Unit fig.FDR-1_operation4.eps 5. Adjust the output vol- ume with the LEVEL knob. Normally, you should adjust the LEVEL knob so there’s no difference in the volume when switching the effect on and off. fig.FDR-1_operation5.eps 6. Adjusts the amount of vibrato effect (cyclical fluctuations in volume) with the VIBRATO knob.
12 Operating the Unit Setting the Vibrato Rate Using the Pedal Switch (RATE Setting Mode) When Setting the Vibrato by Inputting the Tempo with the Effect On (CHECK indicator: Red) fig.FDR-1_vibrato1.eps * Vibrato rate for use with the tempo settings can be made in the range of 0.
13 Operating the Unit When Setting the Vibrato by Inputting the Tempo with the Effect Off (CHECK indicator: Off) fig.FDR-1_vibrato2.eps * Vibrato rate for use with the tempo settings can be made in the range of 0.
14 Changing the Battery When the indicator goes dim or no longer lights while the effect is on, it means that the battery must be replaced. Replace the battery following the steps below. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high.
15 Troubleshooting The power won’t come on/ the CHECK indicator doesn’t light ● Is the specified adaptor (PSA-series, sold separately) properly connected? Check the AC adaptor connection (p. 7, p. 8). * Never use any AC adapter other than one specified for use with the FDR-1.
16 Setting Samples Standard Crunch Sound fig.FDR-1-sample1.eps Hard Overdrive Sound fig.FDR-1-sample1.eps Surf Rock Sound fig.FDR-1-sample1.eps Vibrato Sound fig.FDR-1-sample1.eps For details about the vibrato rate, please refer to p. 12, p. 13. FDR-1_e1.
17 Setting Memo fig.FDR-1-memo.eps fig.FDR-1-memo.eps fig.FDR-1-memo.eps fig.FDR-1-memo.eps FDR-1_e1.book 17 ページ ２００７年１月５日 金曜日 午後６時７分.
18 Setting Memo fig.FDR-1-memo.eps fig.FDR-1-memo.eps fig.FDR-1-memo.eps fig.FDR-1-memo.eps FDR-1_e1.book 18 ページ ２００７年１月５日 金曜日 午後６時７分.
19 Specifications FDR-1: Deluxe Reverb Nominal Input Level: ....................... -20 dBu Input Impedance:.............................. 1 M Ω Nominal Output Level: .................... -20 dBu Output Impedance: .......................... 2.2 k Ω Recommended Load Impedance:.
20 Specifications Weight: ............................................... 440 g /1 lb (including battery) Accessories..................................
21 MEMO FDR-1_e1.book 21 ページ ２００７年１月５日 金曜日 午後６時７分.
22 MEMO FDR-1_e1.book 22 ページ ２００７年１月５日 金曜日 午後６時７分.
This product complies with the requirements of European Directive 89/336/EEC. For EU Countries For Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
G6027116R0 FDR-1_e1.book 24 ページ ２００７年１月５日 金曜日 午後６時７分.
デバイスBoss Audio Systems FDR-1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Boss Audio Systems FDR-1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBoss Audio Systems FDR-1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Boss Audio Systems FDR-1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Boss Audio Systems FDR-1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Boss Audio Systems FDR-1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBoss Audio Systems FDR-1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Boss Audio Systems FDR-1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBoss Audio Systems FDR-1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
