Boston AcousticsメーカーGT-50の使用説明書/サービス説明書
ページ先へ移動 of 19
GT-50 5-Channel, High-Curr ent/High-Power Amplifier.
2 T able of Contents Parts List 3 Features and Specifications 3 Control Functions 4 Control functions (cont.) 5 Control functions (cont.) 6 Mechanical Functions 6 Control cover r emoval and reinstallation 6 Multi-position mounting feet 6 Mechanical functions (cont.
Included Hardwar e (1) owner’ s manual (1) female quick-connect terminal for remote input (1) 2mm hex wrench (for speaker input) (1) 3mm hex wrench (for power input) (6) mounting screws 3 Parts List GT -50 Specifications 14.4VDC Power Multi-Channel Power @ 4 Ω 4x55W , 1x250W Multi-Channel Power @ 2 Ω 4x85W , 1x350W Mixed Op.
4 Contr ol Functions FRONT RCA Inputs RCA cables marked “FRONT” from head unit or fr om other line level device should be connected here. Use both inputs (L & R) for ster eo. FRONT , REAR, and SUBWOOFER Remote Inputs Use the supplied FEMALE quick connector to connect the REMOTE trigger lead from the head unit to the amplifier .
FRONT and REAR “Q” Controls “Q” Control is active when the highpass cr ossover is engaged and is centered on the selected crossover point. The range of operation is 0.7–1.2. REAR RCA Inputs RCA cables marked “REAR” from head unit or other line level device should be connected here.
6 Mechanical Functions Recessed RCA Inputs The input jacks are r ecessed into the body of the amplifier to provide clear- ance in tight mounting locations. Control Cover Removal and Reinstallation The cover panel is secured with two (2) captive coin-slotted scr ews.
Mechanical Functions (cont.) V ents (Side and Rear) The cooling vents must be kept clear of obstructions once the amplifier is installed. Failure to do this could lead to prematur e thermal shutdown or amplifier failure. Amplifier Linking The design of the side panels enables multiple amplifiers to be used together without additional hardwar e.
8 Before Y ou Install Before you install the unit, disconnect the negative (–) battery cable in the engine compartment of the vehi- cle. Doing so will prevent damage to both the electrical system of the vehicle and the amplifier during installation.
13mm ( 1 / 2 ”) 225mm (8 7 / 8 ”) SUBWOOFER OUTPUT HIGHPASS OFF ON 5 0.2 V INPUT SENSITIVITY 2.6 20 350 Hz 200 REMOTE POWER B+ B+ POWER GND GND FUSE 3 x 30A FRONT SPEAKER OUTPUT L R REAR SPEAKER OUTPUT L R 12dB 24dB OFF LOWPASS 50 350 Hz 200 NON PRINTABLE AREA REAR INPUT STEREO MONO L+R HIGHPASS OFF ON 5 0.
10 Passenger and T runk Compartment Mounting If the amplifier is mounted under a seat, be sure that the vents do not become blocked. Do not allow seat padding or other obstructive material to press down on the amplifier . All Boston GT amplifiers have top panel controls.
FRONT SPEAKER OUTPUT L R REAR SPEAKER OUTPUT L R Power/B+ and Power/GND Connection Strip approximately 5 / 8 " (16mm) of insulation. The positive (+) power wir e is installed into the amplifier terminal marked “B+.” The negative (–) wire is installed into the terminal marked “GND.
12 Mono Subwoofer Operation Connect either a 2-ohm or 4-ohm subwoofer to a single (+) and (-) terminal (see System A, page 16). When using two (2) subwoofers, each subwoofer should be a minimum 4-ohm [or higher] impedance, (see System B, page 17). W ARNING! Subwoofer impedance must not fall below 2 ohms when in MONO mode.
13 Setup T uning—Full-Range Speakers (cont.) 4) Head Unit The head unit should have all controls such as bass, tr eble, balance, and fader set to the flat or centered position.
14 8) FRONT and REAR “Q” Controls Once the FRONT highpass crossover point has been determined, use the FRONT “Q” control to incr ease the bass information centered ar ound the crossover point.
15 5) SUBWOOFER Sensitivity Control Tu rn controls all the way counter clockwise (minimum position). In this position, the amplifier will be less sen- sitive to the input signal from the head unit. Slowly r otate this control clockwise until maximum undistorted playing level is heard fr om the subwoofers.
16 System Examples SYSTEM A—Front, Rear , and Single 2 Ω Subwoofer (2 Ω load) L R L R ON ON SAFE SAF E 6 . 5 L F 6 . 5 L F fuse to + battery terminal to gr ound fuse to + battery terminal to ground 12.
17 SYSTEM B—Front, Rear , and Dual 4 Ω Subwoofers (2 Ω load) with Discrete Subwoofer Input L R L R ON ON SAFE SAF E 6 . 5 L F 6 . 5 L F fuse to + battery terminal to gr ound fuse to + battery terminal to ground 6 .
18 Amplifier T r oubleshooting Guide Status LEDs on Amplifier not Lit — Head Unit (Sour ce) T urned “ON” V erify Remote turn-on wire fr om source to amplifier has pr oper voltage Power (B+) c.
19 Contact and W arranty Information 300 J ubilee Drive Pe a b o d y, MA 0 1 960 U.S.A. (978) 538-5000 Boston, Boston Acoustics, and the Boston logo are r egister ed trademarks of Boston Acoustics, Inc. © 2003 Boston Acoustics, Inc. All rights reserved.
デバイスBoston Acoustics GT-50の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Boston Acoustics GT-50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBoston Acoustics GT-50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Boston Acoustics GT-50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Boston Acoustics GT-50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Boston Acoustics GT-50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBoston Acoustics GT-50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Boston Acoustics GT-50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBoston Acoustics GT-50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
