Boston AcousticsメーカーSPZ60の使用説明書/サービス説明書
ページ先へ移動 of 26
.
Index Introduction Page 2 Specifications Page 3 Dimensions Page 4 Included Parts and Accessories Page 6 T weeter Installation Page 8 Axis Mount / Phase Plug Installation Page 10 SPZ50 W oofer Installa.
Introduction Thank you for purchasing the Boston Acoustics SPZ component system. Nothing better describes SPZ components than best-in-class. With nearly 1-inch of peak-to-peak excursion, SPZ delivers more bass from a standard size speaker opening.
3 Specifications Model: SPZ60 SPZ50 Nominal Size: 6 1 ⁄ 2 " (165mm) 5 1 ⁄ 4 " (135mm) RMS Power Handling: 150w 150w Max Power Handling: 300w 300w Nominal System Impedance: 3 Ω 3 Ω W .
SPZ50 Woofer 92.1mm 3.62” 61.9mm 2.54” 36mm 1.42” 119mm 4.69” 36mm 1.42” 67.4mm 2.65” 97.6mm 3.84” 134mm 5.27” SPZ60 Woofer 4 Dimensions.
Dimensions 5 110mm 4.33” 197mm 7.75” 56.1mm 2.21” SPZ Crossover SPZ T weeter 1 8mm .71” 27mm 1.1” 43mm 1.69” 52mm 2.05” 38mm 1.5” 51mm 2”.
SPZ60 Included Parts and Accessories: 6 # Description Quantity 1 SPZ60 Woofer 2 2 T ype-M1 1" Alloy Dome T weeter 2 3 SPZ60 Crossover 2 4 T weeter Grille 2 5 T weeter Axis-Mount 2 6 T weeter Flus.
SPZ50 Included Parts and Accessories: 7 # Description Quantity 1 SPZ50 Woofer 2 2 T ype-M1 1" Alloy Dome T weeter 2 3 SPZ50 Crossover 2 4 T weeter Grille 2 5 T weeter Axis-Mount 2 6 T weeter Flus.
8 T weeter Installation: Flush Mount 19 18 17 6 2 4 1) Drill a hole for the tweeter cup (1 3 ⁄ 4 ”/ 45mm) making sure that there is adequate depth available ( 3 ⁄ 4 ”/ 19mm). 2) Connect the speaker wires to the tweeter cup . 3) Insert the tweeter cup into the mounting hole.
T weeter Installation: Angle Mount 18 21 7 22 8 2 4 19 18 17 6 2 4 1) Drill a hole for the speaker wire and pre-drill for the mounting screws if necessary 2) Mount the bottom cup to the mounting surface using the provided screws routing the speaker wires through the center hole.
10 SPZ W oofer Axis Mount Installation: 10 4 2 27 5 1 1) Insert the axis mount into the woofer . 2) Insert and hand-tighten the retaining screw with the provided tool . 3) Insert the tweeter into the axis mount , twist clockwise to lock the tweeter into position.
SPZ W oofer Phase Plug Installation: 10 27 26 1 1) Insert the phase plug into the woofer . 2) Insert and hand-tighten the retaining screw using the provided tool .
SPZ50 W oofer Installation: 9 1 32 11 12 13 14 1) Install the gaskets on the mounting flange of the woofer and the back side of the 5 1 ⁄ 4 ” (135mm) adapter ring . 2) Mount the speaker into the speaker location using the provided screws . 3) Position the axis mount into the desired location (if applicable), refer to page 17.
13 SPZ60 W oofer Installation with Grille: 9 9 1 29 9 11 12 2 1 14 13 1) Install the gaskets on the mounting flange of the woofer and the back side of the 6” (160mm) adapter ring . 2) Mount the speaker into the speaker location using the provided screws .
9 9 1 1 29 9 31 3 9 30 9 11 12 23 2 16 15 14 13 14 SPZ60 W oofer Installation with 6 1 ⁄ 2 ” (165mm) V ariMount ™ Adapter Rings: 1) Install the gaskets on the mounting flange of the woofer and the back side of the 1 ⁄ 2 ” (13mm) spacer ring (if applicable).
SPZ60 W oofer Installation with 5 x 7” V ariMount ™ Adapter Rings: 15 9 9 1 1 1 29 9 31 31 9 30 9 28 11 12 23 23 16 15 15 16 20 1 1) Install the gaskets on the mounting flange of the woofer and the back side of the 1 ⁄ 2 ” (13mm) spacer ring (if applicable).
16 Connecting Speaker Wires: 10 10 1) Strip 1 ⁄ 4 ” (10mm) of shield off of the speaker wires. 2) Insert the wire into the speaker terminal observing proper polarity . 3) Hand-tighten the gold set screws using the provided tool (2.5mm). ( Note: do not overtighten the set screws.
17 SPZ Axis Mount Positioning: 10 The axis mount on the SPZ woofer is designed so it can be positioned to properly direct the tweeter’ s output towards the listening position. 1) Loosen the retaining screw located on the face of the axis mount with the provided tool (2.
10 25 24 Crossover Installation: 20 1) Remove the four screws and located at each corner of the top panel. 2) Once the screws are removed, the cover will lift off the chassis. 3) Using the provided screws , secure the crossover to a solid surface. Note; Due to shock and vibration, the crossovers should not be installed in the doors of the vehicle.
19 Crossover Configuration: Axis / Comp Mount Switch: The “Axis/Comp” switch optimizes the output from the crossover for the configuration of the component system. Use the “Axis” setting if the tweeter is installed in the axis mount, use the “Comp” setting if the tweeter is installed separate from the woofer .
SPZ System Wiring (Standard): Standard Wiring (Coaxial Configuration) Standard Wiring (Component Configuration) 20.
SPZ System Wiring (Bi-Amplification / Bi-Wiring): Bi-Amplification Bi-Wiring 21.
Contact Information Contacting Boston For questions regarding installation or service, please contact the dealer from whom you have purchased the product or contact us directly at: Boston Acoustics, Inc. 300 Jubilee Drive Peabody , MA 01960 Phone #: 978-538-5000 Fax #: 978-538-5100 Email: support@bostona.
23 Notes:.
24.
Boston Acoustics, Inc. 300 Jubilee Drive, Peabody , MA 01960 USA T : 978.538.5000 F: 978.538.5100 W: bostonacoustics.com 042-002423-0.
デバイスBoston Acoustics SPZ60の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Boston Acoustics SPZ60をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBoston Acoustics SPZ60の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Boston Acoustics SPZ60の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Boston Acoustics SPZ60で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Boston Acoustics SPZ60を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBoston Acoustics SPZ60の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Boston Acoustics SPZ60に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBoston Acoustics SPZ60デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。