Boston AcousticsメーカーVSi 580T2の使用説明書/サービス説明書
ページ先へ移動 of 21
V Si 580T2 HSi 470T2 Single Stereo Direct/Diffuse In-Ceiling Speaker Sy stem Altav oz estér eo único directo/ difuso para techo Enceinte de plaf ond simple stéréo directe/diffusion Stereo Einz ell.
operating mode diffuse direct Input "A" Input "B" – 2 – Quick Reference Configur ation Guide Guía de configuración de referencia r ápida Guide de référenc e de configura t.
C ontents Configuration Guide . . . . . . . . . . . .2 Introduction . . . . . . . . . . . . . . . . . . .3 Specifications . . . . . . . . . . . . . . . . . . .4 Parts List . . . . . . . . . . . . . . . . . . . . . . .5 Placement/Loca tion Tips . . . .
– 4 – Frequency Response (±3dB) Recommended Amp P ower Nominal Impedance S en s i ti v i t y (2.83v at 1m) T weeter Bass Unit Crossov er Frequency External Dimensions (Diameter) Mounting Hole Dia.
– 5 – Included • Speaker • Grille w/scrim cloth • Paint shield • Cutout template • Screwdriver bit Placement / L ocation Tips Since the speaker installation is per- manent and the furnit.
– 6 – Surround Speaker When using the T2 speakers as sur- round speakers, you will want to locate the speakers on opposite sides of the room, located parallel with or behind the listening area.
– 7 – Surround Placemen t Option #2 Surround Placement Option #1 8–12 feet (2.4–3.6m) Front 8—16 feet ( 2.4—4.8m) Front Surround Placement Option #1 • Direct mode • Tw eeters face fron.
– 8 – Surround Placemen t Option #4 Surround Placement Option #3 12–20 feet (3.6–6m) Front 8–12 feet ( 2.4–3.6m) Front Surround Placement Option #3 • Direct mode • Tw eeters face front.
– 9 – Surround Placemen t Option #6 Surround Placemen t Option #5 8–12 feet (2.4–3.6m) 4–10 feet (1.2–3m) Front 8–12 feet ( 2.4–3.6m) Front Surround Placement Option #5 • Side speake.
Fiber glass lining Additional drywall screws A dhesiv e bet w een studs and drywall – 10 – Joist Ceiling Material VSi 580T2 10 7 / 8 " 2 76mm 12 7 / 8 " 326mm HSi 470T2 8 7 / 8 " 22.
– 11 – Bass Management If you are using your T2 loudspeak er with a surround-sound processor and subwoofer , set the bass management control to “small” for the VSi 580T2 and the HSi 470T2. Consult your surround-sound receiv er or processor manual for instructions on changing bass management settings.
– 12 – W iring Depending on the application, there are several differ ent ways to wire the T2 speaker . Single Stereo Speak er If your T2 speaker is going to be used as the sole stereo speaker , refer to the diagram below . 1 . Set the input jumper (located on the back of the T2 speaker) to the Dual Input Setting (see 1).
– 13 – Surround Speaker If your T2 speaker is going to be used as a surround speaker , refer to the diagram below . 1. Set the input jumper (located on the back of the T2 speaker) to Single Input Setting (see 1). 2. Connect the speaker wire to Input “ A” only.
– 14 – Installation Instructions W ARNING Always turn off the amplifier or receiv- er when connecting speakers or any other components to the system.
– 15 – All Installations 1. Str ip 1 / 2 -inch (12mm) of insulation from the wire, and twist the wire strands together . The T2 speaker jack will accept either bare wire (up to 12-gauge) or single banana plugs. 2. Connect the wire to the speaker, being careful to retain pr oper polarity.
– 16 – 5. Rotate the t weeter island by touch- ing the outside edges only—do not directly touch the tweeters (see diagram #8). T o determine the best direction in which to position the tweeter plane, please read the Surround Speaker section found on pages 6 through 9.
– 17 – P ainting The Speaker F rame The speaker may be painted before or after installation. The speaker has already been primed. 1. I nsert the supplied paint shield into the frame of the speaker (see dia- gram #10). 2 . Paint the frame. If you are using spray paint, apply two light coats.
Po wer Handling/ Listening Lev els The power recommendations f or the speaker assume that you will oper- ate the amplifier in a way that will not produce distortion. Even our rugged speakers can be damaged by an amplifier if it is producing distortion.
– 19 – Notes: Notas: Remarques : Anmerkungen:.
B ost on, B ost on A c oustics , the B oston Acoustics logo, and Kortec are registered tr ademar ks of B ost on A c oustics , I nc. Specifica tions ar e subjec t t o change without notic e . © 2008 B ost on A c oustics , I nc . 142-003575-0 300 Jubilee Dr iv e , P eabody, MA 01960 USA bostonacoustics.
Documen t Notes: A pproved b y: Date: Artwork Description: 142-003575-0 V Si 580T2 HSi 470T2 OM Creat ed By: B r i a n S p i e l v o g e l , Senior M arketing Communication Manager , 9 7 8 .
デバイスBoston Acoustics VSi 580T2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Boston Acoustics VSi 580T2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBoston Acoustics VSi 580T2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Boston Acoustics VSi 580T2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Boston Acoustics VSi 580T2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Boston Acoustics VSi 580T2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBoston Acoustics VSi 580T2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Boston Acoustics VSi 580T2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBoston Acoustics VSi 580T2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。