Boston AcousticsメーカーVSi H470T2の使用説明書/サービス説明書
ページ先へ移動 of 20
HSi H460T2 W eather-Resistant S ter eo In- C eiling Speaker • W eather and high-humidity resistant materials • Ideal for bathr ooms , saunas, and por ches Haut-parleur stéréo encastr é au plafo.
– 2 –.
Con tents Configuration Guide . . . . . . . . . . . .2 Introduction . . . . . . . . . . . . . . . . . . .3 Specifications . . . . . . . . . . . . . . . . . . .4 Parts List . . . . . . . . . . . . . . . . . . . . . . .5 Placement/Loca tion Tips . . . .
– 4 – Fr equency Response (±3dB) Recommended Amp P ower Nominal Impedance S en si t iv i ty (2.83v at 1m) T weet er Bass Unit Crossov er Fr equency External Dimensions (Diameter) Mounting Hole Di.
– 5 – Included • Speaker • Grille w/scrim cloth • Paint shield • Cutout templat e • Screwdriver bit (VSi H470T2 only) Placement / L ocation Tips Exterior locations that include some protection from the elements are preferr ed. Unprotected outdoor locations may cause the speaker to deteriorate more quickly over time .
– 6 – Surround Speaker When using the speakers as sur- round speakers, you will w ant to locate the speakers on opposite sides of the room, located parallel with or behind the listening area. Once each of the speakers is installed, the speaker can be fine-tuned by rotating the tweeter island and switching between direct and diffuse modes.
– 7 – Surround Placement Option #2 Surround Placement Option #1 8–12 feet (2.4–3.6m) Front 8—16 feet (2.4—4.8m) Front Surround Placement Option #1 • Direct mode • T weeters face fr ont.
– 8 – Surround Placement Option #4 Surround Placement Option #3 12–20 feet (3.6–6m) Front 8–12 feet (2.4–3.6m) Front Surround Placement Option #3 • Direct mode • T weeters face fr ont .
– 9 – Surround Placement Option #6 Surround Placement Option #5 8–12 feet (2.4–3.6m) 4–10 feet (1.2–3m) Front 8–12 feet (2.4–3.6m) Front Surround Placement Option #5 • Side speakers.
Fiber glass lining Additional drywall screws Adhesive between studs and drywall – 10 – Joist Ceiling Material 8 ¾ " 222mm 6 ¾ " 171mm 10 ⁄ " 275mm 8 ⁄ " 225mm Installation T ips Required Clearanc es Behind the mounting surface, there must be 1-inch (25mm) of clearance around the mounting hole.
– 11 – Bass Management If you are using your High Humidity loudspeaker with a surround-sound processor and subwoof er , set the bass management control to “small” for the HSi H460T2 and the VSi H470T2. Consult your surround-sound receiver or pr ocessor manual for instructions on changing bass management settings.
– 12 – Wiring Depending on the application, there are sever al different wa ys to wire the speaker . Single Stereo Speaker If your speaker is going to be used as the sole stereo speaker , refer to the diagram below . 1. Set the input jumper (located on the back of the T2 speaker) t o the Dual Input Setting (see 1).
– 13 – Surround Speaker If your speaker is going to be used as a surround speaker , refer to the diagram below . 1. Set the input jumper (located on the back of the speaker) to Single Input Setting (see 1). 2. Connect the speaker wire to Input “ A” only .
– 14 – Installation Instruc tions W ARNING Always turn off the amplifier or receiv er when connecting speakers or any other components to the system.
– 15 – All Installations 1. Strip 1 ⁄ 2 -inch (12mm) of insulation from the wire, and twist the wire strands together . The speaker jack will accept either bare wire (up to 12-gauge) or single banana plugs. 2. Connect the wire to the speaker , being careful to retain pr oper polarity.
– 16 – 5. Rotate the tweeter island by touching the outside edges only— do not directly touch the tweeters (see diagram #8). T o determine the best direction in which to position the tweeter plane, please read the Surround Speaker section found on pages 6 through 9.
– 17 – P ainting The Speaker F rame The speaker may be painted bef ore or after installation. The speaker has already been primed. 1. I nsert the supplied paint shield into the frame of the speaker and secure with tape if necessary. (see diagram #10).
Po wer Handling/ Listening Lev els The power r ecommendations for the speaker assume that you will operate the amplifier in a way that will not produce distortion. Even our rugged speakers can be damaged by an amplifier if it is producing distortion. If you hear a harsh, gritty sound, turn down the volume.
– 19 – For EU C ustomers Only This symbol found on the product indicates that the product must not be disposed of with household waste. Instead, it ma y be placed in a separate collection facility for electronic waste or returned to a retailer when purchasing similar product.
© 2008 Boston Acoustics, Inc. Boston, Boston Ac oustics, the Boston Acoustics logo , Kortec and VR are register ed trademarks and the B/A ellipse symbol is a trademark of Boston Acoustics , Inc. Dolby Digital, and Dolby Pro L ogic are register ed trademarks of Dolby Laboratories .
デバイスBoston Acoustics VSi H470T2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Boston Acoustics VSi H470T2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBoston Acoustics VSi H470T2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Boston Acoustics VSi H470T2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Boston Acoustics VSi H470T2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Boston Acoustics VSi H470T2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBoston Acoustics VSi H470T2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Boston Acoustics VSi H470T2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBoston Acoustics VSi H470T2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。