BraunメーカーNUVL855RM24の使用説明書/サービス説明書
ページ先へ移動 of 38
Under -V ehicle Lift ® W A R N I N G Read manual before installing or servicing lift. Failure to do so may result in serious bodily injury and/or property damage.
The Braun Corporation NUVL855RM24 01-00025 07/09/2007 1-800-THE-LIFT BRAUNLIFT .COM TM MFG DA TE SERIAL NUMBER TM DOT Private Use Lift MODEL# Max. Lifting Capacity - 700Lbs. W e at The Braun Corporation wish to express our fullest appr eciation on your new pur chase.
Page 1 Contents T roubleshooting and Maintenance Lift T erminology ............................................................ 2 Switch and Sensor Locations ..................................... 3 Certi fi cation Checklist Diagnostic Procedures ....
Page 2 Outboard Right Left Inboard Lift T erminology Hydraulic Cylinders Rolling Horizontal Arms Outer Barrier Actuator Platform Cable-activated Manual Release System Hand-Held Attendant's Contro.
Page 3 Switch and Sensor Locations Barrier Down Limit Switch 73950RNA Lift Out Cam 73775 Pressure T ransducer 30426 Full Out Cam 75776CN Lift Out Limit Switch 73950A Full Out Limit Switch 73950A Switc.
Page 4 • V ehicle movement is prevented unless the lift door is closed, ensuring the lift is stowed. 1. V erify lift stowed signal (pin 7) in the 9 conductor plug on the side of the pump module has a +24 volt signal. 2. Refer to the interlock installation instructions.
Page 5 Adjustments and Calibration Adjustment Procedures Lift Out Switch: The Lift Out Switch stops inward travel of the carriage/platform during Stow function (activated by the housing-mounted Lift Out Cam). Move cam in to increase inward travel. Move cam out to decrease inward travel.
Page 6 K MP916 0.010 Ω .5% R 103 103 321 321 321 V104 LCD MODULE 8.00M L_DN B_UP L_OUT L_UP B_DN L_IN 50# CAL O_BAR D14 J27 U? CYCLE DIAG U15 U11 U10 U2 J9 J11 J10 J17 J16 J14 J8 J5 J21 J19 J20 D9 D6.
Page 7 Floor Level and Inner Roll Stop Adjustments Achieving proper fl oor level positioning of the plat- form and inner roll stop requires a combination of Floor Level switch adjustment and inner roll stop adjustment. Both are factory set but must be in- spected during installation procedures (will vary per vehicle application).
Page 8 O P E N C L O S E VA LV E 2. Position the lift platform ap- proximately 12" above stow level using the manual operation system . See Photo C. Raising the platform will allow access to the cam securement screw and nut. See Photo E. Inner Roll Stop Adjustment CAUTION Do not adjust inner roll stop linkage rod.
Page 9 Inner Roll Stop Adjustment 3. Use an Allen wrench to prevent the cam locking screw from turning and loosen the 3/8 " ser- rated fl ange nut securing the lifting arm cam. See Photos D and E. Do not remove the screw or nut. 4. Raise the platform 1" above fl oor level using the manual operation system .
Page 10 Do not ad- just the in- ner roll stop linkage rod unless extra usable plat- form length is needed. See Photo Linkage rod adjustment affects angle of inner roll stop (vertical position). CAUTION Improper inner roll stop linkage rod adjustment may result in lift damage.
Page 1 1 Inner Roll Stop Occupied Sensor Adjustment 1. The optimum setting for the inner roll stop occupied sensor adjustment nut is to have just enough pressure to fold and unfold the inner roll stop without trigger- ing the inner roll stop occupied sensor .
Page 12 Speci fi ed (recommended) A vailable Braun Lubricant T ype Lubricant Amount Part No. LO - Light Oil SG - Synthetic Grease Synthetic Grease Mobiltemp SHC32 12.5 oz. (Multipurpose) T ube Light Penetrating Oil LPS2, General Purpose 1 1 oz. (30 weight or equivalent) Penetrating Oil Aerosol Can Stainless Stick Door-Ease 1.
Page 13 Maintenance and Lubrication Schedule Maintenance and lubrication procedures must be performed as speci fi ed by an authorized service technician. Failure to do so may result in serious bodily injury and/or property damage. W A RN I N G Proper maintenance is necessary to ensure safe, trouble free operation.
Page 14 Maintenance and Lubrication Schedule 1500 Cycles 750 Cycles Apply Light Oil - See Lubrication Diagram Apply Door-Ease - See Lubrication Diagram.
Page 15 Maintenance and Lubrication Schedule Hydraulic Fluid (Pump) - Check level. Note: Fluid should be changed if there is visible contamina- tion. Inspect the hydraulic system (cylinder , hoses, fi ttings, seals, etc.) for leaks if fl uid level is low .
Page 16 T r oubleshooting Diagnosis Chart 1.00 NO OPERA TION 2.1 1 Hydraulic Down valve open 2.12 Pump mounted horizontal 2.13 No oil (low) 1.1 1 Low battery 1.
Page 17 FUNCTION POSSIBLE CAUSE REMEDY 4.1 1 Outer Barrier switch is out of adjustment or defective. 4.12 Full Out switch is not activated or defective. 4.13 Hand-held pendant not working properly . 4.00 LIFT WILL GO UP WITH OVERRIDE SWITCH BUT NOT WITH HAND-HELD PENDANT Check diagnostic LCD for Outer Barrier switch sta- tus.
Page 18 FUNCTION POSSIBLE CAUSE REMEDY 9.00 BARRIER WILL NOT OPERA TE UP OR DOWN WITH OVER- RIDE SWITCHES OR HAND-HELD PENDANT 9.12 Poor plug connections 9.13 Barrier actuator motor or actuator out of adjustment or faulty 9.14 Bad power and ground Check harness connectors A1 and A2, E1, N1, N2, E1, F1 and F2.
Page 19 CONT ACT REMOV AL 1. Remove orange wedge using needle nose pliers or a hook shaped wire to pull wedge straight out. 2. T o remove the contacts, gently pull wire backwards, while at the same time releasing the locking fi nger by moving it away from the contact with a screwdriver .
Page 20 NOTES This page intentionally left blank..
Page 21 Wiring Schematic NUVL PC BOARD #100419-001 #100439-001 SWITCH BOX LIFT 6 5 4 3 J2 3 P2 2 6 5 4 2 1 1 5 6 J4 3 4 2 1 YL GN RD BK WH 5 6 P4 3 4 2 1 BU NOT USED NOT USED WH GN OR BU/BK NOT USED B.
Page 22 Unfold for: Lift Wiring Schematic Hydraulic Parts List Item Qty . Description Part No. 1 1 Pump Assembly (M259 with Reservoir/ with Back-up pump) 87060-24V 2 1 Motor , Pump 16504-IS 3 1 V alve.
Page 23 Hydraulic Diagram 34 28 29 30 32 35 35 31 26 18 25 33 33 19 21 22 23 24 17 34 27 28 29 Front Cylinder Rear Cylinder 14 1 2 3 6 5 4 16 9 10 11 15 7 12 8 11 13 38 39 40 17 Arrow must face pump A.
Page 24 Pump Module Parts List DESCRIPTION PA RT N O . QTY ITEM ASSY -BOX-BRAUN HYDRAULIC & CONTROLS 22-01-1045A 1 1 BRACKET -PC BOARD MOUNTING/WMT 73824W 1 2 LAMP-BICOLORED LED P ANEL 30728 1 3 S.
Page 25 Pump Module Diagram 30 52 6 42 38 39 31 29 28 41 35 9 2 11 4 50 43 44 24 27 12 16 40 25 47 53 45 1 18 26 21 20 22 23 17 19 14 13 10 15 36 37 33 32 34 3 7 8 48 49 5 51.
Page 26 Exploded Views and Parts Lists Housing Assembly Parts List MANUAL RELEASE CABLE ASSY KIT 73770-600 1 9 BLOCK-CARRIAGE STOP 1 1 75781N CLAMP-INSULA TE 1" 1 2 20535 1 3 73706 NUT 1/2-20 HEX JAM-AUT/BLK.
Page 27 Exploded Views and Parts Lists Housing Assembly 20 37 16 27 5 5 40 38 23 38 27 39 2 14 8 4 25 39 15 15 22 17 19 31 14 42 42 42 27 14 14 14 9 36 14 14 18 14 14 14 14 14 14 14 30 14 41 41 41 38 .
Page 28 Exploded Views and Parts Lists Carriage Assembly Parts List BEARING OUTER RACE ASSEMBL Y 75230RMA 2 9 CARRIAGE WELDMENT 1 1 75201RMNW BEARING TRACK ROLLER 20X52 4 2 84305 1 3 75801RFNA NUT 1/4.
Page 29 Exploded Views and Parts Lists Carriage Assembly 37 50 45 47 49 27 3 29 25 25 25 25 19 39 41 12 2 17 23 24 14 21 40 42 2 28 20 14 54 54 54 36 15 46 4 21 49 34 32 33 53 2 22 46 43 46 51 13 1 12.
Page 30 Exploded Views and Parts Lists Platform Assembly Parts List - Main Note: See pages 32-34 for other platform assembly breakdowns. SCREW-10-32 X 3/8 PHP ZP THD CUT 82755 6 9 PLA TE-PLA TFORM FLOOR 1 1 75306RMGMG COVER-PLA TFORM WIRING HARNESS 1 2 75738RMNY 1 3 75317RN BEARING-.
Page 31 Exploded Views and Parts Lists Platform Assembly - Main 33 10 17 42 21 13 36 26 34 3 12 11 43 5 4 13 9 4 6 2 35 8 22 23 32 15 20 45 40 41 38 39 7 1 28 27 13 14 37 29 13 14 18 25 6 28 16 16 44 30 19 13 9 31 9 9 9 18 25 24 Note: See pages 32-34 for other platform assembly breakdowns.
Page 32 Exploded Views and Parts Lists Platform Assembly - Inner Roll Stop Platform Assembly - Outer Barrier 1 5 4 3 6 8 9 7 10 2 2 ASSY -DUAL OUTBOARD BARRIER 75321RNA WMT -BARRIER DESCRIPTION 82771 83585 PA RT N O . 75321RMNW ITEM 4 3 2 1 6 5 1 1 2 QTY .
Page 33 Exploded Views and Parts Lists Platform Assembly - Fr ont Handrail Platform Assembly - Rear Handrail 1 9 16 10 7 10 4 13 15 13 13 12 12 14 5 6 11 14 15 4 SCREW-#8-18 X 1/2" PH/PN SD-SS 18533 NUT -3/8-16 UNC HEX NYLOCK DESCRIPTION 34032A 10091 PA RT N O .
Page 34 Exploded Views and Parts Lists Platform Assembly - Fr ont Handrail Lock Platform Assembly - Rear Handrail Lock 6 4 3 1 7 2 5 BAR-HANDRAIL LOCK REAR 33478 WELDMENT -HANDRAIL LA TCH REAR DESCRIPTION 33668 33669 PA RT N O . 34178W ITEM 4 3 2 1 6 5 6 1 3 QTY .
Over 300 Braun Dealers W orldwide "Pr oviding Access to the W orld" ® "Pr oviding Access to the W orld" International Corporate Hdqrs: P .
Public Use Wheelchair Lifts All illustrations, descriptions and specifications in this manual are based on the latest pr oduct information available at the time of publication. The Braun Corporation reserves the right to make changes at any time without notice.
デバイスBraun NUVL855RM24の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Braun NUVL855RM24をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBraun NUVL855RM24の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Braun NUVL855RM24の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Braun NUVL855RM24で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Braun NUVL855RM24を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBraun NUVL855RM24の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Braun NUVL855RM24に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBraun NUVL855RM24デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。