BuffaloメーカーNetwork USB Print Server LPV3-U2の使用説明書/サービス説明書
ページ先へ移動 of 24
Unpacking and Setup This section provides unpacking and setup information for the USB Print Server . Unpacking Open the shipping carton of the USB Printer Server and carefully unpack its contents.
2 Insert the included CD into a CD-ROM Drive. Run the setup.exe program found on the root of the CD. This can be done by browsing to the CD or by going to the ‘Start Menu’, selecting ‘Run...’ , and typing x:setup.exe (Where x is the drive letter of the CD-ROM Drive), then press the ‘ OK ’ button.
3 Press the ‘ Browse ’ button if there is a specific location the manager should be installed to. Otherwise press the ‘ Next ’ button and accept the default installation location. The installation will continue and copy files to their necessary locations.
4 Using the Software Launch the software by finding the icon in the Start Menu. Press the ‘Start’ button, select ‘Programs’, select ‘BUFF ALO’, select ‘LPV3 Manager ’, and finally press the ‘ LPV3 Manager ’ icon. The LPV3 Manager will launch and search for the USB Print Server on the network.
5 Configure the USB Print Server by double-clicking on the corresponding Print Server . This will open the USB Print Server ’ s properties. The name of the USB Print Server can be changed by entering a new name in the ‘ Server Name ’ field. The Password and Port names can also be changed if desired.
6 T o configure the protocol settings press the ‘ Protocol Settings ’ tab. The protocol options are TCP/IP , AppleT alk, NetBEUI, and SNMP . T o configure a protocol, select it and press the ‘ Properties ’ button. TCP/IP Settings: Select the ‘ Manual Setting ’ option from the drop-down menu if a specific IP address is desired.
7 AppleT alk Settings: If there are Macintosh computers on the network that wish to use the printer , then enter a ‘ Rendezvous Service Name ’ in the field and press the ‘ OK ’ button. This name is the friendly name Mac users will see when installing their printer .
8 T o view information about the USB Print Server , press the ‘ Information ’ tab. This tab will display the current information about the USB Print Server . T o reset the device or to restore the factory default settings, press the ‘ Reset ’ tab.
9 Open the ‘Printers and Faxes’ folder . T o do so, open the ‘ Control Panel ’ and then open the ‘ Printers and Faxes ’ folder . Double click on the ‘ Add Printer ’ icon. This will open the ‘Add Printer Wizard’. Press the ‘ Next ’ button.
1 0 Select ‘ Create a new port: T ype of port: ’. From the pull down list, select ‘ Standard TCP/IP Port ’. Press the ‘ Next ’ button. The ‘Add Standard TCP/IP Printer Port Wizard’ will open. Press the ‘ Next ’ button. Enter the IP address of the USB Print Server into the field called ‘ Printer Name or IP Address: ’.
1 1 The ‘Additional Port Information Required’ window will appear . Select ‘ Standard ’ device type and select ‘ Generic Network Card ’ from the pull down menu. Press the ‘ Next ’ button when finished. A summary screen will appear . Press the ‘ Finish ’ button to continue setting up your USB Network Printer .
1 2 The ‘Name Y our Printer ’ window will appear . Enter an appropriate name or leave the default ‘Printer name’ if desired. Also, select if the printer is to be the default printer or not. Press the ‘ Next ’ button when complete. The ‘Printer Sharing’ window will appear .
1 3 Open the ‘Printers’ folder . T o do so, open the ‘ Control Panel ’ and then open the ‘ Printers ’ folder . Double click on the ‘ Add Printer ’ icon. This will open the ‘Add Printer Wizard’. Press the ‘ Next ’ button. Y ou will be prompted to select the type of printer to be installed.
1 4 The ‘Browse’ dialog window will appear . Browse for the appropriate printer , select it, and press the ‘ OK ’ button. NOTE : If an error is displayed while browsing for the printer , then there is a network problem, or a problem with the ‘PortName’ set on Page 5 .
1 5 The ‘Printer Name’ window will appear . Enter an appropriate name for the printer and press the ‘ Finish ’ button. The USB Network Printer is now installed. A test print can verify that the printer is installed correctly . Find the printer in the Printer ’ s folder , right click on its icon and select ‘ Properties ’.
1 6 IPP requires a full time internet connection at the location where the printer is installed. Port 631 is the default port for IPP . The router on the network needs to pass port 631 through to the local IP address of the USB Print Server . Please see the documentation for the router to setup port forwarding properly .
1 7 Select ‘ A network printer , or a printer attached to another computer ’. Press the ‘ Next ’ button. Select ‘ Connect to a printer on the Internet or on a home or office network: ’. In the ‘URL ’ field, enter: http://IP_ADDRESS:631/POR TNAME (using the ‘Port’ name from Page 5 ).
1 8 The ‘Install Printer Software’ window will appear . Please select the proper printer from the list below , or refer to the printer manufacturer ’ s driver location. Once the proper printer driver has been selected, press the ‘ Next ’ button.
1 9 It is recommended that you connect the print server directly to your Apple computer using a cross over Ethernet Cable or connect the Apple computer and the print server to a hub or switch, to perform the initial configuration.
2 0 The Basic Settings menu will appear . Enter an acceptable Print Server Name. This can be left as default if desired. The W eb-based Configuration system can be password protected by entering and verifying a new password. Press the ‘Set’ button when configuration is complete.
21 Rendezvous is enabled by default so if you are using this service in your network, the server will be discovered. If used, enter AppleT alk info, otherwise leave in default condition. After entering your settings, press the ‘Set’ button. For further information please click on the ‘?’ icon next to the area in question.
22 Installing the Printer on your Macintosh Open the ‘ System Preferences ’ from the Apple menu and select ‘ Print & Fax ’. The ‘Print & Fax’ window will appear . Press the ‘ Set Up Printers... ’ button. The ‘ Printer List ’ will appear .
23 Press the ‘ Printer Model ’ pull down menu and select the proper hardware driver for the printer . The printer ’ s CD-ROM may be needed to install the proper drivers if they’re not already supplied. In this case, select the ‘ Other ... ’ option and provide the location of the proper driver fi le.
24 T echnical S uppor t Buf falo T echnology offers toll-free technical support 24 hours a day , 7 days a week for this product. Customers in the United States and Canada can obtain technical support using the following information: W eb: www .buf falotech.
デバイスBuffalo Buffalo Network USB Print Server LPV3-U2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Buffalo Buffalo Network USB Print Server LPV3-U2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBuffalo Buffalo Network USB Print Server LPV3-U2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Buffalo Buffalo Network USB Print Server LPV3-U2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Buffalo Buffalo Network USB Print Server LPV3-U2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Buffalo Buffalo Network USB Print Server LPV3-U2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBuffalo Buffalo Network USB Print Server LPV3-U2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Buffalo Buffalo Network USB Print Server LPV3-U2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBuffalo Buffalo Network USB Print Server LPV3-U2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
