Buffalo TechnologyメーカーWMR-G54の使用説明書/サービス説明書
ページ先へ移動 of 20
54Mbp s/1 1Mbp s Wireless ADSL Modem Router WMR-G54 User ’ s Guide.
2.
T able of Content s Introduction 3 A Look at the Hardware 3 Front Panel 4 B a c k P a n e l 4 Hardware Installation 5 Configure the Router for the first time 5 Configuring IP Settings on Y our Compute.
following table defines the behavior for each LED: LED Represent s Activity / S tatus Power Power The Power LED will light up when the device is powered on. USB USB Connection - S teady on – USB is connected to a host PC. - Blinking – Dat a is being transferred over the USB connection.
cable to the USB port an d connect the other end to the computer . Reset Use an object, such as a stretched p aper clip, to press the button for at l east 3 seconds. LAN 1, 2, 3, 4 LED will light up for a short time and then be off. Y ou can release the button now to reset the device to its factory-default settings.
For Windows 2000/Windows XP 1. Right-click on My Network Places icon on the desktop and then click Properties in menu. 2. Double-click Local Area Connection icon and then click Properties button. 3. Scroll down to highlight TCP/IP (y our netw ork card) and then click Properties button.
Internet Service Provider (ISP). The ADSL Modem Router can be configured with your web browser . The product provides a very easy and user-friendly interface for configuration. 1. Open your web browser . En ter http://192.168.1.1 in the web browser ’s address field, and press the enter key .
II. Quick Setup The Quick Setup will guide you through the steps necessary to configure your DSL Router . III. Configure W AN (DSL) Connectivity 1. Click the Advanced Setup tab on the left frame. 2. Click the WA N tab on the lef t frame. A W AN Setup pag e will appear on the right frame.
UBR With PCR, CBR, Non Realtime VBR, and Realtime VBR. 4. A Connection T ype page will appear . There are several ways for the device to have a public IP address and then to access the Internet. Y ou have to check with your ISP about which way is adopted.
2. In the PPP Username and Pa ssword page, enter the user name and password supplied by your ISP in PPP Username and PPP Passw ord fields. 3. Check the box Disconnect if no activity if you want to enable the function of automatic disconnection. It will auto-disconnect the ADSL Modem Router when there is no activity on the line for a period of time.
Allows only one PC on the LAN The public IP address assigned by the remote using the PPP/IPCP protocol is actually not used on the W AN PPP interface.
7. The W AN Setup page will appear . Click the Save/Reb oot button. The router will reboot automatically with the new settings in effect. 8. Close your Web UI window and wait for about 2 minutes before reopening your web browser .
IP over A TM (IPoA) 1. Select the IP over A TM (IPoA) radio button and scroll down to select the appropriate Encap sulation Mode . There are two encapsulation types available: LLC/Snap-Routing and VC/MUX. Then click Next button. 2. DHCP is n ot supported over IpoA.
3. The Network Address T ranslation Settings page will appear . If you want to enable the NA T function, check the box Enable NA T . If NA T is enabled, it will display a NA T submenu on the left p anel after the unit reboots. NA T occurs when multiple IP addresses on a private LAN are converted to one public address.
8. The W AN Setup – Summary page displays a summary of all W AN setting profiles. Click the Save button to save all the settings. 9. The W AN Setup page will appear . Click the Save/Reb oot button. The router will reboot automatically with the new settings in effect.
2. Check the box Enable Bridge Service . Enter a desired name in the Service Name field. It is used to identify the service. Then click the Next butto n. The LAN IP in bridge operating mode is needed for local users to manage the ADSL Modem Router . And no IP address is needed for the W AN in bridge mode.
4. The W AN Setup page will appear . Click the Save/Reb oot button. The router will reboot automatically with the new settings in effect. 5. Close your Web UI window and wait for about 2 minutes before reopening your web browser .
IV . Configure Wireless Connectivity 1. Click the Wireless tab on the left frame. A Wireless - Basic page will appear on the right frame. Check the box Enable Wireless . 2. Check the box Hide Access Point and then your WMR-G54 will not res pond when a ping is sent by any user on the Internet.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove pr esu.
Buffalo T echnology Europe Buffalo T echnology UK 176, Buckingham Avenue Slough, Berkshire, SL1 4RD United Kingdom T el. +44 (0) 1753 555000 Fax. +44 (0) 1753 535420 Buffalo T echnology Ireland Free Zone East Shannon Co. Clare Ireland T el. +353 61 708090 Fax.
デバイスBuffalo Technology WMR-G54の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Buffalo Technology WMR-G54をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBuffalo Technology WMR-G54の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Buffalo Technology WMR-G54の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Buffalo Technology WMR-G54で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Buffalo Technology WMR-G54を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBuffalo Technology WMR-G54の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Buffalo Technology WMR-G54に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBuffalo Technology WMR-G54デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
