BunnメーカーG9WD-RHの使用説明書/サービス説明書
ページ先へ移動 of 15
G9WD-RH INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest.
2 41451.0001 041410 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years.
3 USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. #20545.0000 CONTENTS Introduction .
4 ELECTRICAL REQUIREMENTS This grinder has an attached cord set and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. OPERA TING CONTROLS Grind Pad (a) Pressing initiates a grind cycle. Stop Pad (b) Pressing ends the operation of the grinder .
5 COFFEE GRINDING 1. Visually inspect the hopper for an ample supply of whole bean coffee. 2. Place a paper filter into the brew funnel. The filter must not be folded-over or tilted to one side. 3. Insert the funnel into the funnel rails until it stops.
6 CLEANING WARNING – Unplug grinder before the removal of any panel or grind chamber -housing parts. 1. Clean all exterior surfaces using a damp cloth rinsed in any mild, nonabrasive, liquid detergent. Care should be taken not to scratch the grinder with any abrasive material.
7 GLOSSAR Y GRIND OZ: ##.## (-) DONE (+) Adjust current weight setting using (-) and (+) buttons Allows adjustment of current time setting Adjust current time setting us- ing (-) and (+) buttons Allow.
8 GROUND COFFEE COUNTER The grinder will keep a running total of the pounds of coffee the grinder has ground. This running total is shown in the “PmBurrsLbs #” menu, under the “SERVICE TOOLS” menu. This running total can be used to determine when the grinding burrs need cleaning or replacement.
9 COMMUNICA TING WITH THE GRINDER Press the hidden (copyright) button for 1 second Press right hidden (copyright) button to scroll to next screen Press right hidden (copyright) button to scroll to nex.
10 COMMUNICA TING WITH THE GRINDER (Continued) From previous page Loop back to “COFFEE NAME” Press “GRIND” button to start coffee calibration The small batch size will flash, press (-) or (+) to adjust grind weight. After first batch size is set, additional batch sizes can be set by pressing appropriate batch size button.
11 COMMUNICA TING WITH THE GRINDER (Continued) Pressing any switch in this mode will display the switch name in the grinder display . After the funnel is “tared” add a calibrated weight to check scale.
12 COMMUNICA TING WITH THE GRINDER (Continued) LEVEL 2 FUNCTIONS: Press the hidden (copyright) button for 3 seconds in “ENTER P ASSWORD” menu. Finished, returns to main screen MODIFY MAXBIT NO SPREAD? YES CALIBRA TE SCALE ? NO YES MACHINE TYPE WEIGHT TIMED SHUT off Bits ## (-) DONE (+) MaxBits read # (-) DONE (+) PLEASE WAIT CAL PLACE 8.
13 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department.
14 Check that relay contacts close when start switch is pressed. With a voltmeter , check that 120 volts AC is present across L1 and L2 on the rear of the motor when the Start switch is pressed. If volt- age is present, and motor does not start, replace motor .
15 BLK WHT RED RED VIO BLK BLK VIO VIO K1 N.O. M K1 BLK WHT L1 N L1 L2 1 4 J1 CONTROL CIRCUIT BOARD LOAD TRANSDUCER BLK GRN WHT RED 1 4 J7 GRN SCHEMA TIC WIRING DIAGRAM G9WD-RH 120 VOL TS AC 2 WIRE SI.
デバイスBunn G9WD-RHの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bunn G9WD-RHをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBunn G9WD-RHの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bunn G9WD-RHの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bunn G9WD-RHで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bunn G9WD-RHを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBunn G9WD-RHの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bunn G9WD-RHに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBunn G9WD-RHデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
