Bush Hogメーカー280の使用説明書/サービス説明書
ページ先へ移動 of 23
BU S H H O G ® ASSEMBL Y ● OPERA TION ● MAINTENANCE $4.00 Operator ’s Manual 280 SERIES R OT AR Y CUTTERS 199 P art No. 95355.
CONGRA TULA TIONS! Y ou ha ve inv ested in the best implement of its type on the mar ket toda y . The care you giv e your Bush Hog implement will greatly determine your satisf action with its perf or mance and its ser vice lif e.
280 SERIES ROT AR Y CUTTERS T ABLE OF CONTENTS SECTION/P ARA P A GE W arranty .................................................3 Dealer Preparation Chec k List ...............4 Saf ety Precautions .................................5 F ederal La ws and Regulations.
BUSH HOG ® MODEL 280 SERIES LIMITED W ARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush.
DEALER PREP ARA TION CHECK LIST 280 SERIES RO T AR Y CUTTERS BEFORE DELIVERING MA CHINE — The f ollowing chec k list should be completed. Use the Operator’ s Manual as a guide . ❒ 1. Assembled completed. ❒ 2. Gearbo x filled with oil. ❒ 3. All fittings lubricated.
IMPOR T ANT SAFETY PRECA UTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury.
IMPOR T ANT FEDERAL LA WS AND REGULA TIONS* CONCERNING EMPLO YERS, EMPLO YEES AND OPERA TIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your 280 Series Rotary Cutter has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition.
Figure 2-1 Top Link Pin 5-1/2” 3-3/4” 3-3/4” 8 NOTE Due to the many variations in tractor / imple- ment hitch points and corresponding differ- ences in distances between tractor PTO shafts and i.
9 Figure 2-3 H. Hold driveline sections parallel to each other and check for minimum 6 inches (15cm) overlap. Figure 2-4). If driveline has been marked for cutting, overlap will be the distance between two marks. If driveline has less than minimum overlap, do not use.
SECTION III OPERA TING INSTR UCTIONS 3-1 GENERAL SAFETY Only qualified people should operate this machine. Operator should wear hard hat, safety glasses and safety shoes. It is recommended that tractor be equipped with Rollover Protective Systems (ROPS) and a seat belt be used.
ROTATING CUTTER BLADES. STAND CLEAR UNTIL ALL MOTION HAS STOPPED. TO AVOID AN ACCIDENTAL FALL FROM THE TRACTOR AND POSSIBLE INJURY BY THE MOWER, IT IS RECOMMENDED THAT THE TRACTOR BE EQUIPPED WITH ROPS (ROLLOVER PROTECTIVE SYSTEM) AND THAT A SEAT BELT BE USED BY THE OPER- ATOR FOR ALL MOWING OPERATIONS.
12 Figure 4-1 Lubrication (3) Before Each Use (2) Before Each Use (6) Before Each Use 4-4 BLADE REPLA CEMENT (Figure 4-2) It is not necessary to remove the complete blade holder assembly to replace the blades. Blade bolts are accessible through a hole in the top of the cutter deck.
(See Chart) Figure 4-3 Spring Length MODEL SPRING LENGTH 285 &286 1-3/32” or 27.6 mm 287 1-1/8” or 28.5 mm 13 turning blades. If clutch does not slip, contact your authorized Bush Hog dealer. C. Retighten nuts to within 1/64” of original posi- tion.
PRE-ASSEMBL Y SAFETY PRECA UTIONS THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to protection for eyes, ears, feet, hands, lungs and head when assembling the equipment.
SECTION V ASSEMBL Y IMPORTANT Tighten all fasteners to specifications on Torque Chart unless otherwise indicated. 5-1 3-POINT LIFT MODELS (285 & 286) A. Attach A-frame struts to mounting brackets using 5/8” x 2” capscrews and locknuts as shown.
5-2 3-POINT LIFT MODELS (287) A. Attach A-frame struts to mounting brackets using 5/8” x 2” capscrews and locknuts as shown. (Fig. 5-1) B. Place flex link and pivot tube between top of A- frame struts. Place support yokes on outside of A- frame struts.
5-3 SEMI-MOUNT MODEL (287) A. For mounting dual tailwheels, position tailwheel brackets at the rear tubes located in the strong- backs. (Figure 5-2) Align holes in tailwheel weld- ment with holes in strongback. Install pivot bushings and fasten with 3/4” x 8” capscrews and flange lock- nuts.
18 5-5 FRONT BEL TING INST ALLA TION A. Align belting and clamp with holes in front lip of deck. B. Fasten with 3/8 x 3-1/2” capscrews, flatwash- ers, lockwashers and nuts. (Figure 5-4) 5-6 REAR B AND INST ALLA TION A. Align deflector band with holes in rear band of deck.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge.
T ORQ UE SPECIFICA TIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.
MODEL 287 QUICK HITCH ASSEMBL Y NOTE Pivot arm must be assembled as shown so that it will pivot upward as the hitch assembly flexes. Pointed end must be to the top.
DIVISION OF P .O . Bo x 1039 ● Selma, AL 36702-1039 T elephone (334) 872-6261 BUSH HOG.
デバイスBush Hog 280の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bush Hog 280をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBush Hog 280の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bush Hog 280の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bush Hog 280で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bush Hog 280を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBush Hog 280の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bush Hog 280に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBush Hog 280デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。