Bush HogメーカーSM 60の使用説明書/サービス説明書
ページ先へ移動 of 26
OPERATION l l MAINTENANCE 1007 $4.00 97701 M o d e l S M 6 0 S i d e M o u n t R o t a r y C u t t e r O p e r a t o r ’ s M a n u a l B U S H H O G ®.
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life.
RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY It is the Retail Customer and/or Operator’s responsibility to read the Operator’s Manual, to operate, lubricate, maintain and store the product in accordance with all instructions and safety procedures.
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog war rants to the original purchaser of any new Bush Hog equipment, purc hased from an authorized Bush Hog dealer, that the equipment be free f.
DEALER PREPARATION CHECK LIST SM60 ROTARY CUTTER BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. r 1. Assembled completed. r 2. Gearbox filled with oil. r 3. All fittings lubricated. r 4.
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury.
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
SECTION I INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your Side Mount Rotary Cutter, Model SM60,has been carefully designed to assure maxi- mum service with minimum down time.
TABLE 1-1 SPECIFICATIONS (For Cast Iron Pump & Motor Only) MODEL NUMBER SM60R SM160R Required PTO Speed 540 rpm 1000 rpm Pump Output 21.4 gpm 19.1 gpm Motor Speed 1101 rpm 1182 rpm Blade Tip Speed 17,300 18,570 ft. / min. ft. / min. Blade Type 1/2” x 3” 1/2” x 3” Dble.
F. Pull driveline apart. Attach the outer (female) section to the tractor PTO shaft and the inner (male) section to the pump input shaft. Pull on each drive- line section to make sure yokes lock into place. G. Hold driveline sections parallel to each other to determine if driveline is too long.
G. Repeat steps “E” and “F” to other driveline sec- tion. H. De-burr the ends of the drivelines and clean away all chips and filings. (Fig. 2-7) I. Apply grease to inside of outer (female) driveline section. Reassemble driveline and attach to tractor and implement.
KEEP CLEAR OF MACHINE WHEN RAISING AND LOWERING THE CUTTER HEAD. D. Place cutter deck in desired working position. E. Engage PTO drive with tractor at idle speed. Allow 2-3 minutes for hydraulic fluid to warm up. KEEP HANDS AND FEET FROM UNDER CUT- TER AT ALL TIMES TO AVOID SERIOUS INJURY.
3-5 STORAGE A. Apply light coat of multi-purpose grease to slid- ing assemblies. B. Perform steps “A” through “G” in paragraph 3-4. C. Relieve hydraulic pressure by shifting imple- ment control valve levers back and forth. D. Disconnect implement hydraulic lines connect- ed to tractor.
EVERY 150 HOURS 1. Cables - Wearing gloves, wipe cables with an oil soaked rag. YEARLY 1. Hydraulic Tank - Drain hydraulic tank while oil is warm.Clean suction strainer and filler strainer with compressed air. Replace return line filter. Refill tank with hydraulic oil.
4-4 BLADE HOLDER REMOVAL (Fig. 4-3) THE CUTTER CAN FALL FROM HYDRAULIC SYSTEM FAILURE. TO AVOID SERIOUS INJURY OR DEATH, SECURELY SUPPORT CUTTER BEFORE WORKING UNDERNEATH.
D. Turn motor 180º. Reinstall bolts retaining motor to spindle housing. E. Reinstall hydraulic fittings, and hoses. Replace fitting O-rings as necessary. 4-10 TROUBLESHOOTING Cleanliness is of primary importance for obtaining satisfactory life of hydraulic components.
Table 4-4 General Troubleshooting TROUBLE PROBABLE CAUSE REMEDY 1. Hydraulic Pump Noisy Cavitation Check condition of suction strainer and return line filter. Clean or replace as necessary. Check for clogged or restricted inlet line to pump. Check for loose fittings on suction line.
SECTION V ASSEMBLY THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to protection for eyes, ears, feet, hands, lungs and head when assembling the equipment.
5-1 BASIC MACHINE ASSEMBLY BASE UNIT IS EXTREMELY TOP HEAVY WHEN DISCONNECTED FROM CUTTER DECK AND SHOULD BE MOVED ONLY BY CONNECTING TO TRACTOR 3-POINT HITCH. DO NOT REMOVE WOODEN SUPPORT UNLESS UNIT IS CONNECTED TO TRACTOR 3-POINT HITCH OR OVER- TURNING WILL RESULT.
USE OF THIS MACHINE ON TOO SMALL A TRACTOR CAN CAUSE TRACTOR UPSET. DO NOT USE THIS MACHINE ON A TRACTOR WEIGHING LESS THAN 6000 LBS. (2722 kg), NOT INCLUDING BALLAST. IT IS RECOM- ME N DE D TH AT FRO NT BAL LA S T BE U SE D FOR ADDED STEERING STABILITY.
5-5 OPTIONAL TAILWHEEL INSTALLATION A. Position mounting bracket against underside of frame as shown. (Fig. 5-6) B. Position mounting plate on top side of frame and fasten with four 5/8 x 7-1/2” bolts and locknuts. C. Apply warning decal to top of tailwheel beam.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge.
SAFETY DECALS CONTINUED 21 83373 83375 82617 83374 83377.
B O L T D I A M E T E R W R E N C H ( I N . ) “ B ” A N D S A E S A E S A E S I Z E ( I N . ) “ A ” T H R E A D S I Z E G R A D E 2 G R A D E 5 G R A D E 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (1.
P.O. Box 1039 l l Selma, AL 36702-1039 Telephone (334) 874-2700 l l www.bushhog.com.
デバイスBush Hog SM 60の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bush Hog SM 60をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBush Hog SM 60の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bush Hog SM 60の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bush Hog SM 60で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bush Hog SM 60を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBush Hog SM 60の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bush Hog SM 60に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBush Hog SM 60デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
