Cabletron SystemsメーカーFPIM-02の使用説明書/サービス説明書
ページ先へ移動 of 26
9032531-01 SmartSwitch 9000 9M426-02 User’s Guide.
.
i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made.
Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation.
iii Notice DECLARA TION OF CONFORMITY ADDENDUM Application of Council Directi ve(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representati ve Name: Mr.
Notice iv.
v Contents Chapter 1 Intr oduction Features........................................................................................................................... 1-1 Related Manuals ................................................................
Contents vi.
1-1 Chapter 1 Intr oduction The 9M426-02 SmartSwitch Module shown in Figure 1-1, is a thr ee port switch module with two front panel HSIM interfaces and one INB-2 backplane interface. W ith the proper HSIM, this module may be used as an A TM uplink for the SmartSwitch 9000 chassis.
Introduction 1-2 Connectivity The 9M426-02 module has one interface to the INB-2 and two front panel HSIM interfaces. Management Information Base (MIB) Support For a complete list of supported MIBs, refer to the r elease notes provided in the 9M426-02 package.
1-3 Introduction Figure 1-1. The 9M426-02 Module SMB CPU INB 9M426-02.
Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedur es and technical data contained in this manual. SmartSwitch 9000 Installation Guide SmartSwitch 9000.
2-1 Chapter 2 Installing the Smar tSwitch 9000 Module This module uses HSIMs for the front panel connections. They ar e not shipped with the module and must be purchased separately . For installation information, refer to the manual supplied with the HSIM.
Installing the Smar tSwitch 9000 Module 2-2 Figure 2-1. User Accessible Components SMB-1 PROM Flash SIMM So cke t Local DRAM So cke t i960 Processor DIP Switch 1 2 3 4 5 6 7 8 Boot PROM.
2-3 Installing the Smar tSwitch 9000 Module An eight position DIP switch is located on the module car d as shown in Figure 2-1. The function of the switches ar e listed in T able 2-1.
Installing the Smar tSwitch 9000 Module 2-4 Installing the Module into the Smar tSwitch 9000 Chassis T o install the SmartSwitch 9000 module, follow the steps below: 1. Remove the blank panel covering the two slots in which the module is being installed.
2-5 Installing the Smar tSwitch 9000 Module Figure 2-2. Installing the 9M426-02 Module 7 FLNK 8 FLNK FLNK 10 FLNK INS 11 FLNK INS 12 RX TX RX TX RX Circuit Card Card Guides Metal Back-Panel Jack for ESD wrist strap W arning: Ensure that the circuit card is between the card guides .
Installing the Smar tSwitch 9000 Module 2-6 The Reset Switch The Reset switch is located under the top plastic tab as shown in Figure 2-3. Use the reset switch to r eset the module’s processor , shutdown (power down) the module, and/or restart the module.
3-1 Chapter 3 Operation The 9M426-02 FDDI SmartSwitch Module is a three port switch module with two front panel HSIM interfaces and one INB-2 backplane interface. This module, with the proper HSIM, may be used for an FDDI, A TM, W AN and other high-speed connectivity for the SmartSwitch 9000 chassis.
Operation 3-2 band from user data. Modules which shar e the SMB-10 bus periodically send out loop-back packets to ensure the validity of SMB-10. In the event a fault is detected on the SMB-10, the SMB-1 can be used as an alternate communication channel by the modules.
3-3 Operation between the host processor , the INB backplane, and LAN/W AN interfaces on the front panel of SmartSwitch 9000 modules. The SmartSwitch ASIC can operate in two modes: as a traditional switch, or as a SecureFast Switch (SFS).
Operation 3-4.
4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figur e 4-1 is the LANVIEW LEDs of the 9M426-02 module.
LANVIEW LEDs 4-2 The functions of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in T able 4-1. The functions of the INB receive LED ar e listed in T able 4-2. The functions of the INB transmit LED are listed in T able 4-3.
5-1 Chapter 5 Specifications T echnical Specifications CPU Intel i960 RISC based micropr ocessor Memory 4 Meg. Flash Memory (expandable to 8 Meg.) 16 Meg. DRAM (expandable to 32 Meg.) Network Interface Cabletron HSIMs Safety This equipment meets the safety requir ements of: • UL 1950 • CSA C22.
Specifications 5-2 • EMC requir ements of: EN 50082-1 IEC 801-2 ESD IEC 801-3 Radiated susceptibility IEC 801-4 EFT Service MTBF (MHBK-217E) >200,000 hrs. MTTR <0.5 hr . Ph ysical Dimensions 35.0 D x 44.0 H x 6.0 W centimeters (13.8 D x 17.4 H x 2.
デバイスCabletron Systems FPIM-02の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cabletron Systems FPIM-02をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCabletron Systems FPIM-02の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cabletron Systems FPIM-02の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cabletron Systems FPIM-02で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cabletron Systems FPIM-02を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCabletron Systems FPIM-02の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cabletron Systems FPIM-02に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCabletron Systems FPIM-02デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
