Campbell HausfeldメーカーWG3013の使用説明書/サービス説明書
ページ先へ移動 of 16
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
2 Wire Feed Ar c Welder Torch is “live” (has current potential) at all times when machine is turned on. Always keep a fire extinguisher accessible while performing arc welding operations. ● Before starting or servicing any electric arc welder, read and understand all instructions.
Code for Safety in Welding and Cutting CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3 Cutting And Welding Processes .
and top cover aligning the holes in handle with holes in top cover. 2. Fasten screws through top cover and into handle. WHEEL AND AXLE ASSEMBLY 1. Insert axle supports into slots in the welder housing. 2. Insert axle through the axle supports and firmly push wheels onto axle.
5 WG3013 if the duty cycle is exceeded. Welding operations may continue when the yellow lamp is no longer illuminated. 1. Cut retainer stiffeners and detachable handle away from shield. Trim the excess plastic to remove sharp edges. 2. Insert filter lens.
6 Wire Feed Ar c Welder See application decal inside door of wire feed compartment for proper heat settings. NOTE: These settings are general guidelines only. Heat setting may vary according to welding conditions and materials. 6. Rotate the Wire Speed Control to setting number 5 to start with, then adjust as needed after test weld.
7 WG3013 W elding Guidelines General This line of welding machines can utilize the Flux Cored Arc Welding (Gasless) process or the Gas Metal Arc Welding (MIG) process. The weld must be protected (shielded) from contaminates in the air while it is molten.
work piece material thickness all affect the speed of travel necessary for completing a good weld (See Fig. 11). When the speed is too fast, the bead is narrow and bead ripples are pointed as shown. When the speed is too slow, the weld metal piles up and the bead is high and wide.
ALUMINUM WELDING Any aluminum surface to be welded, must be cleaned thoroughly with a stainless steel brush to eliminate any oxides on the weld and grounding surface. 100% Argon must be used when welding aluminum. If Argon is not used, metal penetration is unlikely.
10 T r oubleshooting Chart - W elder Symptom Possible Cause(s) Corrective Action 1. Duty cycle exceeded 2. Poor ground clamp connection 3. Defective power switch 4. Blown breaker or fuse 1. Wrong size gun tip 2. Gun liner clogged or damaged 3. Gun tip clogged or damaged 4.
11 Limited 5-3-1 W arranty 1. Duration: The manufacturer warrants that it will repair, at no charge for parts or labor, the Welder, Welding Gun, or Cables, proven defective in material or workmanship,.
12 WG3013 Wiring Diagram Wire Feed Ar c Welder DRIVE + M - 1 2 43 DECK S4 GUN WIRE SPEED CONTROL BOARD L1 L2 6 5 4 2 1 ~ T2 +- S5 - + ~ GREEN BLACK WHITE S2 S3 T1 MAX MIN 2 1 GROUND S1 ON/OFF FAN OPENS @ 127 ˚ C S5 NC ~ M Y www.
13 WG3013 www.chpower.com For Replacement Parts, call 1-800-746-5641 Address parts correspondence to: The Campbell Group Attn: Parts Department 100 Production Drive Harrison, Ohio 45030 U.
14 Wire Feed Ar c Welder www.chpower.com 1 Torch assembly and hose (Includes Nos. 2-6, 34, and 50-52) WC600700AV 1 2 Torch body, front and back WC600201AV 1 3 Hanger clip WC600003AV 1 4 Nozzle, Tweco .
15 WG3013 www.chpower.com Glossary of W elding T erms AC or Alternating Current - electric current that reverses direction periodically. Sixty cycle current travels in both directions sixty times per second. Arc Length - the distance from the end of the electrode to the point where the arc makes contact with the work surface.
Wire Feed Ar c Welder 16 www.chpower.com Notes.
デバイスCampbell Hausfeld WG3013の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Campbell Hausfeld WG3013をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCampbell Hausfeld WG3013の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Campbell Hausfeld WG3013の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Campbell Hausfeld WG3013で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Campbell Hausfeld WG3013を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCampbell Hausfeld WG3013の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Campbell Hausfeld WG3013に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCampbell Hausfeld WG3013デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。