Advantechメーカー2006957006 5th Editionの使用説明書/サービス説明書
ページ先へ移動 of 128
PCM-9570/S Socket 370 Celeron™/Pentium ® III SBC with LCD, Ethernet and SCSI User's Manual.
Copyright notice This document is copyrighted, 2000. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
Acknowledgments AMD is a trademark of Advanced Micro Devices, Inc. Award is a trademark of Award Software International, Inc. Cyrix is a trademark of Cyrix Corporation. IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation.
Packing list Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-9570/S all-in-one single board computer • 1 CD disc with utility and drivers • 1 Startup Manual If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Contents Chapter 1 General Information ....................... 1 1.1 Introduction ........................................................................ 2 Highly integrated Socket 370 SBC ...................................... 2 1.2 Features .......
2.9 Floppy drive connector (CN9) ........................................ 17 2.9.1 Connecting the floppy drive ...................................... 18 2.10 Parallel port connector (CN12) ....................................... 18 2.11 Keyboard and PS/2 mouse connector (CN5) .
Chapter 3 Software Configuration ................ 31 3.1 Introduction ...................................................................... 32 3.2 Ethernet software configuration ..................................... 33 Chapter 4 Award BIOS Setup ...
Chapter 6 SCSI Setup and Configurations .. 59 6.1 Introduction ...................................................................... 60 6.2 Before you begin ............................................................... 61 6.3 Basic rules for SCSI host adapter and device installation .
C.8 IDE hard drive connector (CN11) .................................. 92 C.9 Parallel port connector (CN12) ....................................... 93 C.10 Backlight connector (CN13) ............................................ 94 C.11 Peripheral power connector (CN14) .
Tables Table 2-1: Jumpers .............................................................................. 8 Table 2-2: Connectors ......................................................................... 9 Table 2-3: CMOS clear (J1) ...................
Table C-20: CompactFlash card connector (CN21) ......................... 102 Table C-21: PanelLink connector (CN22) ........................................ 103 Table C-22: Fan power connector (FAN1) ....................................... 104 Table D-1: System I/O ports .
Figures Figure 1-1: PCM-9570/S dimensions ................................................... 6 Figure 2-1: Locating jumpers ............................................................. 10 Figure 2-2: Locating connectors (component side) ............
General Information This chapter gives background information on the PCM-9570/S. Sections include: • Introduction • Features • Specifications • Board layout and dimensions CHAPTER 1.
2 PCM-9570/S User's Manual 1.1 Introduction The PCM-9570/S is an all-in-one Celeron ™ /Pentium ® III level single board computer (SBC) with an Ultra2 SCSI controller (PCM-9570S), a 2x AGP LCD controller, a PCI Fast Ethernet interface and one PCI expansion slot.
Chapter 1 General Information 3 1.2 Features • Ultra2 SCSI interface: Supports up to 80 MB/sec transfer rates (PCM-9570S only) • 3D VGA/LCD interface: Supports a 2x AGP interface, 3D 64-bit engine, as well as a 2.
4 PCM-9570/S User's Manual • Serial ports: Four serial ports with +5 V / +12 V power capability (COM1, 3, 4: RS-232; and COM2: RS-232/422/485) • Watchdog timer: Software enabled/disabled. 62-level interval from 1 to 62 seconds. Jumperless selection.
Chapter 1 General Information 5 PCI bus Ethernet interface • Chipset: Realtek RTL8139 PCI-bus Ethernet controller • Ethernet interface: PCI 100/10 Mbps, IEEE 802.
6 PCM-9570/S User's Manual 1.4 Board layout and dimensions Figure 1-1: PCM-9570/S dimensions.
Installation This chapter tells how to set up the PCM-9570/S hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedure.
8 PCM-9570/S User's Manual 2.1 Jumpers The PCM-9570/S has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the b.
Chapter 2 Installation 9 2.2 Connectors On-board connectors link the PCM-9570/S to external devices such as hard disk drives, a keyboard, or floppy drives.
10 PCM-9570/S User's Manual 2.3 Locating jumpers Figure 2-1: Locating jumpers.
Chapter 2 Installation 11 2.4 Locating connectors 2.4.1 Component side Figure 2-2: Locating connectors (component side).
12 PCM-9570/S User's Manual 2.4.2 Solder side Figure 2-3: Locating connectors (solder side).
Chapter 2 Installation 13 2.5 Setting jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
14 PCM-9570/S User's Manual 2.6 CPU installation and upgrading You can upgrade to a higher power Pentium processor at any time. Simply remove the old CPU, install the new one, and set the jumpers for the new CPU type and speed. W arning! Alwa ys disconnect the power cord from y our chassis when you are w orking on it.
Chapter 2 Installation 15 When the CPU is installed, the lever should snap into place at the side of the socket. Note: To remove a CPU, pull the lever out to the side a little and raise it as far as it will go.
16 PCM-9570/S User's Manual 2.7 Installing DRAM (SODIMMs) 2.7.1 Introduction You can install anywhere from 16 MB to 128 MB of on-board DRAM memory using 16, 32, 64 or 128 MB 144-pin SODIMMs (Small Outline Dual In-Line Memory Modules).
Chapter 2 Installation 17 2.8.1 Connecting the hard drive Connecting drives is done in a daisy-chain fashion and requires one of two cables (not included in this packing), depending on the drive size. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector.
18 PCM-9570/S User's Manual 2.9.1 Connecting the floppy drive 1. Plug the 34-pin flat-cable connector into CN9. Make sure that the red wire corresponds to pin one on the connector. 2. Attach the appropriate connector on the other end of the cable to the floppy drive(s).
Chapter 2 Installation 19 2.11 Keyboard and PS/2 mouse connector (CN5) The PCM-9570/S board provides a keyboard connector that supports both a keyboard and a PS/2 style mouse. In most cases, especially in embedded applications, a keyboard is not used.
20 PCM-9570/S User's Manual 2.12.4 Reset switch If you install a reset switch, it should be an open single pole switch. Momentarily pressing the switch will activate a reset. The switch should be rated for 10 mA, 5 V. If you need to make your own cable, you can find the pin assignments for the board ’ s connector in Appendix C.
Chapter 2 Installation 21 2.14 ATX power control connector (CN2, J4) 2.14.1 ATX feature connector (CN2) and power button (J4) The PCM-9570/S can support an advanced power button if an ATX power supply is used. To enable the power button: 1. Take the specially designed optional ATX-to-PS/2 power cable (part no.
22 PCM-9570/S User's Manual 2.15 ATX power on function select (J11) Table 2-5: A T W po wer on function select (J1 1) Default on Default off * J1 1 * default setting Note1: J11 select 1-2, that while A C power is turned on, the system cannot boot up without A TX power s witch button J4.
Chapter 2 Installation 23 T able 2-6: COM2 RS-232/422/485 setting (J10) * RS-232 RS-422 RS-485 J10 * default setting The IRQ and the address range for COM1, 2, 3, 4 are fixed. However, if you wish to disable the port or change these parameters later you can do this in the system BIOS setup.
24 PCM-9570/S User's Manual T able 2-8: COM1 RI pin setting (J6) +5 V J6 +12 V J6 * RI (default setting) J6 T able 2-9: COM2 RI pin setting (J6) +5 V J6 +12 V J6 * RI (default setting) J6 1 2 23 .
Chapter 2 Installation 25 T able 2-10: COM3 RI pin setting (J6) +5 V J6 +12 V J6 * RI (default setting) J6 T able 2-11: COM4 RI pin setting (J6) +5 V J6 +12 V J6 * RI (default setting) J6 1 2 23 24 14.
26 PCM-9570/S User's Manual 2.18 VGA interface connections The PCM-9570/S ’ s PCI SVGA interface can drive conventional CRT displays and is capable of driving a wide range of flat panel displays, including electroluminescent (EL), gas plasma, passive LCD and active LCD displays.
Chapter 2 Installation 27 2.18.4 Panel type select (SW1) SW1 is a 6-pin dip switch for selecting the type of panel and display mode. T able 2-12: Panel type select (SW1) Panel type Pin 1 Pin 2 Pin 3 P.
28 PCM-9570/S User's Manual 2.19 Ethernet configuration The PCM-9570/S is equipped with a high performance 32-bit PCI-bus Ethernet interface which is fully compliant with IEEE 802.3U 10/100Mbps CSMA/CD standards. It is supported by all major network operating systems.
Chapter 2 Installation 29 2.20 Watchdog timer configuration An on-board watchdog timer reduces the chance of disruptions which EMP (electro-magnetic pulse) interference can cause. This is an invaluable protective device for standalone or unmanned applications.
30 PCM-9570/S User's Manual 2.22 SCSI connectors (CN4) The PCM-9570/S has a 68-pin D-sub connector for Ultra2 SCSI devices. Connection of SCSI devices requies special attention, especially when determining the last drive on the SCSI chain. Refer to Chapter 6 and your device ’ s operating manual for detailed installation information.
Software Configuration This chapter details the software configuration information. It shows you how to configure the card to match your application requirements.
32 PCM-9570/S User's Manual 3.1 Introduction The PCM-9570/S system BIOS and custom drivers are located in a 256 Kbyte, 32-pin (JEDEC spec.) Flash ROM device, designated U15. A single Flash chip holds the system BIOS, VGA BIOS, and network Boot ROM image.
Chapter 3 Software Configuration 33 3.2 Ethernet software configuration The PCM-9570/S ’ s on-board Ethernet interface supports all major network operating systems. To configure the medium type, to view the current configuration, or to run diagnostics, do the following: 1.
34 PCM-9570/S User's Manual.
Award BIOS Setup This chapter describes how to set BIOS configuration data. CHAPTER 4.
36 PCM-9570/S User's Manual 4.1 System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal.
Chapter 4 Award BIOS Setup 37 4.2 Award BIOS setup Award’s BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off.
38 PCM-9570/S User's Manual 4.2.2 Standard CMOS setup When you choose the STANDARD CMOS SETUP option from the INITIAL SETUP SCREEN menu , the screen shown below is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display.
Chapter 4 Award BIOS Setup 39 4.2.3 BIOS features setup By choosing the BIOS FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed.
40 PCM-9570/S User's Manual 4.2.4 Chipset features setup By choosing the CHIPSET FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9570/S.
Chapter 4 Award BIOS Setup 41 4.2.5 Power management setup By choosing the POWER MANAGEMENT SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9570/S.
42 PCM-9570/S User's Manual 4.2.6 PnP/PCI configuration By choosing the PnP/PCI CONFIGURATION option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9570/S.
Chapter 4 Award BIOS Setup 43 4.2.7 Integrated peripherals By choosing the INTEGRATED PERIPHERALS option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-9570/S.
44 PCM-9570/S User's Manual 4.2.8 Load BIOS defaults LOAD BIOS DEFAULTS loads the default system values directly from ROM. If the stored record created by the Setup program becomes corrupted (and therefore unusable), these defaults will load automatically when you turn the PCM-9570/S on.
Chapter 4 Award BIOS Setup 45 4.2.9 Change password To change the password, choose the PASSWORD SETTING option form the Setup main menu and press <Enter>. 1. If the CMOS is bad or this option has never been used, a default password is stored in the ROM.
46 PCM-9570/S User's Manual 4.2.10 Auto detect hard disk The IDE HDD AUTO DETECTION utility can automatically detect the IDE hard disk installed in your system. You can use it to self-detect and/or correct the hard disk type configuration. Figure 4-9: IDE HDD auto detection screen 4.
PCI SVGA Setup • Introduction • Installation of SVGA driver for - Windows 95 - Windows 98 - Windows NT CHAPTER 5.
48 PCM-9570/S User's Manual 5.1 Introduction The PCM-9570/S has an on-board PCI flat panel/VGA interface. The specifications and features are described as follows: 5.1.1 Chipset The PCA-9570/S uses a Trident 9525DVD chipset for its PCI/SVGA controller.
Chapter 5 PCI SVGA Setup 49 5.1.4 Dual/simultaneous display The PCM-9570/S uses a Trident Cyber 9525DVD LCD controller that is capable of providing multiple views and simultaneous display with mixed video and graphics on a flat panel and CRT. To set up dual display under Windows 98, follow these steps: 1.
50 PCM-9570/S User's Manual 5.2 Installation of SVGA driver Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your PCM-9570/S. Impor tant: The follo wing windows illustrations are examples only .
Chapter 5 PCI SVGA Setup 51 a. Select "S tart" , "Settings" , "Control Panel" , "Display" , "Settings". b. Press "Advanced Properties". a. Choose the "Adapter" label. b. Press the "Change.
52 PCM-9570/S User's Manual a. Insert the disc into the CD-ROM drive. b. Type "D:Biscuit9570 VGA.100Win9X". 5. c. Press "OK". D:Biscuit9570VGA.100Win9X a. Click the "Next" button. 7. "Trident Cyber9525DVD PCI/AGP" appears in the Adapter.
Chapter 5 PCI SVGA Setup 53 9. Pr e ss " Y e s" t o r eboot . a. a. R epeat St ep 1 on t he pr evi ous page of t hi s m anual . l abel appear s i n "Di spl ay" . b. A dj ust r esol ut i on and col or . The "Trident" 10. Click "Advanced" for further adjustment.
54 PCM-9570/S User's Manual 5.2.2 Installation for Windows NT a. Select "Start", "Settings", "Control Panel". b. Double click the "Display" icon. a. Choose the "Settings" label. b. Press the "Display Type" button.
Chapter 5 PCI SVGA Setup 55 a. S el ect the hi ghl i ght ed ite m . b. P r ess t he "O K " but ton. a. P r ess "Y es" t o p r oceed. a. P r ess "O K " t o r eboot . 6. 7. 8. D:Biscuit9570VGA.100Winnt a . In s e rt th e d is c int o th e CD- RO M dr i ve .
56 PCM-9570/S User's Manual 9. a. Repeat Step 1 in this manual, to select the "Settings" label. b. Adjust resolution and color. c. Click "Test" to see the result.
Chapter 5 PCI SVGA Setup 57 5.3 Further information For further information about the PCI/SVGA installation in your PCM-9570/S, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Trident website: www.trid.
58 PCM-9570/S User's Manual.
SCSI Setup and Configurations The PCM-9570/S features an on-board SCSI interface. This chapter provides basic SCSI concepts and instructions for installing the software drivers with the SCSI driver disks/CD included in your package.
60 PCM-9570/S User's Manual 6.1 Introduction The PCM-9570/S is equipped with a Symbios SYM53C895 single-chip PCI-to-SCSI host adapter which provides a powerful Ultra2 multitasking interface between your computer ’ s PCI bus and SCSI devices (disk drives, CD-ROM drives, scanners, tape backups, removable media drives, etc.
Chapter 6 SCSI Setup and Configurations 61 6.2 Before you begin SDMS software requires an IBM PC/AT or compatible computer with an 80486 or higher microprocessor. An understanding of basic operating system commands is assumed. In addition, users should have a general knowledge of the SCSI standard.
62 PCM-9570/S User's Manual 6.4 Configuring the SCSI adapter Access the SCSI BIOS by holding down both the CTRL and C keys when you see the BIOS banner message listing the driver name and the attached devices. For example: Symbios Inc. SDMS (TM) V 4.
Chapter 6 SCSI Setup and Configurations 63 6.5 SCSI terminators To ensure reliable communication, the SCSI bus must be properly terminated. Termination is controlled by a set of electrical resistors, called terminators. Terminators must be placed (or enabled) at the two extreme ends of the SCSI bus.
64 PCM-9570/S User's Manual 6.6 SDMS drivers The SDMS device drivers translate an operating system I/O request into a SCSI request. Each Symbios SCSI device driver is operating system specific and is designed to work on standard Symbios chip implementations.
Chapter 6 SCSI Setup and Configurations 65 6.7 Utility user's guide and installation instructions The utility user's guide and installation instructions are provided in HTM format in the driver CD-ROM. Users can browse the instructions by using a java-aware browser such as Microsoft Internet Explorer v3.
66 PCM-9570/S User's Manual For Windows NT: • WINNT.HTM : Installation guide for device drivers for Windows NT • NEWASNT.HTM : Windows NT 4.0 guided installation for installing SYMC8XX or SYM_HI drivers • NTCONFG.HTM : Windows NT configuration utility (NTCONFIG) • NTDMI.
Chapter 6 SCSI Setup and Configurations 67 Other tools and utilities: • BIOS.HTM : User's guide for SCSI BIOS configuration utility • FLASH.HTM : SDMS host adapter Flash utility • FORMAT.HTM : SDMS SCSI low-level format utility • RAWRITE.
68 PCM-9570/S User's Manual.
7 CHAPTER PCI Bus Ethernet Interface This chapter provides information on Ethernet configuration. • Introduction • Installation of Ethernet driver for Windows 95/98/NT • Further information.
70 PCM-9570/S User's Manual 7.1 Introduction The PCM-9570/S is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T and 10Base-T compatible.
Chapter 7 PCI Bus Ethernet Interface 71 7.2.2 Installation for Windows 95/98 a. Select "Start", "Settings", "Control Panel". b. Double click "Network". a. Click "Add" and prepare to install network functions.
72 PCM-9570/S User's Manual Note 1: The correct file path f or Windo ws 98 is: Biscuit9570Lan.1008139bWin98 Note 2: In the file path, choose " 8139a " or " 8139b " according to the type of Ether net chip used. D:Biscuit9570Lan.
Chapter 7 PCI Bus Ethernet Interface 73 7.2.3 Installation for Windows NT a. Select "Start", "Settings", "Control Panel". b. Double click "Network". a. Choose the "Adapters" label. b. Click the "Add" button.
74 PCM-9570/S User's Manual 5. D:Biscuit9570Lan.1008139bWinnt a. Choose the "Realtek" item. b. Click "OK". 6. a. Make sure the configurations of relevant items are set correctly. b. Click "OK" to reboot. 7. END a. Insert the CD into the D: drive.
Chapter 7 PCI Bus Ethernet Interface 75 7.3 Further information Realtek website: www.realtek.com Advantech website: www.advantech.com www.advantech.com.
76 PCM-9570/S User's Manual.
Programming the Watchdog Timer The PCM-9570/S is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for whatever reason. This feature ensures system reliability in industrial standalone, or unmanned, environments.
78 PCM-9570/S User's Manual A.1 Programming the watchdog timer In order to program the watchdog timer, you must write a program which writes I/O port address 443 (hex). The output data is a value of time interval. The value range is from 01(hex) to 3E(hex), and the related time interval is 1 sec.
Appendix A Programming the Watchdog Timer 79 The following example shows how you might program the watchdog timer in BASIC: 10 REM Watchdog timer example program 20 OUT &H443, data REM Start and r.
80 PCM-9570/S User's Manual.
Installing PC/104 Modules This appendix gives instructions for installing PC/104 modules. APPENDIX B.
82 PCM-9570/S User's Manual B.1 Installing PC/104 modules The PCM-9570/S's PC/104 connectors give you the flexibility to attach PC/104 modules. Installing these modules on the PCM-9570/S is quick and simple. The following steps show how to mount the PC/104 modules: 1.
Appendix B Installing PC/104 Modules 83 Figure B-1: PC/104 module mounting diagram Figure B-2: PC/104 module dimensions (mm) (±0.1) PCM -9570/ S Female PC/104 Mounti ng Support Mal e PC/104 modul e 8. 9 95. 9 90. 8 5. 1 0 0 5. 1 90. 2 85. 1 5. 1 90. 8 82.
84 PCM-9570/S User's Manual T able B-1: PC/104 connectors (CN10) Pin Signal Signal Number Row A Row B Row C Row D 0— — 0 V 0 V 1 IOCHCHK* 0 V SBHE* MEMCS16* 2 SD7 RESETDRV LA23 IOCS16* 3 SD6 .
Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: • Ethernet 10/100Base-T connector • ATX power feature connector • SCSI connector • Keyboard.
86 PCM-9570/S User's Manual C.1 Ethernet 10/100Base-T connector (CN1) T able C-1: Ethernet 10Base-T connector (CN1) Pin Signal 1V CC 2 CRS LED 3 RCV+ 4 RCV- 5 BNC LED 6 GND 7 N/C 8 GND 9X M T + 10 XMT - C.
Appendix C Pin Assignments 87 C.3 SCSI Connector (CN4) T able C-3: SCSI connector (CN4) Pin Function Pin Function 1 SD12+ 35 SD12- 2 SD13+ 36 SD13- 3 SD14+ 37 SD14- 4 SD15+ 38 SD15- 5 SDP1+ 39 SDP1- 6.
88 PCM-9570/S User's Manual T able C-3: SCSI connector (CN4) [continued] Pin Function Pin Function 21 A TN+ 55 A TN- 22 GND 56 GND 23 BSY+ 5 7 BSY - 24 ACK+ 5 8 ACK- 25 RST+ 59 RST - 26 MSG+ 60 M.
Appendix C Pin Assignments 89 C.4 Keyboard and PS/2 mouse connector (CN5) T able C-4: Keyboard and mouse connector (CN5) Pin Signal 1 GND 2 MS VCC 3 MS DA T A 4 MS CLOCK 5 GND 6 KB VCC 7 KB DA T A 8 K.
90 PCM-9570/S User's Manual C.5 Main power connector (CN6) T able C-5: Main power connector (CN6) Pin Signal 1 +12 V 2 GND 3 GND 4 +5 V C.6 IR connector (CN8) T able C-6: IR connector (CN8) Pin S.
Appendix C Pin Assignments 91 C.7 Floppy drive connector (CN9) T able C-7: Floppy drive connector (CN9) Pin Signal Pin Signal 1 GND 2 DENSITY SELECT* 3 GND 4 N/C 5 GND 6 DRIVE TYPE 7 GND 8 INDEX* 9 GN.
92 PCM-9570/S User's Manual C.8 IDE hard drive connector (CN11) T able C-8: IDE hard drive connector (CN11) Pin Signal Pin Signal 1 IDE RESET* 2 GND 3D A T A 7 4D A T A 8 5D A T A 6 6D A T A 9 7D.
Appendix C Pin Assignments 93 C.9 Parallel port connector (CN12) T able C-9: Parallel port connector (CN12) Pin Signal Pin Signal 1 STROBE* 2 AUTOFD* 3 D0 4 ERR 5 D1 6 INIT* 7 D2 8 SLCTINI* 9 D3 10 GN.
94 PCM-9570/S User's Manual C.10 Backlight connector (CN13) T able C-10: Backlight connector (CN13) Pin Signal 1 +12 V 2 GND 3 Enable 4 Reserved 5 N.
Appendix C Pin Assignments 95 C.12 CRT display connector (CN15) Table C-12: CRT displ ay c onnect or (CN15) Pin Signal Pin Signal 1 RED 9 SIGNAL GND 2 DDC POWER 10 H-SYNC 3 GREEN 11 SIGNAL GND 4 SIGNA.
96 PCM-9570/S User's Manual C.13 24-bit LCD display connector (CN16) T able C-13: 24-bit LCD display connector (CN16) Pin Signal Pin Signal 1 VDD 5 V 2 VDD 5 V 3 GND 4 GND 5 VDD 3.
Appendix C Pin Assignments 97 C.14 Ext. LCD display connector (CN17) T able C-14: Ext. LCD display connector (CN17) Pin Signal Pin Signal 1 GND 2 GND 3 PD24 4 PD25 5 PD26 6 PD27 7 PD28 8 PD29 9 PD30 10 PD31 11 PD32 12 PD33 13 PD34 14 PD35 15 GND 16 GND 17 N/C 18 N/C 19 N/C 20 N/C Note 1: The model number of the CN17 connector is DF13A-20DP-1.
98 PCM-9570/S User's Manual Pi n N ame LCD 16- bit DSTN 18- bi t TFT 2 4-bi t TFT 3 6-bi t TFT PD0 LD 0 R5 R7 R o 5 PD1 LD 1 R4 R6 R o 4 PD2 LD 2 R3 R5 R o 3 PD3 LD 3 R2 R4 R o 2 PD4 LD 4 G5 G7 G.
Appendix C Pin Assignments 99 C.16 Front panel connector (CN18) T able C-16: Front panel connector (CN18) Pin Signal 1 HDD LED- (HARD DISK ACTIVE) 2 HDD LED+ (V CC ) 3 SPEAKER+ 4 SPEAKER- (GND) 5 GND 6 WA TCHDOG OUTPUT* 7 RESET SWITCH- (GND) 8 RESET SWITCH+ * low active C.
100 PCM-9570/S User's Manual C.18 COM port connector (CN20) T able C-18: COM port connector (CN20) Pin Signal Pin Signal 1 DCD1 2 DSR1 3 RX1 4 RTS1 5 TX1 6 CTS1 7 DTR1 8 RI1 9 GND 10 NC 11 DCD2 1.
Appendix C Pin Assignments 101 T able C-19: COM2 port for RS-232, RS-422 and RS-485 (CN20) Pin Signal RS-232 RS-422 RS-485 11 DCD2 TX- DA T A - 13 RxD2 TX + DA T A+ 15 TxD2 RX+ NC 17 DTR2 RX- NC 19 GN.
102 PCM-9570/S User's Manual C.19 CompactFlash card connector (CN21) T able C-20: CompactFlash card connector (CN21) Pin Signal Pin Signal 1 GND 2 D03 3 D04 4 D05 5 D06 6 D07 7 -CS0 8 A10 2 9 -A .
Appendix C Pin Assignments 103 C.20 PanelLink connector (CN22) T able C-21: PanelLink connector (CN22) Pin Signal Pin Signal 1 TX1+ 2 TX1- 3 TX1 GND 4 TXC GND 5 TXC+ 6 TXC- 7 DDC GND 8 VDD 5 V 9 VDD 5.
104 PCM-9570/S User's Manual C.21 Fan power connector (FAN1) T able C-22: Fan power connector (F AN1) Pin Signal 1N C 2 +12 V 3 GND 3 21.
System Assignments • System I/O ports • 1st MB memory map • DMA channel assignments • Interrupt assignments D APPENDIX.
106 PCM-9570/S User's Manual D.1 System I/O ports T able D-1: System I/O ports Addr . range (Hex) Device 000-01F DMA controller 020-021 Interrupt controller 1, master 022-023 Chipset address 040-.
Appendix D System Assignments 107 D.2 1st MB memory map T able D-2: 1st MB memory map Addr . range (Hex) Device F000h - FFFFh System ROM E000h - EFFFh Unused D000h - DFFFh SCSI ROM *CC00h - CFFFh Ethe.
108 PCM-9570/S User's Manual D.4 IRQ mapping chart T able D-4: IRQ mapping chart 0 Interval timer 1 Keyboard 2 Interrupt from Controller 2 3 COM2 4 COM1 5 COM4 6 FDD 7 LPT1 8R T C 9 Reserved 10 C.
Optional Extras APPENDIX E.
110 PCM-9570/S User's Manual E.1 PCM-10586-4 cable kit for PCM-9570/S The PCM-9570/S requires several cables for normal operation. You can make them yourself or purchase an optional cable kit assembly, which includes the following: .
Appendix E Optional Extras 111 E.2 USB cable Optional USB cable, part no: 1703100260 E.3 SCSI cables Optional Ultra Wide SCSI cable, 60 cm, part no: 1701680600 (HPP68M/HPP68M/HPP68M) Optional Ultra2 Wide SCSI cable, 120 cm, part no.
112 PCM-9570/S User's Manual.
Mechanical Drawings APPENDIX F.
114 PCM-9570/S User's Manual F.1 Component side Figure F-1: PCM-9570/S mechanical drawing - component side.
Appendix F Mechanical Drawings 115 F.2 Solder side Figure F-2: PCM-9570/S mechanical drawing - solder side.
116 PCM-9570/S User's Manual.
デバイスAdvantech 2006957006 5th Editionの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Advantech 2006957006 5th Editionをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAdvantech 2006957006 5th Editionの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Advantech 2006957006 5th Editionの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Advantech 2006957006 5th Editionで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Advantech 2006957006 5th Editionを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAdvantech 2006957006 5th Editionの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Advantech 2006957006 5th Editionに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAdvantech 2006957006 5th Editionデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。