AdvantechメーカーI/O Module 5000 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 72
ADAM-5000 Series I/O Module User's Manual Copyright Notice This doc ument i s copyrig hted, 19 97, by A dvantech C o., Lt d. All ri ghts ar e reserved. A dvantech C o., Ltd. , reserves the right t o make i mprovem ents to t he products described in this manual at any time without notice.
I/O Module Introduction ADAM-5000 Series I/O Module Us er’s Manual Table of Contents Chapter 1 Introduction ….……......... .........….......... ........…………. 1-1 Chapter 2 Analog Input Modules....... ...........….................….
I/O Module Introduction ADAM-5000 Series I/O Module Us er’s Manual Chapter 5 Serial Communication Module………..….............. ...... 5-1 5.1 AD AM-5090 4-port RS-232 Co mm unicati on Module........ ....... . 5- 2 Chapter 6 Analog I/O Mo dules C alibration.
Introduction 1.
Introduction 1- 2 ADAM 5000 IO modules User’ s Manu al This ma nu al introduces the d etail specifications fun ctions and applicatio n wiring of each ADAM -5000 I/O modul es.
Analog Input Modules 2.
Analog Input m odule 2- 2 ADAM 5000 IO modules User’ s Manu al Analog i nput modules use an A/D co nverter to con vert sensor v oltage, current, thermocouple or R TD signals into digital data. The digit al data is t hen translated into engineering units.
Chapter 2 2 - 3 Applicati on wiring Figure 2 - 2: RTD in puts.
Analog Input m odule 2- 4 ADAM 5000 IO modules User’ s Manu al T echnical specificatio ns of AD AM-5013 Analog in put channels three Input type Pt or Ni RTD Pt -100 to 100°C a=0.00385 Pt 0 to 100°C a=0.00 385 Pt 0 to 200°C a=0.00 385 Pt 0 to 600°C a=0.
Chapter 2 2 - 5 2.2 AD AM-5017 8-channel a nalog input mo dule The ADAM-5017 is a 16-bi t, 8-channel analog differential input m odule that provid es programmable input ranges on all channels. It accep ts millivolt inputs (±150mV , ±500mV), voltage inputs (±1V , ±5V and ±10V) and current input (±20 m A, requires 125 ohms resistor).
Analog Input m odule 2- 6 ADAM 5000 IO modules User’ s Manu al Applicati on wiring Figure2-4: Millivolt and volt inpu t Figure 2-5: Process curre nt input Note: T o keep m easurement accuracy plea se short the channels that are not in use.
Chapter 2 2 - 7 T e chnical specificatio ns of AD AM-5017 Analog Input Channels Eight differential Input Type mV, V, mA Input Range ± 150 mV, ± 500 mV, ± 1 V, ± 5 V, ± 10 V and ± 20 mA Isolation Voltage 3000 V DC Sampling Rate 10 samples/sec (total) Analog Input Signal Limit 15 V max.
Analog Input m odule 2- 8 ADAM 5000 IO modules User’ s Manu al 2.3 AD AM-5 017H 8-channel high s peed analog inp ut module The ADAM-5017H is a 12-bit plus sign bit, 8- channel analog differential input module that provide s programm ab le input ranges on each channel.
Chapter 2 2 - 9 Applicati on wiring Figure 2 - 7 : Millivolt an d volt input Figure 2 - 8 : Process current input.
Analog Input m odule 2- 10 ADAM 5000 IO modules Use r ’s Man ual Figure 2 - 9 : Locat ions of 12 5-ohm resist ors Note: T o maintain measuremen t accuracy please short channels not in use.
Chapter 2 2 - 11 T e chnical specification s of AD AM-5017H Analog Input Ch annels 8 differential ADC Resolution 12 bits, plus sign bit Type of ADC Successive approximation Isolation Voltage 3000 V DC.
Analog Input m odule 2- 12 ADAM 5000 IO modules Use r ’s Man ual Input Range With Overrangi ng Offset Error @ 25°C Offset Error @ - 10 to +70°C Gain Error @ 25°C Gain Error @ - 10 to +70°C Offset Drift Gain Drift Displa y Resolution 0 ~ 10 V 0 ~ 11 V ±1 LSB ±2 LSB ±1 LSB ±2 LSB 17 µV/°C 50 ppm/°C 2.
Chapter 2 2 - 13 2.4 AD AM-5 018 7-channel thermocouple in put module The ADAM-5018 is a 16-bi t, 7-channel thermocoupl e input module that features programmable input ranges on all channels. It accepts millivolt inputs (±1 5 mV , ±50 m V , ±100 mV , ±5 00 mV), voltage in puts (±1 V , ±2.
Analog Input m odule 2- 14 ADAM 5000 IO modules Use r ’s Man ual Applicati on wiring Figure 2-11: T herm ocouple input.
Chapter 2 2 - 15 T echnical specificatio ns of AD AM-5018 Analog Input Channels Seven differential Input Type mV, V, m A , Therm ocouple Input Range ± 15 mV, ± 50 mV, ± 100 mV, ± 500 m V, ± 1 V, ± 2.
Analog Output Module 3.
Analog Output Module 3- 2 ADAM 5000 IO modules User’ s Manu al 3.1 AD AM-5024 4-channel a nal og output mo dule The ADAM-5024 is a 4-ch annel analog output module. It receives its digital inpu t through the RS-485 interface of the ADAM-5510 system module f rom the host com puter .
Chapter 3 3- 3 Applicati on wiring Figure 3-2 : Analog output T echnical specificatio ns of AD AM-5024 Analog Output Channels Four Output Type V, mA Output Range 0-20mA, 4- 20m A , 0-10V Isolation Voltage 3000 Vdc Output Impedanc e 0.5 Ohms Accuracy ±0.
Digital Input/Output Modules 4.
Analog Input m odule 4- 2 ADAM 5000 IO modules User’ s Manu al 4.1 AD AM-5050 1 6-channel universal digi tal I/O mod ule The ADAM- 5050 featu res sixteen digital i nput/output channels . Each channel can b e independe ntly configure d to be an input or an output channel by the setting of its DIP sw itch.
Chapter 4 4- 3 Applicatio n wiring Figure 4 - 3 : Dry contact si gnal input (ADAM-5 050) Figure 4- 4: W et contact signal i nput (A DAM-5050) Figure 4-5: Digital output used with SSR (ADAM-5050 /5056).
Analog Input m odule 4- 4 ADAM 5000 IO modules User’ s Manu al T echnical specificatio ns of AD AM-5050 Points 16 Channel Setting Bitwise selectable by DIP swit ch Digital Input Dry C ontact Logic L.
Chapter 4 4- 5 4.2 AD AM-5051 series digital inpu t modul e 4.2.1 AD AM-5051 (D) 16 -channel d ig ital i nput m odul e The ADAM-5 051 provides sixteen digit al input cha nnels. The ADAM- 5510 can use the modul e’ s digital inputs to determine the state of l i mit or saf et y switches or to receive remote digital signals.
Analog Input m odule 4- 6 ADAM 5000 IO modules User’ s Manu al Figure 4-8: Contact closu re input (ADAM-505 1/5051D) T e chnical specificatio ns of AD AM-5051/5051D Points 16 Logic level 0: + 1 V max Digital input Logic level 1: + 3.5 to 30 V Pull u p current: 0.
Chapter 4 4- 7 4.2.2 AD AM-5051S 16-channel Isolated Di gital Input Module with LED The ADAM-5051S provides 16 isolated digital input channels for critical environments need individual channel isolating protection. Different from o t h e r ADAM-5 000 I/O modules, ADAM-5051S desi gned with 21 pins pl ug terminal.
Analog Input m odule 4- 8 ADAM 5000 IO modules User’ s Manu al T e chnical specificatio n of AD AM-5051S Point 16(4- channel/group ) Digital Input Lo gic Level 0: + 3 V m ax Logic Level 1: + 10 to 50 V Optical Is olation 2500 V DC Opto-isolator response time 25 µs Over-volt age Protection 70 V DC Power Consumption 0.
Chapter 4 4- 9 4.3 AD AM-5052 8-channel isolate d digital inpu t module The AD AM-5052 provides e ight fully i ndependent i solated c hannels. All have 5000 V RMS isolation to pr event ground loop effects and to pr e- vent damage from power surges on th e input lines.
Analog Input m odule 4- 10 ADAM 5000 IO modules Use r ’s Man ual T echnical specificatio ns of AD AM-5052 Points 8 Differential Digital input Logic level 0: + 1 V ma x Logic level 1: + 3. 5 to 30 V Isolation voltage: 5000 V RMS Resistance: 3 k Ω / 0.
Chapter 4 4- 11 4.4 AD AM-5055S 16 -channel Isolated Digital I/O Module with LED The ADAM-5056S provi des 8 isolated digital input and 8 is olated output channels for critical environments need individual channel isolati ng protection. Different from other ADAM-5000 I/O modules, ADAM-5051S d esig ne d wit h 21 pins plug terminal.
Analog Input m odule 4- 12 ADAM 5000 IO modules Use r ’s Man ual T echnical specificatio n of AD AM-5055S Points 16 Digita l Output 8 (8-channel/g roup) Open collector to 40 V 200 m A max load pe r .
Chapter 4 4- 13 4.5 AD AM-5056(D) seri es digital ou tput modul e w / L E D 4.5.1 AD AM-5056(D) 16-channel digital output module w / L E D The ADAM -5056 features si xteen digital o utput channels. T he digital outputs a re open-collector t ransistor switche s that you can cont rol from the ADAM-5 000 main unit.
Analog Input m odule 4- 14 ADAM 5000 IO modules Use r ’s Man ual T echnical specificatio ns of AD AM-5056 There are 16-point digi tal input a nd 16-point di gital output modul es in the ADAM-5000 series.
Chapter 4 4- 15 Applicati on wiring Figure 4-18: ADAM-5 056S module wirin g diagram Points 16(8-ch annel/group) Digita l Output O pen co llector to 40 V 200 mA max load pe r channel Optical Is olation 2500 V DC Opto-isolator response time 25 µs Supply Voltage 5 ~ 40 V DC Power consumption 0.
Analog Input m odule 4- 16 ADAM 5000 IO modules Use r ’s Man ual 4.5.3 AD AM-5056SO 16-channel Isolated Dig ital Output Module wi th LE D The ADAM-5 056SO pro vides 16 chan nels source type isolat ed digita l output f or critical environments need i ndividual chan nel isola ting protection.
Chapter 4 4- 17 T e chnical Specificatio n of AD AM-5 056SO Points 16(8-channel/g roup) Digita l Output Open collector to 40 V 200 m A max load per c hannel Optical Isol ation 2500 VDC Opto-i solator res pons e time 25 u s Supply Volt age 5 ~ 40 VDC Power consum ption 0.
Analog Input m odule 4- 18 ADAM 5000 IO modules Use r ’s Man ual 4.6 Relay Output Mod ules 4.6.1 AD AM-5060 relay output module The ADAM-5 060 relay output module is a low - cost altern ative to SSR modules. It provides 6 relay ch annels, two of Form A and four of Form C .
Chapter 4 4- 19 T e chnical specificatio ns of AD AM-5060 Points 6, two Form A and four Form C Contact ratin g A C: 125 V @ 0.6A; 25 0 V @ 0.3 A D C: 30 V @ 2 A; 110 V @ 0.6 A Breakdown v olt age 500 V AC (50/60 Hz) Relay on time (typi c al ) 3 ms Relay off ti me (typic al) 1 ms Total switching time 10 ms Insulation resistance 1000 M Ω min.
Analog Input m odule 4- 20 ADAM 5000 IO modules Use r ’s Man ual Applicati on wiring Figure 4-24: Rela y o utput T echnical specificatio ns of AD AM-5068 Points 8 Form A Contact Ra ting AC: 120 V @ 0.5 A DC: 30 V @ 1 A Breakdown V ol t age 500 V AC (50/60 Hz) Relay On T ime (typic al) 7 ms ec.
Chapter 4 4- 21 4.6.3 AD AM-5069 p ow e r relay output module The ADAM-5069 power relay output module p r ovides 8 relay channels of Form A. Switches can b e used to control the relays. Considered to user frien d ly, the ADAM-5069 also built with LED indicator for status reading easily.
Analog Input m odule 4- 22 ADAM 5000 IO modules Use r ’s Man ual 4.7 Counter/Frequency Module Overview Compatible AD AM-5000 Se ries Ma in Un its ADAM-5 080 is a 4-chan nel counter/fre quency module.
Chapter 4 4- 23 Alarm Setting Function While i n count er mode, y ou can set alarm status--Disable and Lat ch. If you want to disable it, you can sel ect Disabl e. If Latch status i s selected, it means the Alarm status will be "latched " whenever the alarm b eing triggered.
Analog Input m odule 4- 24 ADAM 5000 IO modules Use r ’s Man ual AD AM-5080 Applica tion Wiring Figure 4-27: Isolated Input Level Figure 4-28 : TTL Input Level.
Chapter 4 4- 25 AD AM-5080 Counter/Frequency Mode Selection Users can selec t Bi-direction, Up/Down Count er or Fre quency option as shown in Figure 44. Fi g u r e 4-29: Co u n t er / F re q u en c y M o d e Note: All four channels of ADAM-5080 will operate simultaneously i n the mode y ou have selected.
Analog Input m odule 4- 26 ADAM 5000 IO modules Use r ’s Man ual Figure 4 - 3 0 : Wiring for Up/ Down Counting Note : If you need only on e type of counting , connect C0A+ and C0A- for Up C ounting onl y; or co nnect C0B+ and C0B- for Down Counting on ly .
Chapter 4 4- 27 Features -- Frequenc y Mode If users want to select frequency mode, they can only utilize Up Counting typ e, and can only connect to C0A+ and C0A-.
Analog Input m odule 4- 28 ADAM 5000 IO modules Use r ’s Man ual Setting Initial Counter V alue In order to utilize the alarm function, users have to set a high-alarm limit value an d/or a low alarm limit value, and a in itial value to fulfill the requirements for a basic ala rm setting.
Chapter 4 4- 29 Getting the T otalizer V a lue If users want t o get the actual counter value, a form ula such as follows can facilitate an easy cal culation from the initial counter value, overfl ow .
Analog Input m odule 4- 30 ADAM 5000 IO modules Use r ’s Man ual Features--Digital Output Map ping If users want to use Digital Output function, ADAM utility is av a i l ab l e for setting sp ecific ally which modu le, chann el or s lot to receive the al arm s i g n a l s .
Chapter 4 4- 31 TTL/Isolated Inpu t Level According to your need, y ou can sel ect either TTL or Isolated Input Level by setting the configuration fo r the jumpers. Select the proper jumper settings for either TTL or Isolated Input according to Figure 53.
Analog Input m odule 4- 32 ADAM 5000 IO modules Use r ’s Man ual AD AM-5080 T e chnical Specification s Channel 4 Input Frequ ency 0.3 ~ 1000 Hz m ax. (Fre quency mode) 5000 Hz m ax. (Counte r mode) Input Level Isolated or TTL level Minim u m Puls e Width 500 µ sec.
S e r i a l Communication M o d u l e 5.
Serial Communication Module 5- 2 ADAM 5000 IO modules User’ s Manu al Overview Compatible AD AM-5000 Se ries Ma in Un its The ADAM-5090 is a 4-port RS-232 communication module to be im ple mented wit h the followi ng Advant ech ADAM-500 0 series main unit s: ADAM-551 0 ( w it h li b r a ry V er si o n V 1 .
Chapter 5 5- 3 Communication Backup Function W ith the ADAM-5090 you can implement dual co mmunication channels between your PC and the ADAM sy stem. Even when one of the two communication channel s is down, your system can still function through the alternative communication channel.
Serial Communication Module 5- 4 ADAM 5000 IO modules User’ s Manu al PIN Mapping PIN Name RJ-48 DB9 /DCD 1 1 RX 2 2 TX 3 3 /DTR 4 4 GND 5 5 /DSR 6 6 /RTS 7 7 /CTS 8 8 RI or +5V 9 9 GND 10 X T able .
Chapter 5 5- 5 I/O Slots an d I/O P o r ts Numbe ring The ADAM-5090 m odu le provides four RS-232 por ts for communication with target devices. Th e ports are numbered 1 thr ough 4. For programming, the definition of port number de pends on the slot number and port number .
Serial Communication Module 5- 6 ADAM 5000 IO modules User’ s Manu al LED Status of the AD AM-5090 Module There are two LEDs for each port on the front panel of the ADAM-5090 to display specific co mmunication status: a. Gr een LED (RX) : Data Re ceivin g Statu s; the LED indic ator is on wh en the port is receiving data.
Chapter 5 5- 7 port_set_spee d(1,1 15200L); //Enable Por t FIFO. He re we e nable 128 byte FIFO fo r port1. port_enable_fifo(1); //After these above settings are enabled, you can apply any other function lib rary to implement y our progra m.
Analog I/O Modules Calibration 6.
Analog I/O Modules Calibration 6- 2 ADAM 5000 IO modules User’ s Manu al Analog i nput/output m odules are ca librated when you receive them. However , calibration is so metimes requ ired.
Chapter 6 6- 3 Figure 6 - 2 : Zero ca libration 5 . Execute the Span Calibrati on command. This can be done wi th the ADAM utility so ftware. Figure 6 - 3 : Sp an calibration.
Analog I/O Modules Calibration 6- 4 ADAM 5000 IO modules User’ s Manu al 6 . CJC Cali bration (only for T/C input module) Figure 6 - 4 : Cold junction ca libration * Note: Zero calibration and span calibration must be completed be fo re CJC calibration.
Chapter 6 6- 5 Calibration v oltage (AD AM-5 017/5018) Module Input Range Code (Hex) Input Range Span Calibration Voltage 00h ±15 mV +15 mV 01h ±50 mV +50 mV 02h ±100 mV +100 m V 03h ±500 mV +500 m V 04h ±1 mV +1 V 05h ±2.
Analog I/O Modules Calibration 6- 6 ADAM 5000 IO modules User’ s Manu al Calibration v oltage (ADAM-5017H) Module Input Range Code (Hex) I nput Range Span Calibration Voltage 00h ±10 V +10 V 01h 0 ~ 10 V +10 V 02h ±5 V +5 V 03h 0 ~ 5 V +5 V 04h ±2.
Chapter 6 6- 7 6. 2 AD AM-5013 RTD Input Resistance Calibration 1 . Apply power to the module and let it warm up for abou t 30 minutes. 2 . Ma ke sure that the module is cor r ectly i nstalled an d is properly con- figured f or the input range you want to calibrate.
Analog I/O Modules Calibration 6- 8 ADAM 5000 IO modules User’ s Manu al Calibration resistances (ADAM-5013) Input Range Code (Hex) Input Range Span Calibration Resistance Zero Calibration Resistance 20 Pt, -100 to 100°C A = 0.00385 140 Ohms 60 Ohm s 21 Pt, 0 to 100°C A = 0.
Chapter 6 6- 9 6.3 Analog output module cali bration The output current of analo g output module s can be calibrated by using a low calibrati on value and a hi gh calibration val ue. The anal og output modules can be configured for one of two rang es: 0-20 mA and 4-20 mA.
Analog I/O Modules Calibration 6- 10 ADAM 5000 IO modules Use r ’s Man ual 4 . Issue the Analog Dat a Out com mand to the m odule with an output va lue of 4 m A.
デバイスAdvantech I/O Module 5000 Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Advantech I/O Module 5000 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAdvantech I/O Module 5000 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Advantech I/O Module 5000 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Advantech I/O Module 5000 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Advantech I/O Module 5000 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAdvantech I/O Module 5000 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Advantech I/O Module 5000 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAdvantech I/O Module 5000 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
