AdventメーカーCAM330の使用説明書/サービス説明書
ページ先へ移動 of 12
Model: CAM330 Wired License Plate / Rear Mounted Camera Inst allation Manual Features • Very Small Compact Camera • High Resolution, ¼ inch CMOS Color Camera • Waterproof Housing • 160 Degree.
2 T able of Content s Warnings ...................................................................................... 3 Product Description ..................................................................... 4 Packing List ..........................
3 W arnings The product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations.
4 Product Description This revolutionary camera design integr ates a backup camera with your vehicle’s rear license plate without c overing the license plate. The camera is easy to mount on your car, truck, or van with the br acket being hidden by your license plate.
5 Camera Inst allation License Plate Mounting Instructions 1. Remove the rear license plate. 2. Examine the vehicle to determine the best way to run the power wires to the reverse lights and the extension cable through the car. 3. The Camera can be mounted above or below the plate.
6 that is not covered by the warranty. If drilling a hole, perform th e following steps: a) Acquire a 5/8 inch drill bit, rust preventive, all of whic h can be purchased at a hardware store. b) Check behind the intended drilli ng location before dril ling to verify that no wires or mechanisms can interfere with or be damaged during drilli ng.
7 sure that the mounting screws will not hit any wires or equipment inside the vehicle. 2. Attach the surface mounting bracket to the vehicle with the hardware included.
8 Obtaining Reverse Power 1. Locate the reverse lamp in the tail light assembly. 2. Using the tap connector supplied, perform the following steps: a) Place the un-stripped positive lead from the tail lamp in the run channel, which runs completely through the connector.
9 Reverse/Normal Image Adjustment The camera comes standard with a reversed i mage, designed for mounting at the rear of the vehicle. If you need to change to a forward or normal image view, clip the blue jumper wi re loop on the wiring cable (labeled “Mirror Selection” below) to change the camera image to normal.
10 S pecifications 1. Voltage: DC12V 2. Current: 50 mA 3. Signal System: NTSC 4. Image Sensor: ¼” CMOS Sensor 5. Horizontal Resolution: 480 lines 6. Viewing Angle: 160 degrees 7. Minimum Illum ination: 0.7 Lux 8. Image Display: Selectable Nor mal/Reverse Image 9.
7.
8 © 2008 Audiovox Electr onics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788.
デバイスAdvent CAM330の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Advent CAM330をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAdvent CAM330の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Advent CAM330の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Advent CAM330で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Advent CAM330を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAdvent CAM330の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Advent CAM330に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAdvent CAM330デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。