CanonメーカーEOS 7D Mark IIの使用説明書/サービス説明書
ページ先へ移動 of 550
EOS 7D Mark II (G) INSTRUCTION MANUAL ENGLISH.
2 The EOS 7D Mark II (G) is a digital si ngle-lens reflex camera featuring a fine-detail CMOS sensor with approx . 20.2 effective megapixels, Dual DIGIC 6, approx. 100% viewfinder co verage, high-precision and high- speed 65-point AF (Cross-type AF point: Max.
3 Before starting, check that all the following items are included with your camera. If anything is missi ng, contact your dealer . * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instru ction Manu al and DVD/ CD-ROMs pro vided are listed on the next page.
4 The instruction manual consists of a booklet, leaflet, and PDF manuals in electronic form (provided on the DVD-ROM) . EOS Camera Instruction Manuals Disk DVD- ROM Contains the following PDF manuals:.
5 The camera can use the following cards regardless of capacity: If the card is new or was previously formatted by another camera or computer , format the card with this camera (p.67). CF (CompactFlash) cards * T ype I, UDMA mode 7-compatible. SD/SDHC*/SDXC* memory cards * UHS-I cards supported.
6 Quick Start Guide 1 Insert the battery (p.40) . T o charge the battery , see page 38. 2 Insert the card (p.41) . The camera-front side slot is for a CF card, and the camera-back side slot is for an SD card. * Shooting is possible with eith er a CF card or an SD card in the camera.
7 Quick Start Guide 6 While holding down the center of the Mode Dial, set it to < A > (Scene Intelligent Auto) (p.29) . All the necessary camera settings will be set automatically . 7 Focus on the subj ect (p.55) . Look through the viewfinder and aim the viewfinder center over the subject.
8 Icons in this Manual < 6 > : Indicates the Main Dial. < 5 > : Indicates the Quick Control Dial. < p > : Indicates the AF area selection lever . < 9 > : Indicates the Multi-controller . < 0 > : Indicates the Setting b utton.
9 For first-time DSLR users, Chap ters 1 and 2 explain the camera’s basic operations and shoo ting procedures. Chapters Introduction 2 Getting St arted 37 Basic Shooting 79 Setting the AF and Drive .
10 1 Introducti on 2 Item Check List.................... ..................... ......................... ............... 3 Instruction Ma nual and DVD/CD-ROMs .................. ..................... .... 4 Compatible Cards................ ...........
11 Contents 4 2 3 l Displaying the Grid. ........ ......................... ......................... ........ 74 Q Displaying the Electronic Level ......................... ..................... . 75 Setting the V iewfinder Information Dis play .....
Contents 12 6 5 B : Setting the White Balance ................... ......................... ....... 168 O Custom White Balance.................... ...................... .............. 1 69 P Setting t he Color T emperature ....................... ...
13 Contents 9 7 8 q Selecting the Metering Mode .............................. .................... 224 O Setting Exposure Compensat ion ............................ ................. 226 h Auto Exposure Brac keti ng (AEB) ............................
Contents 14 10 Aperture-pr iority AE ........................ ...................... ..................... 316 Manual Exposu re Shooting.................... ......................... ........... 320 Shooting S till Photo s .................... .......
15 Contents 13 12 11 14 Changing Image Playback Settings ............... ..................... .......... 394 Adjusting th e LCD Monitor Brightnes s ............... ........................ 394 Auto Rotatio n of V ertical Images ............. ........
Contents 16 16 15 Reference 467 B Button Functio ns ..................... ......................... .................. 468 Checking the Ba ttery Information .................... ......................... .... 470 Using a Househo ld Power Outlet ......
17 Power Charging the battery Î p.38 Battery check Î p.46 Battery information check Î p.470 Household power outlet Î p.474 Auto power off Î p.69 Card Formatting Î p.67 Recording function Î p.146 Select card Î p.148 Release shutter without card Î p.
18 Index to Features Image Quality Image-recording quality Î p.149 ISO speed Î p.154 Picture St yle Î p.160 White balance Î p.168 Auto Lighting Optimizer Î p.175 Noise reduc tion for high ISO speeds Î p.176 Noise reduction for long exposures Î p.
19 Index to Features Movie Shooting Movie shooting Î p. 313 AF method Î p.299 Movie Servo AF Î p.342 Movie Servo AF speed Î p.345 Movie Servo AF tracking sensitivity Î p.346 Movie recording quality Î p.330 Sound recording Î p.336 Time code Î p.
20 Camera Care This camera is a precision instrume nt. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater . If you accidentally drop th e camera into water , promptly consult the nearest Canon Service Center .
21 Handling Precautions If the camera has n ot been used for an e xtended period, test a ll its functions before using it. If you have not used the camera for some time or if there is an important sho.
22 Nomenclature < o > Drive mode selection/ AF operation/AF metho d selection button (p.141/86/299 ) < m > Flash exposure compensat ion/ISO sp eed setting button (p.257 /154) < U > LCD pa nel illumination button (p.60 ) < B > AF area selection/ Multi-function butto n (p.
23 Nomenclature < B > Info button (p.60, 75, 78, 204, 206, 288, 323, 354, 468) < p > AF area select ion lever (p.58) LCD pa nel (p.25-26) Eyecup (p.247 ) Viewfi nder eyepiece Power swit ch (p.45) < M > Menu butto n (p.64) T erminal cover < p > AF start bu tton (p.
Nomenclature 24 Dioptric adjustmen t knob (p.54) Sp ea ker (for so und) < b / X > Creative P hoto/ Comparativ e playback (T wo-image display) button (p.160, 2 33, 238/366) < c > Rating button (p.370, 37 1) < u > Index/Magnify/ Reduce button (p.
25 Nomenclature LCD Panel * The display will show only the settings currently applied. Shutter speed FE lock ( FEL ) Busy ( buSY ) Built-in flash recycling ( buSY ) Multi function lock warning ( L ) No card warning ( Card ) Error code ( Err ) Cleaning ima ge sensor ( CLn ) Logging funct ion ( LOG ) White balance (p.
Nomenclature 26 < J > CF card selection icon ISO speed (p .154) < i > ISO spee d (p.154) < A > Highlight t one prior ity (p.180) Exposure level indicator (Setting value) Exposure compensa tion amou nt (p.226) AEB range (p.2 27) Flash expo sure com pensation amount (p.
27 Nomenclature Viewfinder Information * The display will show only the settings currently applied. Electronic level (p.76) S pot meterin g circle (p.224) Grid (p.74) White bal ance (p.168) Shooting mode Drive mode (p.141) AF operatio n (p.86) Metering mode (p.
Nomenclature 28 < z > Battery check (p.46) < A > AE lock (p.229) AEB in-progress (p.227) < D > Flash-re ady (p.254, 25 9) Improper FE lock warning < d > FE lock (p.259) FEB in-progress (p.2 69) < e > High-speed sy nc (p.269) < y > F lash exposure compensation (p.
29 Nomenclature Mode Dial Y ou can set the shooting mode. Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). A : Scene Intelligent Auto (p.80) F : Bulb (p.230) a : Manual exposure ( p.222) f : Aperture-priority AE (p.
Nomenclature 30 EF-S18-135mm f/3.5-5.6 IS STM Lens Focusing ring (p.1 40, 308) Focus mode switch (p.50) Zoom position ind ex Contacts (p.21) Lens mount i ndex (p.50) Image St abilizer switch (p.53 ) Filter thread (front of lens) Hood mount (p.5 2) Zoom ring (p.
31 Nomenclature EF-S15-85mm f/3.5-5.6 IS USM Le ns Focus mode switch (p.50) Zoom position ind ex Distance scale Contacts (p.21) Lens mount i ndex (p.50) Image S tabilizer switch (p.53) Focusing ring ( p.140, 308) Zoom ring (p. 51) Filter thread (front of lens) Hood mount ( p.
Nomenclature 32 Battery Charger LC-E6 Charger for Battery Pack LP-E6N/LP-E6 (p.38). Battery Charger LC-E6E Charger for Battery Pack LP-E6N/LP-E6 (p.38). Battery pack slot Charge lamp Power plug IMPORT ANT SAFETY INSTRUCTIONS-SA V E THESE INSTRUCTIONS.
33 Nomenclature Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle .
Nomenclature 34 When connecting the camera to a com puter , printer or Wireless F ile T ransmitter , use the provided inte rface cable or one from Canon (shown in the System Map on page 478) . When connecting the interface cable, also use the provided cable protector .
35 Nomenclature Using a Genuine Int erface Cable (sold separately) If you use a genu ine interfac e cable (sold separ ately , p. 478 ), ru n the cable thr ough the clamp before attachi ng the clamp to t he cable protector. Clamp Connecting interface cable without usi ng the cable protector may damage the digit al terminal.
36.
37 1 Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Minimizing Dust When changing lenses, do it quickl y in a place with minimal dust. When storing the camera with out a lens attached, be sure to attach the body cap to the camer a.
38 1 Remove the protective cover . Detach the protective cover provided with the battery . 2 Att ach the battery . As shown in the illustration, attach the battery securely to the charger . T o detach the battery , f ollow the above procedure in reverse.
39 Charging the Battery Upon purchase, the b attery is not fully charged . Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charge d battery will gradually drain and lose its capacity .
40 Load a fully-charged Battery Pack LP-E6N (or LP-E6) into the camer a. The camera’s viewfinder becomes bri ght when a battery is installed, and darkens when the battery is removed. 1 Open the cover . Slide the lever as shown by the arrows and open the cover .
41 The camera can use a CF card and an SD ca rd. Images can be recorded when at least one c ard is installed in the camera. If both types of card are inserted, you can select which card to record images to, or simultaneously record images on both cards (p.
Installing and Removing the Card 42 3 Close the cover . Close the cover and slide it in the direction shown by the arrows until it snaps shut. X When you set the power switch to < 1 > (p.45), the number of possible shots and the loaded card(s) will be displayed on the LCD panel.
43 Installing and Removing the Card 1 Open the cover . Set the power switch to < 2 >. Make sure the access lamp is off, then open the cover . If [ Recording... ] is displayed, close the cover . 2 Remove th e card. T o remove the CF card, push the eject button.
Installing and Removing the Card 44 When the access lamp is lit or blinking, it in dicates that images are being written to, read from, or erased from the card, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking.
45 If you turn on the power switch and the date/time/zone setting screen appears, see page 47 to set the date/time/zone. < 1 > : The camera turns on. < 2 > : The camera is turned off and does not operate. Set to this position when not using the camera.
Turning on the Power 46 When the power switch is set to < 1 >, the battery level will be indicated in one of six levels. A blinking battery icon ( b ) indicates that the battery will be exhausted soon.
47 When you turn on the power for the first time or if the date/time/zone are reset, the date/time/zone setting screen will appear. Follow the steps below , making sure to set the time zone first.
3 Setting the Date, Time, and Zone 48 4 Set the date and time. T urn the < 5 > dial to select the number . Press < 0 > so < r > is displayed. T urn the < 5 > dial to select the desired setting, then press < 0 > (Returns to < s >).
49 3 Selecting the Interface Language The date/time that were set will sta rt from when you press < 0 > in step 6. In step 3, the time displayed on the upper right of the screen is the time differe nce compared with Coordinated Universal T ime (UTC).
50 The camera is compatible with all Canon EF and EF-S lenses. The camera cannot be used wit h EF-M lenses. 1 Remove th e cap s. Remove the rear lens cap and the body cap by turning them as shown by the arrows. 2 Att ach the lens. Align the lens’s red or white mount index with the camera’s mount index of the same color .
51 Attaching and Detaching a Lens T urn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. T urning the zoom ring after achieving focus may throw off the focus. While pressing the lens release button, tu rn the lens as sh own by the arrow.
Attaching and Detaching a Lens 52 A lens hood can block unwanted light and prevent rain, snow , dust, etc. adhering to the front of the lens. Before storing the lens in a bag, etc., you can attach the hood in reverse. If the Lens and th e Lens Hood Have a Mount Ind ex 1 Align the red dots, then turn the hood as shown by the arrow .
53 When you use the IS lens’s built-in Image S tabilizer , camera shake is corrected to obtain a sharper s hot. The procedure explained her e is based on the EF-S18-135mm f/3.5-5.6 IS STM lens as an example. * IS stands for Image S tabilizer . 1 Set the IS switch to < 1 >.
54 T urn the dioptric ad justment knob. T urn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.247). T o obtain sharp images, hold the camera still to minimize camera shake.
55 Basic Operation The shutter button has two steps. Y ou can press t he shutter button halfway . Then you can further press the shutter button completely . Pressing Hal fway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture.
Basic Operation 56 T urn the dial whil e holding down the lock release butto n at the center of the dial. Use it to set the shooting mode. (1) Af ter pre ssing a button, turn the < 6 > dial. When you press a button such as < n > < o > < m >, the respective function remains selected for 6 sec.
57 Basic Operation (1) Af ter pre ssing a button, turn the < 5 > dial. When you press a button such as < n > < o > < m >, the respective function remains selected for 6 sec. ( 9 ). During this time, you can turn the < 5 > dial to change the setting.
Basic Operation 58 The < p > lever can be tilted to the right. Use it to select the AF area selection mode. Af ter pre ssing the < S > button, tilt the < p >. Pressing the < S > button will make the AF area selection mode and AF point selectable for 6 sec.
59 Basic Operation During movie shooting, the touch pad provides a quiet way to adjust the shutter speed, aperture, exposure compensation, ISO speed, sou nd recording level, and headphone volume (p.338). This function works when [ z 5: Silent Control ] is set to [ Enable h ].
Basic Operation 60 T urn on ( 9 ) or off the LCD panel illumination by pressing the < U > button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. After you press the < B > button a number of times, the shooting function settings will be displayed.
61 Y ou can directly select and set the shooting functions displayed on the LCD monitor . This is called Quick Control. 1 Press the < Q > button ( 7 ) . X The Quick Control screen will appear . 2 Set the desired functions. Use < 9 > to select a function.
Q Quick Control for Shooting Functions 62 Settable Function s on Quick Co ntrol Screen Shutter speed (p.218) AF operation (p.86) White balance correction / White balance bracketing (p.172/173) Shooting mode* (p.29) Highlight tone priority* (p.180) Auto Lighting Optimizer (p.
63 Q Quick Control for Shooting Functions Select a function and press < 0 >. The function setting screen will appear . T urn the < 6 > or < 5 > dial t o change some of the settings. There are also functions that are set by pressing the button.
64 Y ou can s et vari ous setti ngs with th e menus such as the i mage-record ing quality , dat e/time, etc. * Certain menu tabs and menu items are not displayed in the < A > mode.
65 3 Menu Operations 1 Display the menu screen. Press the < M > button to display the menu screen. 2 Select a tab. Each time you press the < Q > button, the main tab will switch.
3 Menu Operations 66 Example: When Multi Shot Noise Reduction is set Dimmed menu items cannot be set. The menu item is dimmed if another function setting is overriding it. Y ou can see the overriding function by selecting the dimmed menu item and pressing < 0 >.
67 If the card is new or was previously formatted by another camera or computer , format the card with this camera. When the card is formatted, all images and data on the card will be erased. Even protected images will be erase d, so make sure there is nothing you need to keep.
Before You Start 68 The card is new. The card was formatted b y a different camera or a compute r . The card is full with images or da ta. A card-related error is displayed (p.
69 Before You Start Y ou can prevent the beeper from sounding when focus is achieved or during self-timer operation. 1 Select [B eep]. Under the [ z 1 ] tab, select [ Beep ], then press < 0 >. 2 Select [D isable]. Select [ Disable ], then press < 0 >.
Before You Start 70 Y ou can set how long the image is displayed on the LCD monitor just after shooting. T o keep the image displayed, set [ Hold ]. T o not have the image displayed, set [ Off ]. 1 Select [Image review]. Under the [ z 1 ] tab, select [ Image review ], then press < 0 >.
71 Before You Start Shooting Function Settings AF Settings AF oper ation One-Shot AF Case 1 - 6 Case1/Parameter settings of all cases cleared AF area selection mode Single-point AF (Manual Selection) .
Before You Start 72 Image Recording Settings Camera Settings Image quality 73 Auto pow er off 1 min. Picture Style S tandard Be ep Enable Auto Lighting Optimizer S tandard Release shutter without card Enable Peripheral illu mination correction Enable/Correction data retained Image review time 2 sec.
73 Before You Start Live View Shooting Settings Movie Shooting Settings Live View shooting Enable Movi e Servo AF Enable AF method u +Tra cking AF method u +T racking Continuous AF Disab le Grid displ.
74 Y ou can d isplay a grid in the viewfin der to help you check the camera tilt or compose the shot. 1 Select [Viewfinder di splay]. Under the [ 5 2 ] tab, select [ Viewfinder display ], then press < 0 >. 2 Select [VF grid display]. 3 Select [Enabl e].
75 Y ou can display the electronic level on the LCD monitor and in the viewfinder to help you correct camera tilt. 1 Press the < B > button. Each time you press the < B > button, the screen display will change. Display the electronic level.
Q Displaying the Electronic Level 76 An electronic level can be displayed on the upper part of the viewfinder . Since this can be displayed while you shoot, you can correct the camera tilt while shooting. 1 Select [Viewfinder di splay]. Under the [ 5 2 ] tab, select [ Viewfinder display ], then press < 0 >.
77 The shooting function settings (Shoot ing mode, White balance, Drive mode, AF operation, Metering mode, Image quality: JPEG/R A W , Flicker detection) can be displayed in the viewfinder . By default, only Flicker detec tion is checkmarked [ X ]. 1 Select [Viewfi nder displa y].
78 When [ z Help ] is displayed at the bottom of the menu screen, the feature’s description (Help) can be displayed. The Help screen is displayed only while you hold down the < B > button. If the Help fills more than one screen, a scroll bar will ap pear on the right edge.
79 2 Basic Shooting This chapter explains how to use the Mode Dial’s < A > (Scene Intelligent Auto) mode for easy picture taking. In the < A > mode, all you do is point and shoot and the camera sets everything automatically (p.
80 < A > is a fully automatic m ode. The camera analyzes th e scene and sets the optimum settings automatically . It also adjusts focus automatically by detecting whether the subject is still or moving (p.8 3). 1 Set the Mode Dial to < A >.
81 A Fully Automatic Shooting (Scene Intelligent Auto) 4 T ake th e picture. Press the shutter button co mpletely to take the picture. X The captured image will be displayed for 2 sec. on the LCD monitor . After you finish shooting, push down the built-in flash with your fingers.
A Fully Automatic Shooting (Scene Intelligent Auto) 82 Pressing the shutter butto n halfway does not focu s on the subject. If the focus mode switch on the lens is set to < MF > ( manual focus), set it to < AF > (autofocus). The flash fired even thou gh it was daylight.
83 Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the < A > mode, pressing the shutter button halfway to focus on a still subject will lock the focus on that subject.
A Full Auto Techniques (Scene Intelligent Auto) 84 Y ou can shoot while viewing the im age on th e LCD monitor . This is called “Live View shooting”. For details, see page 285. 1 Set the Live View shooting/Movie shooting switch to < A >. 2 Display the Live View image on the LCD monito r .
85 3 Setting the AF and Drive Modes The AF points in the viewfinder are arranged to make AF shooting suitable for a wide variety of subjects and scenes. Y ou can also select the AF ope ration and drive mode that best match the shooti ng conditions and subject.
86 Y ou can select the AF opera tion characteristics to suit the shooting conditions or subject. In the < A > mode, “AI F ocus AF” is set automatically . 1 Set the lens’s focus mode switch to <AF>. 2 Set the < d > < s > < f > < a > < F > mode.
87 f : Selecting the AF Operation N Suited for still subjects. When you press the shutter button h alfway , the camera will focus only once. When focus is achieved, the AF p oint that achieved focus will be displayed, and the focus indicator < o > in the viewfinder will also light up.
f : Selecting the AF Operation N 88 This AF operati on is suited fo r moving subj ects when the focusing distance keeps changing. While you hold down the shut ter butto n halfway , the camera wi ll keep focusing o n the subject continuo usly . The exposure is set at the moment the picture is taken.
89 f : Selecting the AF Operation N When you press the shu tter button halfway and the camera is focusing with AF , the < i > icon will appear on the lower right of the viewfinder . In the One-Shot AF mode, the icon also appears if you press the shutter button halfway after focus is achieved.
90 The camera has 65 AF points for autofocusing. Y ou can select the AF area selection mode and AF point(s) suiting the scene or su bject. Depending on the lens attached to the camera , the number of usable AF points and AF point patterns will differ .
91 S Selecting the AF Area and AF Point N AF point exp ansion (Man ual selection, su rrounding po ints) The manually-selected AF point < S > and the surrounding AF points < w > are used to focus. Zone AF (Manual selection of zone) One of nine zones is u sed to focus.
S Selecting the AF Area and AF Point N 92 1 Press the < S > button. ( 9 ) 2 Operate the < p > or < B > button. Look through the viewfinder and operate the < p > or < B > button. Each time you tilt < p > to the right, the AF area selection mode changes.
93 S Selecting the AF Area and AF Point N Y ou can manually select the AF point or zone. 1 Press the < S > button. X The AF points will be displayed in the viewfinder . In AF point expansion modes, adjacent AF points will also be displayed. In the Zone AF mode, the selected zone will be displayed.
S Selecting the AF Area and AF Point N 94 Pressi ng the < S > button lights up the AF point s that are cross-type AF points for high-precision autofocus ing. The blinking AF points are horizontal-line or vertical-line sens itive. For details, see pages 99-103.
95 For pinpoint focusing over a narrower area than with single-point AF (manual selection). Select one AF point < > to focus. Effective for pinpoint focusing or focusing overlapping subjects such as an animal in a cage.
AF Area Selection Modes N 96 The manually-selected AF point < S > and surrounding AF points < w > are used to focus. The AF point exp ansion is larger than with AF point expansion (manual selection ), so the focusing is executed over a wider area.
97 AF Area Selection Modes N The AF area is divided into three focusing zones (left, center , and right) for focusing. Since the focusing area is larger than with Zone AF , it is superior in focusing on the subject.
AF Area Selection Modes N 98 When AI Servo AF mode is set with 65-point automatic selection AF , Large Zone AF (manual sel ection of zone), or Zone AF (manu al selection of zone), the active AF point < S > will keep switchi ng to track the subject.
99 The camera’s AF sensor has 65 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. With f/2.8 or larger maximum aperture lenses, high- precision AF is possible with the center AF point. Depending on th e lens attached to the camera, the number of usable AF points and AF pattern will differ .
100 Autofocusing with 65 points is possi ble. All the AF area selection modes are selectable. : Dual cross-type AF point. Subject tracking is superior and the focusing precision is higher than with other AF points. : Cross-type AF point. Subject tracking is superior and high- precision focusing is achieved.
101 Lenses and Usable AF Points Autofocusing with 65 points is possible. All the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and high- precision focusing is achieved. Autofocusing with 65 points is possible.
Lenses and Usable AF Points 102 Autofocusing with only 45 points is possible. (Not possible with all 65 AF points.) All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 65-point automat ic selection AF .
103 Lenses and Usable AF Points AF is possible with the center AF point and the adjacent AF points above, below , on the left, and on the right. Only the following AF area selection modes are selectable: Single-point AF (manual selection), Single-point S pot AF (manual selection) , and AF point expansion (manual selection ).
Lenses and Usable AF Points 104 Lens Group Des ignations EF-S24mm f/2.8 STM A EF85mm f/1.2 L USM A EF-S60mm f/2.8 Macro USM B EF85mm f/1.2L I I USM A EF-S10-18mm f/4.5-5.6 IS STM E EF85 mm f/1.8 USM A EF-S10-22mm f/3. 5-4.5 USM C EF100m m f/2 USM A EF-S15-85mm f/3.
105 Lenses and Usable AF Points EF300mm f/2.8L IS II USM A EF500mm f/4L IS USM B EF300mm f/2 .8L IS II USM + Extender E F1.4x B EF500mm f/4L IS USM + Extender EF1.4x B EF300mm f/2 .8L IS II USM + Extender E F2x B EF500mm f/4L IS USM + Extender EF2x G (f/8) EF300mm f/4 L USM B EF500mm f/4L IS II USM B EF300mm f/4 L USM + Extender E F1.
Lenses and Usable AF Points 106 EF24-105mm f/3.5- 5.6 IS STM B EF70-200 mm f/2.8L USM + Extender EF1.4x B* EF24-105mm f /4L IS USM B EF28-70mm f/2.8L U SM A EF70-200 mm f/2.8L USM + Extender EF2x B* EF28-70mm f/3.5- 4.5 E EF28-70mm f/3.5- 4.5 II E EF 70-200mm f/2.
107 Lenses and Usable AF Points EF100-30 0mm f/5. 6L B EF100-40 0mm f/4.5-5 .6L IS USM B EF100-40 0mm f/4.5-5 .6L IS USM + Extender E F1.4x G (f/8) EF100-40 0mm f/4.5-5 .6L IS II USM B EF100-40 0mm f/4.5-5 .6L IS II USM + Extender E F1.4x G (F8) EF200-40 0mm f/4L IS USM Extende r 1.
108 Y ou can easily fine-tune AI Servo AF to suit a particular subject or scene just by selecting an option from case 1 t o case 6. This feature is called the “AF Configuration T ool.” 1 Select the [ 2 1] tab. 2 Select a case. T urn the < 5 > dial to select a case icon, then press < 0 >.
109 3 Selecting AI Servo AF Characteristics N S tandard setting suited for any moving subject. Works with many subject s and scenes. Select [ Case 2 ] to [ Case 6 ] for the following: When an obstacle.
3 Selecting AI Servo AF Characteristics N 110 Once an AF point starts tracking the subject, this setting enables the camera to consecutively focus on subjects at different distances. If a new subject appears in front of the target subject, the camera will start focusing on the new subject.
111 3 Selecting AI Servo AF Characteristics N Even if the target subject moves dramatically up, down, left, or right, the AF point will switch automatically to focus-track the subject. Effective for shooting subjects that move dramatically up, down, left, or right.
3 Selecting AI Servo AF Characteristics N 112 Geared for tracking moving subjects whose speed can change drama tically and suddenly . Also, if th e target subject moves dramatically up, down, left or right and it is difficult to focus, the AF point switches automatically to track the subject.
113 3 Selecting AI Servo AF Characteristics N T racking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. 0 Default setting. Suitable for moving subjects in general.
3 Selecting AI Servo AF Characteristics N 114 Acceleration/deceleration tra cking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly , e tc. 0 Suited for subjects that move at a steady speed (minimal change in moving speed).
115 3 Selecting AI Servo AF Characteristics N AF point auto switching This sets the switching sensitivity of the AF points as they track the subject moving dramatically up, down, left, or right.
3 Selecting AI Servo AF Characteristics N 116 Y ou can manually adjust each case’s three parameters: 1. Tracking sensitivity , 2. Acceleration/decele ration tracking, and 3. AF point auto switching. 1 Select a case. T urn the < 5 > dial to select the icon of the case you want to adjust.
117 With the [ 2 2 ] to [ 2 5 ] menu tabs, you can set the AF functions to suit your shooting style or subject. Y ou can set the AF operation charac teristics and shutter-release timing for the first shot with AI Servo AF . : Equal prio rity Equal priority is given to focusing and shutter release.
3 Customizing AF Functions N 118 Y ou can set the AF operation cha rac teristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF . : Equal prio rity Equal priority is given to focusing and continuous shooting speed.
119 3 Customizing AF Functions N With the following USM and STM l enses equipped with an electronic focusing ring, you can set whether to use electronic manual focusing. : Enable after One-Shot AF After AF operates, if you keep pressing the shutter button halfway , you can adjust the focus manually .
3 Customizing AF Functions N 120 Enables or disables the AF-assist beam from the built-in flash or EOS- dedicated external Speedlite. ON: Enable The AF-assist beam is emitted when necessary . OFF: Disable The AF-assist beam is not emitted. Prevents the AF-assist beam from disturbing others.
121 3 Customizing AF Functions N Y ou can set the AF operation charac teristics and shutter-release timing for One-Shot AF . : Focus priority The picture will not be taken until focus is achieved. Effective when you want to achieve focus before capturing the shot.
3 Customizing AF Functions N 122 If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop searching. ON: Continue focu s search If focus cannot be achieved with autofocus, the lens is driven to search for the correct focus.
123 3 Customizing AF Functions N Y ou can change the number of ma nually selectable AF points. If 65- point automatic selection AF is set, the Area AF frame (entire AF ar ea) will be used for AF regardless of the setting below . : 65 points All 65 AF points will be manually selectable.
3 Customizing AF Functions N 124 Y ou can limit the selectable AF area selection mode s to suit your shooting preferences. Select the desired selection mode and press < 0 > to append a checkmark < X >. Then select [ OK ] to register the setting.
125 3 Customizing AF Functions N Y ou can set the method for changing the AF area selection mode. p / : S 9 M-Fn button After you press the < S > button, operating the < p > or < B > button changes the AF area selection mode.
3 Customizing AF Functions N 126 : Sep arate AF pts: Area+pt The AF area selection mode and AF point (or zone) can be set separately for each camera orientatio n (1. Horizontal, 2. V ertical with the camera grip at the top, 3. V ertical with the camera grip at the bottom).
127 3 Customizing AF Functions N Y ou can set the AI Servo AF’s starting AF point for when the AF area selection mode is set to Auto selection: 65 pt AF .
3 Customizing AF Functions N 128 EOS iTR* AF executes autofocus by recognizin g faces and subject colors. EOS iTR AF works when the AF area selectio n mode is set to Zone AF (manual selection of zone), Lar ge Zone AF (manual selection of zone), or 65-point automatic selection AF .
129 3 Customizing AF Functions N During manual AF point selection, the selection can either stop at the outer edge or it can cycle around to the opposite side.
3 Customizing AF Functions N 130 Y ou can set whether or no t to display the AF point(s) in the following cases: 1. When selecting the AF point(s), 2. When the camera is ready to shoot (before AF operation), 3. During AF oper ation, and 4. When focus is achieved.
131 3 Customizing AF Functions N Y ou can set whether the AF points in the viewfinder are to light up in red when focus is achieved. AUTO: Auto The AF points automatically light up in red under low light. ON: Enable The AF points light up in red regardless of the ambient light level.
3 Customizing AF Functions N 132 The AF status icon indicating AF operation can be displayed in the viewfinder ’s field of view or outside the field of view . : Show in field of view The AF status icon < i > is displayed in the lower right of the viewfinder ’s field of view .
133 Fine adjustment of the AF’s point of focus is possible for viewfinder shooting. This is called “AF Mi croadju stment”. Before making the adjustment, read “Cautions for AF Microadjustment ” on page 138. Normally , this adjustment is not required.
3 Fine Adjustment of AF’s Point of Focus N 134 4 Make the adjustment. Set the adjustment amount. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to the rear of the standard point of focus.
135 3 Fine Adjustment of AF’s Point of Focus N Y ou can make the adjust ment for each lens and register the adjustment in the camera. Y ou ca n register the adjustment f or up to 40 lenses. When you autofocus with a lens whos e adjustment is register ed, the point of focus will always be shifted by the adjustment amount .
3 Fine Adjustment of AF’s Point of Focus N 136 Entering the Serial Number Select the digit to be entered, then press < 0 > so that < r > appe ars.
137 3 Fine Adjustment of AF’s Point of Focus N 4 Make the adjustment. For a zoom lens, select the wide-angle (W) or telephoto (T ) end. Pressing < 0 > will turn off the purple frame and make the adjustm ent possible. Set the adjustment amount, then press < 0 >.
3 Fine Adjustment of AF’s Point of Focus N 138 When [ Clear all ] appears at the bottom of the screen, pr essing the < L > button will clear all the adjustments made for [ All by same amount ] and [ Adjust by lens ].
139 Autofocus can fail to achieve focus (viewfinder ’s focus indicator < o > blinks) with certain subjec ts such as the following: Subjects Diffi cult to Focus Subjects with very low contrast (Example: Blue skies, solid-color flat surfaces, etc.
When Autofocus Fails 140 1 Set the lens’s focus mode switch to <MF>. X < 4 L > will be displayed on the LCD panel. 2 Focus on the su bject.
141 Single and continuous drive modes ar e provided. Y ou can se lect the drive mode suiting the scene or subject. 1 Press the < o > button. ( 9 ) 2 Select the dr ive mode. While looking at the LCD panel or viewfinder , turn the < 5 > dial.
o Selecting the Drive Mode 142 Q : 10-sec. self-time r/remote control k : 2-sec. self-timer/remote control For self-timer shooting, see page 143. For remote control shooting, see page 248. By setting [ 8 2: Continuous shooting speed ] (p.439), you can manual ly set the conti nuous shooting speed.
143 Use the self-timer when you want to be in the picture. 1 Press the < o > button. ( 9 ) 2 Select the self-timer . While looking at the LCD panel or viewfinder , turn the < 5 > dial. Q : 10- sec. self-timer k : 2- sec. self-timer 3 T ake th e picture.
144.
145 4 Image Settings This chapter explains imag e-related function settings: Image-recording quality , ISO speed, Picture S tyle, white balance, Auto Lighting Optimizer , noise reduction, highlight tone priori ty , lens abe rration correction, anti- flicker shooting, and other functions.
146 If either a CF card or SD card is already inserted in the camera, you can start recording captured images. When only one card is inserted, you do not hav e to follow the proced ures described on pages 146-148.
147 3 Selecting the Card for Recording and Playback St anda rd Images will be recorded to the card selected w ith [ Record/play ]. Auto switch ca rd Same as with the [ Stand ard ] setting, but if the card becomes full, the camera will automatically switch to the other card to record images.
3 Selecting the Card for Recording and Playback 148 If [ Record func. ] is set to [ Stand ar d ] or [ Auto switch card ], select the card for recording and playing images. If [ Record func. ] is set to [ Rec. separately ] or [ Rec. to multiple ], select the card for playing image s.
149 Y ou can select the pixel count and the image quality . There are eight JPEG image-recording q uality setti ngs: 73 , 83 , 74 , 84 , 7 a , 8 a , b , c . There are three RA W ima ge quality settings: 1 , 41 , 61 (p.152). 1 Select [Imag e quality]. Under the [ z 1 ] tab, select [ Image quality ], then press < 0 >.
3 Setting the Image-Recording Quality 150 Image-recor ding Qual ity Setting Examples 73 only 61 + 84 1 + 73 1 only If [–] is set for both RAW and JPEG , 73 will be set.
151 3 Setting the Image-Recording Quality Guide to Image-Recording Qua lity Settings (Approx.) *1: b is suitable for playing the images on a digi tal photo frame. *2: c is suitable for emailing the image or using it on a website. b and c will be in 7 (Fine) quality .
3 Setting the Image-Recording Quality 152 A RA W image is raw data output by the image sensor converted to digital data. It is recorded to the card as is, and you can select the quality as follows: 1 , 41 , or 61 . A 1 image can be processed with [ 3 1: RAW image processing ] (p.
153 3 Setting the Image-Recording Quality With Custom Controls, you can as sign the image-recording quality to the < B > button or depth-of-field preview button so you can switch to it momentarily .
154 Set the ISO speed (image sensor ’s sensitivity to light) to suit the ambient light level. With the < A > mode selected, the ISO speed will be set automatically (p.156). Regarding the ISO speed during movie shooting, see pages 317 and 321. 1 Press the < m > button.
155 i : Setting the ISO Speed N As H1 (equivalent to ISO 25600) and H2 (equivalent t o ISO 51200) are expanded ISO speed settings, noise (dots of light, band ing, etc.) and irregular colors will be more noticeable, and the resolution lowe r than usual.
i : Setting the ISO Speed N 156 If the ISO speed is set to “ A ” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway . As indicated below , the ISO speed will be set automatically to suit the shooting mode.
157 i : Setting the ISO Speed N Y ou can set the manually-settable ISO speed range (minimum and maximum limits). Y ou can set the minimum limit within ISO 100 to H1 (equivalent to ISO 25600), and the maximum limit within ISO 200 to H2 (equivalent to ISO 51200).
i : Setting the ISO Speed N 158 Y ou can set the automatic ISO speed range for Auto ISO w ithin ISO 100 - ISO 16000. Y ou can set the minimum limit within ISO 100 - ISO 12800, and the maximum limit within ISO 200 - ISO 16000. 1 Select [Auto IS O range].
159 i : Setting the ISO Speed N Y ou can set the minimum shutter speed so that the shutter speed set automatically will not be too slow when Auto ISO is set. This is convenient in the < d > and < f > modes when you use a wide- angle lens to shoot a moving subjec t or when you use a telephoto lens.
160 By selecting a Picture Style, y ou can obtain image characteristics matching your photographic ex pression or the subject. The Picture S tyle is set automatically to [ D ] (Auto) in the < A > mode. 1 Press the < b > button. 2 Select [ A ].
161 A Selecting a Picture Style N D Auto The color tone will be adjusted autom atically to suit the scene. The colors will look vivid, especially for blue skies, greenery and sunsets, and in nature, outdoor and sunset scenes. P St andard The image looks vivid, sharp, and crisp .
A Selecting a Picture Style N 162 V Monochrome Creates black-and-white images. W User Def. 1-3 Y ou can register a b asic style such as [ Portrait ], [ Landsc ape ], a Picture S tyle file, etc., and adjust it as desired (p.166). Any Use r Defined Picture S tyle that is not se t will have the same settings as the [ Stan d ar d ] Picture S tyle.
163 Y ou can customize a Picture Style by adjusting individual parameters such as [ Sharpness ] and [ Contrast ]. T o see the r esulting effects, take test shots. T o customize [ Monochrome ], see page 165. 1 Press the < b > button. 2 Select [ A ].
A Customizing a Picture Style N 164 5 Set the parameter . Adjust the parameter as desired, then press < 0 >. Press the < M > button to save th e adjusted parameters. The Picture S tyle selection screen will reappear . X Any parameter settings different from the default will be displayed in blue.
165 A Customizing a Picture Style N For Monochrome, you can also set [ Filter effect ] and [ T oning effect ] in addition to [ Sharpness ] and [ Contrast ] explained on the pre ceding pages. k Filter effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more.
166 Y ou can select a base Picture Style such as [ Portrait ] or [ Landscape ], adjust its parameters as des ired and register it under [ U ser Def. 1 ], [ User Def. 2 ], or [ User Def. 3 ]. Y ou can create multiple Picture Styles with dif ferent settings for parameters such as sharpness and contrast.
167 A Registering a Picture Style N 6 Select a parameter . Select a parameter such as [ Sharpness ], then press < 0 >. 7 Set the parameter . Adjust the parameter as desired, then press < 0 >. For details, see “Customizing a Picture S tyle” (p.
168 White balance (WB) is for making the white areas look white. Normally , the < Q > (Auto) setting will obtain the correct white balance. If natural- looking colors cannot be obtained with < Q >, you can select the white balance to match the light source or set it manually by shooting a white object.
169 B : Setting the White Balance N T o the human eye, a white object looks white regardless of the type of lighting. With a digital camera, the color temperature is adjusted with software to make the white areas look white. This adjustment serves as the basis for the color correction.
B : Setting the White Balance N 170 3 Import the white balanc e data. T urn the < 5 > dial to select the image captured in step 1, then press < 0 >. X On the dialog screen that appears, select [ OK ] and the data will be imported. Press the < M > button to exit the menu.
171 B : Setting the White Balance N Y ou can set the white balance’s color temperature numerically . This is for advanced users. 1 Select [W hite bala nce]. Under the [ z 2 ] tab, select [ White balance ], then press < 0 >. 2 Set the color temperature.
172 Y ou can correct the white balance that is set. This adju stment will have the same effect as using a commerc ially-available color temperature conversion filter or color compens ating filter.
173 u White Balance Correction N With just one shot, three images with different color tones can be recorded simultaneously . Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias.
u White Balance Correction N 174 During WB bracketing, the maxi mum burst for continuous shooting will be lower and the nu mber of possible shots will also de crease to one-third the normal number . Since three images are recorded for one shot, it takes longer to record the image to the card.
175 If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatical ly . This function is call ed Auto Lighting Optimizer . The default setting is [ Stan d a rd ]. With JPEG images, the correction is applied when the image is captured.
176 This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further red uced.
177 3 Setting Noise Reduction N Cautions for Setting Mult i Shot Noise Reduction If there is significant mi salignment in the image due to camera shake, the noise reduction eff ect may be minimal. If you are handholding the camera, keep it steady to prevent came ra shake.
3 Setting Noise Reduction N 178 Noise reduction is possible with images exp osed for 1 sec. or longer . 1 Select [Long exp. no ise reduction]. Under the [ z 3 ] tab, select [ Long exp. noise reduction ], then press < 0 >. 2 Set the desired setting.
179 3 Setting Noise Reduction N With [ Auto ] and [ Enable ], the noise reduct ion process after the picture is taken may t ake the same amount of ti me as that for the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1” or higher .
180 Y ou can reduce o verexposed highlight areas. 1 Select [Hig hlight tone priority]. Under the [ z 3 ] tab, select [ Highlight tone priority ], then press < 0 >. 2 Select [Enabl e]. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights.
181 Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characte ristic s. Color fri nging along su bject outlines is called chromatic aberrati on. And image distortion due to lens characteristics is called distortion.
3 Correction of Lens Peripheral Illumination and Aberrations 182 1 Select the setting. Check that [ Correction data available ] is displayed for the attached lens. Select [ Chromatic aberration ], then press < 0 >. Select [ Enable ], then press < 0 >.
183 3 Correction of Lens Peripheral Illumination and Aberrations The camera already contains data for lens peripheral illumination correction, chromatic aberration correc tion, and distortio n correction for approx.
3 Correction of Lens Peripheral Illumination and Aberrations 184 Cautions for Lens C orrection Peripheral illumination correction, chro matic aberration correction, and distortion correction cannot be appli ed to JPEG images alre ady taken.
185 If you shoot an image with a fast shutter speed under a light sour ce such as fluorescent light, the blinking of the light source causes flicker and the image may be vertically unevenly exposed. If continuous shooting is used under these conditions, uneven exposures or colors across the images may result.
3 Reducing Flicker N 186 If the subject is against a dark background or if there is a bri ght light in the image, flicker may not be detect ed. Under certain speci al types of lighting, the camera may not be able to reduce the eff ects of the flicker even while < G > is displayed.
187 The range of reproducible colors is called “color space”. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. The color space is set automatically to [ sRGB ] in the < A > mode.
188 Y ou can freely cr eate and select the folder where the captu red images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. 1 Select [Record fun c+card/folder sel.]. Under the [ 5 1 ] tab, select [ Record func+card/folder sel.
189 3 Creating and Selecting a Folder Select a folder on t he folder selection screen, then press < 0 >. X The folder where the captured images will be saved is selected.
190 The file name has four alphanumeric characters followed by a four-digit image number (p.193) and exten sion. The first four alphanumeric characters are se t upon factory shipment and unique to the camera. However, you can change them. With “User setting1”, you can change and reg ister the four characters as desired.
191 3 Changing the File Name Operate the < 5 > dial or < 9 > to move the and select the desired character . Then press < 0 > to enter it. 4 Exit the setting. After entering the correct number of characters, press the < M > bu tton, then select [ OK ].
3 Changing the File Name 192 The first character ca nnot be an underscore “_”. User setting2 When you select the “*** + image size” registered with User setting2 and take pictures, the image-recording qua lity character will be automatically appended as th e file name’s fou rth character from t he left.
193 The four-digit file number is like the frame number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999 and saved in one folder . Y ou can change how the file number is assigned. 1 Select [File numbering].
3 File Numbering Methods 194 Restart s the file numbering f rom 0001 each time the card is replaced or a new folder is created . When you replace the card, create a folder, or switch the target card (such as f 9 g ), the file numbering cont inues in sequence from 0001 for the images saved.
195 When you set the copyright information, it will be r ecorded to the image as Exif information. 1 Select [C opyright informa tion]. Under the [ 5 4 ] tab, select [ Copyright information ], then press < 0 >. 2 Select the option to be set. Select [ Enter author’s name ] or [ Enter copyright details ], then press < 0 >.
3 Setting Copyright Information N 196 When y ou select [ Display copyright info. ] in step 2, you can check the [ Author ] and [ Copyright ] informat ion that you entered. When you select [ Delete copyright information ] in step 2 on the preceding page, you can delete the [ Author ] and [ C opyright ] information.
197 5 GPS Settings This chapter explains the camera’s built-in GPS settings. The EOS 7D Mark II (G) can receive satellite navigation signals from GPS satellites (USA), GLONASS satellites (Russia), and the Quasi-Zenith Satellite System (QZSS) “Michibiki” (Japan).
198 Geotag information* 1 (latitude, longitude, elevation) and coordinated universal time* 2 can be appended to images. Using the digital compass (based on magnetic north), the shooting direction can be appended to images. These information can be used to show the shooting location and shooting direction on a map displayed on a computer .
199 GPS Features Shooting locations and the route traveled can be viewed on a map displayed on a computer , using the Map Utility (EOS software, p.538).
200 9 Countries an d Regions Permitti ng GPS Function Use Use of GPS function is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. T o avoid violating GPS f unction regulations, visit the Canon we bsite to check where use is allowed.
201 T o acquire GPS signals, take the camera outside where the sky is unobstructed. Face the top of the camera toward the sky while keeping your hands, etc., away from the camera top. When the signal acquisition conditions ar e good, it will take the camera approx.
Acquiring GPS Signals 202 If [ Enable ] is selected, < r > will still be displayed on the LCD panel even when you turn the camer a’s power switch to < 2 >. Also, since the camera will rece ive GPS signals at regular intervals, the battery will drain quickly and the number of possible shot s will decrease.
203 Acquiring GPS Signals 1 Select [Se t up]. Check that [ GPS ] is set to [ En able ]. Select [ Set up ], then press < 0 >. 2 Select [GPS information display ]. X Detailed GPS information is displayed. 3 T ake th e picture. Shots taken after GPS signal acquisition are geotagged.
Acquiring GPS Signals 204 Play back the images and press the < B > button to display the shooting information screen (p.357). T hen tilt < 9 > up or down to check the geotag information.
205 The interval (time) to upda te the geotag information can be set. Although updating the geotag information at shorter interva ls will make it more accurate, it will reduce the number of possible shots. 1 Select [Se t up]. Check that [ GPS ] is set to [ En able ].
206 Camera orientation information (the di rection the camera is fa cing) can be appended to the image. 1 Select [Set up]. Check that [ GPS ] is set to [ En able ]. Select [ Set up ], then press < 0 >. 2 Set [Digital compass] to [Enable]. Select [ Digital compass ], then pre ss < 0 >.
207 Using the Digital Compass While you are using the GPS function, if the [ Calibrate digital compass ] screen appears or if the direction indicated looks questionable, calibrate the digital compass as follows. The digital compass should be calibrated at the actual shooting location.
Using the Digital Compass 208 2 Move the camera. (1) Swing the camera to the le ft and right by at least 180°. (2) T ilt the camer a up and down by at least 180°. (3) T urn the camera by at least 180°. Be careful not to drop the camera. S teps (1), (2), and (3) can be performed in any order .
209 The time information obtained from GPS signals can be set in the camera. The margin of error is a pprox. ±1 sec. 1 Select [Se t up]. Check that [ GPS ] is set to [ En able ]. Select [ Set up ], then press < 0 >. 2 Select [Auto time setti ng].
210 When using the GPS logging function, the geotag information of the route the camera traveled is automatically recorded in the camera’s internal memory . Shooting locations and the route traveled can be viewed on a map displayed on a computer using the Map Utility (EOS software, p.
211 Logging the Route Traveled Geotag information for the route the camera traveled is recorded at the intervals set with [ Position update interval ] (p.205). The log data is saved in the camera’s internal memory by date. The table below shows how many days’ worth of data can be saved.
Logging the Route Traveled 212 The log data in the camera’s internal memory can be downloaded to a computer with EOS Utility (EOS software) or downloaded from a card after transferring the data to the card. When you use Map Utility (EOS so ftware, p.
213 Logging the Route Traveled Use the provided interface cable or one f rom Canon (p.478). When connecting the interfa ce cable, use t he provided cable protector (p.
214.
215 6 Advanced Operations In the < d > < s > < f > < a > < F > shooting modes, you can select the shutter speed, aperture, and other camera settings to change the exposure and obtain the desired result.
216 The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. Th is is called P rogram AE. *< d > stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to < d >. 2 Focus on the su bject.
217 d : Program AE If the “ 30" ” shutt er speed and the lower f/number blink, it indicates und erexposure. Increase the ISO speed or use fla sh.
218 In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure matching the brightness of the subject. This is ca lled shutter- priori ty AE. A faster shutter speed can freeze the acti on of a moving subject.
219 s : Shutter-Priority AE If the lower f/number blinks, it indicates underexposure. T urn the < 6 > dial to set a slower shutter speed until the aperture stop s blinking or set a higher ISO speed. If the higher f/number blinks, it in dicates overexposure.
220 In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is call ed aperture-priority AE. A higher f/number (smaller aperture hole) will make mo re of the foreground and background fall within acceptable focus.
221 f : Aperture-Priority AE The aperture opening (dia phragm) changes only at the moment when the picture is taken. Otherwise, the aperture remains fully open. Therefore, when you look at the scene through the viewfinder or on the LCD monitor , the depth of field will look narrow .
222 In this mode, you set both the shutter speed and aperture as desired. T o determine the exposure, refer to the exposure level indicator in th e viewfinder or use a commer cially- available exposure meter . This method is called manual exposure. * < a > stands for Manual.
223 a : Manual Exposure If the ISO speed is set to A (AUTO), you can set exposure compensation (p.226) as follows. •[ z 2: Expo.comp./AEB ] • Under [ 8 3: Custom Cont rols ], use [ s : Expo comp (hold b tn, turn ) ] (p.455) or [ p : Expo comp (hold down lever , turn ) ] (p.
224 Y ou can select one of four meth ods to measure the subject brightness. In the < A > mode, evaluative metering is set automatically . 1 Press the < n > button. ( 9 ) 2 Select the meterin g mode. While looking at the LCD panel or viewfinder , turn the < 6 > dial.
225 q Selecting the Metering Mode N r Spo t me t er in g This is for metering a specific spot of the subject or scene. S pot metering covers approx. 1.8% of the viewfinder area at the center . The spot metering circle will be displayed in the viewfinder.
226 Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set b y the camera. Exposure comp ensation can be set in the < d >, < s >, and < f > shooti ng modes.
227 By changing the shutter speed or aperture auto matically , the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracke ting. 1 Select [Ex po.comp./AEB].
h Auto Exposure Bracketing (AEB) N 228 During AEB, < A > in the viewfinder and < h > on the LCD panel will blink. If the drive mode is set to < u > or < B >, press the shutter button three times for each sho t.
229 Use AE loc k when the area of focus is to be dif ferent from the exposure metering are a or when you want to take multiple sh ots at the same ex posure setting. Pre ss the < A > button to lock the expos ure, then recomp ose and take th e shot.
230 In this mode, the shutter stays open as long as you hold down the shutter button completely , and closes when you let go of the shutter button. This is called bulb exposur e. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures.
231 F : Bulb Exposures Y ou can preset the bulb exposure’s exposure time. With the bulb timer , you need not hold down the shutter button during the bulb exposure. This reduces camera shake. The bulb timer can be set only in the < F > (Bulb) shoo ting mode.
F : Bulb Exposures 232 3 Set the desired expo sure time. Select the hour , minute, or second. Press < 0 > so < r > is displayed. Set the desired number , then press < 0 > (Returns to < s >). 4 Select [ OK]. X The set time will be displayed on the menu screen.
233 Highlight detail and shadow detail ar e retained for a high dynamic range of tones even with high-contrast scenes. HDR shooting is effective for landscape and still-life shots.
w : HDR (High Dynamic Range) Shooting N 234 Natural For images preserving a wide tonal range where the highlight and shadow details would otherwise be lost.
235 w : HDR (High Dynamic Range) Shooting N 5 Set [Continuous HDR]. Select either [ 1 shot only ] or [ Every shot ], then press < 0 >. With [ 1 shot only ], HDR shooting will be canceled automatically after the shooting ends. With [ Every shot ], HDR shooting continues until the setting in step 3 is set to [ Disable HDR ].
w : HDR (High Dynamic Range) Shooting N 236 8 T ake th e picture. HDR shooting is possible with viewfinder shooting and Live View shooting. X < w > will be displayed on the LCD panel. When you press the shu tter button completely , three consecutive images will be captured, and the HDR image will be recorded to the card.
237 w : HDR (High Dynamic Range) Shooting N When shooting HDR images with [ Auto Image Align ] set to [ Ena ble ], AF point display information (p.359) and Dust Delete Data (p.
238 Y ou can shoot two to nine e xposures to be merged into one imag e. If you shoot multiple-exposure images w ith Live View shooting (p.285), you can see how the single ex posures are being mer ged while shooting. 1 Press the < b > button. 2 Select Multip le exposure.
239 P Multiple Exposures N 4 Set [Multi-expos ctrl]. Select the desired multiple-exposure control method, then press < 0 >. Additive The exposure of each single exposure is added cumulatively . Based on the [ No. of exposures ], set a negative exposure compensation.
P Multiple Exposures N 240 6 Set the images to be saved. T o save all the single exposures and the merged multiple-exposure image, select [ All images ], then press < 0 >. T o save only the merged multiple- exposure image, select [ Result only ], then press < 0 >.
241 P Multiple Exposures N 9 Shoot subsequent exp osures. X When [ On:Func/Ctrl ] is set, the merged multiple-exposure image will be displayed. With Live View shooting, the multiple- exposure images merged so far will be displayed. By pressing the < B > button, you can display only the Live View image.
P Multiple Exposures N 242 With multiple exposures, the more exposures there are, the more noticeable th e noise, irregular colors, and banding will be. Also, as noise increases with higher I SO speeds, shooting at low ISO speeds is recommended. If [ Additive ] is set, the image processing after taking t he multiple exposures will take time.
243 P Multiple Exposures N Y ou can select an image recorded on th e card as the first single exposure. The original of the selected image will remain intact. Y ou can only select 1 images. Y ou cannot select 41 / 61 or JPEG images. 1 Select [Select image for multi.
P Multiple Exposures N 244 When [ On:Func/Ctr l ] is set and you have not finished shooting the set number of exposures, you can press the < x > button to view the merged multiple-exposure image so far . Y ou can check how it looks and the exposure.
245 P Multiple Exposures N Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Can I merge images recorded on the card? With [ Select image for multi.
246 Although using the self-timer or a remote switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). 1 Set [Mirror lo ckup] to [Enable].
247 Using the Eyepiece Cover Even if the drive mo de is set to cont inuous shooting, only one shot ca n be taken. Y ou can also use the self-timer or bulb timer with mirror lockup. If 30 seconds elapse af ter the mirror has locked up, it will go back down automatica lly .
248 Y ou can connect the Remote Switch RS- 80N3 (sold separately) or T imer Remote Controller TC -80N3 (sold separately) or any EOS accessory equipped with an N3-type terminal to the camera for shooting (p.478). T o operate the accessory , refer to its instruction manual.
249 R Remote Control Shooting 4 Select the self-timer . While looking at the LCD panel or through the viewfinder , turn the < 5 > dial to select < Q > or < k >. 5 Press the remote contro ller ’s transmit button. Point the remote controller toward the camera’s remote control sensor , and press the transmit button.
250 With the interval timer , you can set the shooting interval and the number of shots. The camera will repeat taking one shot with the set interval until the set number of shots are taken. 1 Select [Interval tim er]. Under the [ z 4 ] tab (the [ z 2 ] tab in < A >), select [ Interval timer ], then press < 0 >.
251 H Interval Timer Shooting 4 Select [O K]. X The interval timer settings will be displayed on the menu screen. X < H > will be displayed on the L CD panel. 5 T ake th e picture. X Shooting will start according to the interval timer settings. During interval timer shooting, < H > will blink.
H Interval Timer Shooting 252 If the le ns’s focus mode switch is se t to < AF >, t he came ra will no t shoot when focus is not achieved. Setting it t o < MF > and focus manually first is recommended. Live View sh ooting, movie shooting, bulb exposur es, or mirror lockup cannot be perf ormed with interval timer sh ooting.
253 7 Flash Photography This chapter explains how to shoot with the built-in flash and external S peedlites (EX-series, sold separately), how to set fl ash settings with the camera’s menu screen, and how to use the built-in flash for wireless flash shooting.
254 In the < d > < s > < f > < a > < F > modes, just press the < D > button to raise the built-in flash for flash photography . Before shooting, check that [ D ] is displayed in the viewfinder . After shooting, push the built-in flash back down with your fingers until it clicks into place.
255 D Using the Built-in Flash Effective Range of Bu ilt-in Flash (Approx. in meters/feet) ISO Speed EF-S18-135mm f/3. 5-5.6 IS STM EF-S15-85mm f/3- 5.6 IS USM Wide Angle: f/3.5 T elephoto: f/5.6 ISO 100 1-3.1 / 3.3-10.3 1-2.0 / 3.3-6.4 ISO 200 1-4.4 / 3.
D Using the Built-in Flash 256 Using the red-eye reduction lamp when taking a flash picture can reduce red eye. 1 Select [Red-eye red uc.]. Under the [ z 4 ] tab (the [ z 2 ] tab in < A >), select [ Red-eye reduc. ], then press < 0 >. 2 Select [Enabl e].
257 D Using the Built-in Flash Set flash exposure compensation if the flash exposure of the sub ject does not come out as desired. Y ou can set flash exposure compensation up to ±3 stops in 1/3-stop increments. 1 Press the < m > button. ( 9 ) 2 Set the expos ure compensation amount.
D Using the Built-in Flash 258 FE (flash exposure) lock obtains and locks the appropriate flash exposure for the desired part of the image. 1 Press the < D > button. X The built-in flash will be raised. Press the shutter button halfw ay and look through the viewfinder to check that the < D > icon is lit.
259 Flash photography with EX-series S peedl ite (sold separately) is as easy as with built-in flash. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a T ype-A camera that can use all the features of EX-series S peedlites.
D Using an External Speedlite 260 With an EZ/E/EG/ML/TL-series Speedlite set to A-TTL or TTL autoflash mode, the fl ash can be fired at full ou tput only . Set the camera’s shooting mode to < a > (manual exposure) or < f > (aperture-priority AE) and a djust the aperture setting before shooting.
261 D Using an External Speedlite If the camera is used with a flash unit or flash accessory dedicated to another camera brand, the camera may not operate properly and malfunction may resul t. Do not connect to the camera’s PC t erminal any flash unit with an output voltage of 250 V or more.
262 With the built-in flash or an EX-series, exter nal S peedlite compatible with flash function settings, you c an use the came ra’s menu screen to set flash functions and the exter nal S peedlite’s Custom Functions.
263 3 Setting the Flash N Y ou can set the flash sync speed for flash photography in the aperture-priority AE ( f ) mode. : Auto The flash sync speed is set automatically within a range of 1/250 sec. to 30 sec. to suit the scene’s brightness. With an external S peedlite, high-speed sy nc is also possible.
3 Setting the Flash N 264 When you use the built-in flash or an external, EX-series S peedlite compatible with flash function settings, you can press the < D > button to directly display the [ Built-in flash settings ] or [ External flash func. setting ] screen without first displaying the menu screen.
265 3 Setting the Flash N Flash mo de Normally , set this to [ E-T TL II ]. This enables autoexposure shooting with the built-in flash. T o set the flash output level manually , select [ Manual flash ]. Select [ 2 flash output ], then set the flash output level to within 1/1 - 1/128 (1/3-stop increments) before shooting.
3 Setting the Flash N 266 Shutter synchronization Normally , set this to [ 1st curtain ] so that the flash fires immediately after the exposure starts.
267 3 Setting the Flash N The screen display and setting options will vary dep ending on the external Speedlite model, current flash mod e, Speedlite’ s Custom Function setting s, etc. T o see which functions your S peedlit e (sold separately) provides, refer to the S peedlite’s instruction manual.
3 Setting the Flash N 268 Wireless functions / Flash rati o control Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the instruction manual of a S peedlite compatible with the wireless flash shooting.
269 3 Setting the Flash N Shutter synchronizat ion Normally , set this to [ First -curtain synchronization ] so tha t the flash fires immediately after the exposure starts. If [ Second-curtain synchronization ] is set, the flash will fire right before the shutter closes.
3 Setting the Flash N 270 When using second-curtain synchroniza t ion, set the shutter speed to 1/ 25 sec. or slower . If the shutter speed is 1/30 sec. or fa ster , first-curtai n synchronization will be applied automatically even if [ Second-curt ain synchronization ] is set.
271 3 Setting the Flash N For details on the external S peedlite’s Custom Functions, refer to the S peedlite’s (sold separately) instruction manual. 1 Select [Ex ternal fl ash C.Fn setting]. 2 Set the desired functions. Select the number , then press < 0 >.
272 The camera’s built-in flash can work as a master unit for Canon EX- series, external S peedlites havi ng a wireless slave feature. It can wirelessly trigger the S peedlite(s) to fire via optical tr ansmission. Be sure to read about wireless flas h photography (optical transmission) in the S peedlite’s instruction manual.
273 Using Wireless Flash N *1: If the S peedlite does not have a transmission channel set ting function, it operates regardless of the channel set on the camera. *2: In small rooms, the slave unit may work even if its wireless sensor does not face the camera.
Using Wireless Flash N 274 The table below shows the possible c onfigurations for wireless flash shooting. Choose the configurat ion suiting the subject, shooting conditions, the number of external Speedlites you use, etc. Wireless Fla sh Shooting Configura tions External S peedlite Built-in Flash Page Setting Quantity A:B Flash Ratio C Flash exp.
275 Using Wireless Flash N This shows the most basic setup for fully-automatic wire less flash shooting with one external S peedlite. Step s 1 to 4 and 6 apply to all wireless flash shooting. Therefore, th ese steps are omitted in other wireles s flash setups explained on the pages hereafter .
Using Wireless Flash N 276 4 Set [Flash mode] to [E-TTL II]. 5 Set [Wireless func.] to [ 0 ]. 6 Set [Channel]. Set the channel (1-4 ) to the same one as the slave unit. 7 Set [Firin g group] to [ 1 All]. The slave unit may be set to any firing group (A, B, or C).
277 Using Wireless Flash N This is fully automatic wireless flash shooting with one external S peedlite and the built-in flash. Y ou can change the flash ratio b etween the external S peedlite and built-in flash to adjust how the shadows look on the subject.
Using Wireless Flash N 278 Multiple S peedlite slave units c an be treated as one flash unit or separated into slave groups whose flash ratio can be set. The basic settings are shown below . By changing the [ Firing group ] setting, you can shoot with variou s wi reless flash setups with multiple S peedlites.
279 Using Wireless Flash N [ 1 (A:B)] Mul tiple slave uni ts in multiple group s Y ou can divide the slave units into groups A and B, and change the flash ratio to obtain the desired lighting effect. Refer to the S peedlite’s instruction manual and set one slave unit to firing group A and the other to firing group B.
Using Wireless Flash N 280 [ 1 (A:B C)] Multiple slave un its in multiple group s This is a variant of the [ 1 (A:B) ] setup. This setup has group C eliminating the background shadows created by groups A and B. Refer to the S peedlite’s instruction manual and set three slave units to firing group A, B, and C, respectively .
281 Using Wireless Flash N The built-in flash can also be added to wireless flash shooting explained on pages 278-280. The basic settings are shown below. By changing the [ Firing group ] setting, you can shoot with variou s wireless flash setups of multiple S peedlites complemented with the built-in flash.
Using Wireless Flash N 282 Flash exposure compen sation When [ Flash m ode ] is set to [ E-TTL II ], flash exposure compensation can be set. The flash exposure compensation settings that can be set (see below) vary de pending on the [ Wireless func. ] and [ Firing grou p ] settings.
283 Using Wireless Flash N When [ Flash mo de ] is set to [ Manual flash ], flash exposure can be set manually . The flash output settings that can be set ([ 1 flash output] , [ Group A output ], etc. ) vary depending on the [ Wireless f unc. ] setting (see below).
284.
285 8 Shooting with the LCD Monitor (Live View Shooting) Y ou can shoot while viewing the picture on the cam era’s LC D monitor . This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to < A >.
286 1 Set the Live View shooting/Movie shooting switch to < A >. 2 Display the Live View image. Press the < 0 > button. X The Live View image will appear on the LCD monitor . The Live View image will closely match the brightness level of the actual image you capture.
287 A Shooting with the LCD Monitor Set [ z 5: L ive View shoot. ] (the [ z 3 ] tab in < A >) to [ Enable ]. Number of Possible Shots with Live View Shooting The figures above are based on a fully-charged Battery Pack LP-E6N and CIP A (Camera & Imaging Prod ucts Association) testing standards.
A Shooting with the LCD Monitor 288 Each time you press the < B > button, the information display will change. Information Display ISO speed Possible shots Exposure level indicator Aperture Shut.
289 A Shooting with the LCD Monitor The histogram can be displayed when [ z 5: Expo. simulation: Enable ] (p.296) is set. Y ou can display the el ectronic l evel by pres sing the < B > button (p.
A Shooting with the LCD Monitor 290 In the < A > shooting mode, the camera detects the scene type and sets everything automatically to suit the scene. The detected scene type is indicated on the upper left of the screen. For cer tain scenes or shooting conditions, the icon displayed may not match the actual scene.
291 A Shooting with the LCD Monitor *5: Displayed with any of the lenses below: • EF-S18-55mm f/3.5-5.6 IS II • EF-S55-250mm f /4-5.6 IS II • EF300mm f/2.8L IS II USM • EF400mm f/2.8L IS II USM • EF500mm f/4L IS II USM • EF600mm f/4L IS II USM • Image Stabilizer lenses marketed in 2012 or later .
292 While the Live View image is displayed, if you press the < n >, < o >, < m >, or < b > button, the setting screen will appea r on the LCD monitor and you can turn the < 6 > or < 5 > dial to set the respective shooting fun ction.
293 Shooting Function Settings In the < d > < s > < f > < a > < F > modes, the AF method , Drive mode , Metering mode, Recording/playing back card and image quality , White balance, Picture S tyle, and Auto Lighting Optimizer can be set.
294 z 5 When the Live View shooting/Movie shooting switch is set to < A >, the Live View shooting menu options will appear under the [ z 5 ] and [ z 6 ] tabs (the [ z 3 ] tab in < A >). The settable functions on this menu screen apply only to Live View shooting.
295 3 Menu Function Settings Grid display With [ 3x3 l ] or [ 6x4 m ], you can display grid lines to help you level the camera vertically or horizontally . Also, with [ 3x3+diag n ], the grid is displayed together with diagonal lines to help you compose with better balance by al igning the intersections over the subject.
3 Menu Function Settings 296 Exposure simulation N Exposure simulation simulates and displays how the brightness of the actual image (exposure) will look. •E n a b l e ( g ) The displayed image brightness will be close to the actual brightness (exposure) of the re sulting image.
297 3 Menu Function Settings z 6 N Silent L V shooting N •M o d e 1 Y ou can suppress the camera noise w hen shooting. Continuous shooting is also possible. If < o > is set, you can shoot at a maximum continuous shooting speed of approx. 10.0 fps.
3 Menu Function Settings 298 Metering timer N Y ou can change how long th e exposure setting is displayed (AE lock time). Performing any of the following operatio ns will stop Live View shooting. T o start Live View shooting again, press the < 0 > button.
299 Y ou can select an AF method to suit the shooting co nditions and your subject. The following AF methods are provid ed: [ u (face)+T racking ] (p.300), [ FlexiZone - Multi ] (p.
Using AF to Focus (AF Method) 300 The camera detects and focuses on human faces. If a face moves, the AF point < p > also moves to track the face. 1 Display the Live View image. Press the < 0 > button. X The Live View image will appear on the LCD monitor .
301 Using AF to Focus (AF Method) 4 T ake th e picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.286). Focusing on a subject o ther than a human face Press < 9 > or < 0 >, and the AF fr ame < > will appear in the center .
Using AF to Focus (AF Method) 302 Y ou can focus over a wide area with up to 31 AF points (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection). 1 Display the Live View image. Press the < 0 > button.
303 Using AF to Focus (AF Method) 4 T ake th e picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.286). If the camera does not focus on the desired target subject with automatic AF point selection, select a zone or switch the AF method to [ FlexiZone - Single ] and refocus.
Using AF to Focus (AF Method) 304 The camera focuses with a single AF point. This is effective when you want to focus on a particular subject. 1 Display the Live View image. Press the < 0 > button. X The Live View image will appear on the LCD monitor .
305 Using AF to Focus (AF Method) AF Operation Even when focus is achieved, pre ssing the shutter butto n halfway will focus again. The image brightness may change during and after the AF operation. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult.
Using AF to Focus (AF Method) 306 Shooting Condition s that Make Focusing Diff icult Subject with low-contrast such as the blue sky , solid-color flat surfaces or when highlight or shadow details are lost. Subjects in low light. S tripes and other patterns where there is contrast only in the horizontal direction.
307 Using AF to Focus (AF Method) If you cannot achieve f ocus with AF , set the lens’s f ocus mode switch to < MF > and focus manually . If you shoot the subject at the perip hery and it is slightly out of focus, aim the center AF point or zone over t he subject to focus on, focus aga in, and then take th e picture.
308 Y ou can magnify the image and focus pr e cisely with MF (manual focus). 1 Set the lens’s focus mode switch to <MF> . T urn the lens’s focusing ring to focus roughly . 2 Display the magnifying frame. Press the < u > button. X The magnifying frame will appear .
309 MF: Focusing Manually 5 Focus manu ally . While looking at the magnified image, turn the lens’s focusing ring to focus. After achieving focus, press the < u > button to return to the normal view . 6 T ake th e picture. Check the exposure, then press the shutter button completely to take the picture (p.
310 General Live View Shooting Ca utions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable.
311 General Live View Shooting Ca utions Live View Image Under low- or bright-light conditions, the Live V iew image may not reflect the brightness of the captured image . Even if a low ISO speed is set, n oise may be noticeable in the displayed Live V iew image under low light.
312.
313 9 Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to < k >. For cards that can record movies, see page 5. If you handhold the camera and shoot movies, camer a shake can cause blurred mo vies.
314 When the shooting mode is set to < A >, < d >, or < F >, autoe xposure control will take effect to suit the scene’s current brightness. Exposure control will be the same for all the sh ooting modes. 1 Set the Mode Dial to < A >, < d >, or < F >.
315 k Shooting Movies When the shooting mode is < s >, you can manu ally set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to < s >.
k Shooting Movies 316 When the shooting mode is < f >, you can manually set the aperture for movie shooting. The ISO speed and shutter speed w ill be set automatically to suit the bri ghtness and obtain a standard exposure. 1 Set the Mode Dial to < f >.
317 k Shooting Movies ISO speed in the < A > mode In the < A > mode, the ISO speed will be set automatically within ISO 100 - ISO 16000. ISO Speed in the < d >, < s >, < f >, and < F > Mode The ISO speed will be set automatically within ISO 100 - ISO 16000.
k Shooting Movies 318 During movie shooting in the < A >, < d >, < s >, < f >, and < F > modes, this camera supports the function that turns on the Speedlite’ s LED light automatically in low-light conditions. For det ailed instructions, refer to the EX-series Speedlite’ s instruction manual.
319 k Shooting Movies During movie shooting in the < A > mode, an icon representing the scene detected by the camera will be displayed, and the shooting will be adapted to that scene. For certai n scenes or shooting conditions, the icon displayed may not match the actual scene.
k Shooting Movies 320 Y ou can manually set the shutter spe ed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to < a >. 2 Set the Live View shooting/Movie shooting switch to < k >.
321 k Shooting Movies 5 Focus and sho ot the movie. The procedure is the same as steps 3 and 4 for “Autoexposure Shooting” (p.314). ISO Speed in the < a > Mode With [ Auto ] ( A ), the ISO speed will be set automatically within ISO 100 - ISO 16000.
k Shooting Movies 322 Under [ ISO speed range ], if [ Maximum ] is set to [ H2 (51200) ] and you switch from still photo sh ooting to movie shooting, the maximum ISO speed for the manual ISO rang e during movie shooting will be H1 (equivalent to ISO 2560 0).
323 k Shooting Movies Each time you press the < B > button, the information display will change. * Applies to a single movie clip. Information Display Picture Style Card for recording/ playback .
k Shooting Movies 324 Y o u can display the electronic le vel by pressing the < B > button ( p.75). Note that if the AF method is set to [ u +T racking ] or the camera is connected to a TV set with an HDMI cable (p.385) , the electronic level cannot be disp layed.
325 k Shooting Movies Notes for Movie Shooting Movie-related settings are unde r the [ z 4 ] and [ z 5 ] tabs (p.342). In the < A > mode, they are under the [ z 2 ] and [ z 3 ] tabs. A movie file is recorded each time you shoot a movie. If the file size exceeds 4 GB, a new file will be created for every subsequent approx.
k Shooting Movies 326 The final image simulation shows the results of the current settings for Picture S tyle, white balance and other functions in the image so you can see what the captured image will look like. During movie shooting, the image disp layed will automatically show the effects of the settings listed below .
327 k Shooting Movies While shooting a movie, you can also take a still photo by pressing the shutter button completely . T aking Still Photos During Movie Shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx.
k Shooting Movies 328 If L 8 (59.94 fps) or 7 (50.00 fps) is set, or if [ z 5: V button function ] is set to [ / k ] or [ q / k ], you cannot ta ke still photos. S till photo shooting during movi e shooting will have approx. 99% coverage with L or w , and approx.
329 If you press the < n >, < o >, < m >, or < b > button while the image is displayed on the LCD monitor , the setting screen will appear on the LCD monitor and you can tur n the < 6 > or < 5 > dial to set the respective function.
3 Setting the Movie Recording Size 330 T o select the card for recording/ playing back, WB Shif t/Bracketing, or Picture S tyle parame ters, press the < B > button.
331 3 Setting the Movie Recording Size Y ou can select the movie’s size, frame rate, and compression method. Image Size L 1920x1080 Full High-Definition (Full HD) recording quality . The aspect ratio is 16:9. w 1280x720 High-Definition (HD) recording quality .
3 Setting the Movie Recording Size 332 Compression Method W ALL-I (For editing/I-only) Compresses one frame at a time for recording. Although the file size is larger than with IPB (S tandard) and IPB (Light), the movie is more suited for editing. X IPB (S tandard) Compresses multiple frames at a ti me efficiently for recording.
333 3 Setting the Movie Recording Size Records the movie at a frame rate of 24.00 fps. Applies to Full HD quality . If [ Enable ] is set, the movie is recorded in LBW or LBX . If you have set [ Movie rec. size ] and then set [ 24.00p ] to [ Enable ], set the [ Movie rec.
3 Setting the Movie Recording Size 334 In MOV Format (Approx.) In MP4 Format (Approx.) Total Movie Reco rding Time and File Size Per Minute Movie R ecordin g Quality T ot al Recording Time on Card File Size 4 GB 8 GB 16 GB L 87 X 8 min. 17 min. 34 min.
335 3 Setting the Movie Recording Size Movie Files Exceeding 4 GB Even if you shoot a movie exceedi ng 4 GB, you can keep shooting without interruption. During movie shooting, approx. 30 sec. befo re the movie reaches the 4 GB file size, the elapsed shoot ing time or time code displayed in the movie-shooting screen will start blinking.
336 Y ou can sh oot movies while r ecording sound with the built -in monaural mic rophone or an external ster eo microphone (commerc ially available). Y ou can also freely adjust the sound-recording l evel. Sound-recording sett ings are under [ z 4: Sound recording ] (the [ z 2 ] tab in < A >).
337 3 Setting the Sound Recording Using a micropho ne Normally , the built-in micro phone will record monaural sound. S tereo sound recording is also pos sible by connecting an externa l stereo microphone (commerciall y available) equipped with a miniature stereo plug ( φ 3.
338 Y ou can change the settings of the ISO sp eed, sound-recording level, etc., without making too much noise while shooting a movie. When [ z 5: Silent Control ] (the [ z 3 ] tab in < A >) is set to [ Enable h ], you can use the touch pad < h > on the inner ring of the Quick Control Dial.
339 The time code is a time reference recorded automatically to synchronize the movie during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Use [ z 5: Time code ] (the [ z 3 ] tab in < A >) to set the time code.
3 Setting the Time Code 340 Y ou can select what to disp lay on the movie shooting screen. Rec time : Indicates the elapsed time from the start of the movie shooting. Tim e c od e : Indicates the time code during movie shooting. Y ou can select what to display on the movie playback screen.
341 3 Setting the Time Code Tim e c od e The time code can be appended to a movie that is output via HDMI (p.350). Enable : Appends time code to HDMI output movie.
342 z 4 When the Live View shooting/Movie shooting switch is set to < k >, the movie shooting menu options will appear under the [ z 4 ] and [ z 5 ] tabs (the [ z 2 ] [ z 3 ] tabs in < A >). Movie Servo AF During movie shooting, the camera focuses on the subject continuously .
343 3 Menu Function Settings y If you wa nt to keep the focus at a specific point or you do not want the lens operation noise to be re corded, you can temporarily stop Movie Servo AF as follows. When you stop Movie Servo AF , the AF point wi ll turn gray .
3 Menu Function Settings 344 Grid display With [ 3x3 l ] or [ 6x4 m ], you can display grid lines to help you level the camera vertically or horizontally . Also, with [ 3x3+diag n ], the grid is displayed together with diagonal lines to help you compose with better balance by a ligning the intersections over the subject.
345 3 Menu Function Settings Movie Servo AF speed N Y ou can set the Movie Servo AF’s AF speed and its operation conditions. This function is settable when [ Movie Servo AF ] is set to [ Enable ] and [ AF method ] is set to [ FlexiZo ne - Single ].
3 Menu Function Settings 346 Movie Servo AF tracking sensitivity N Y ou can change the Movie Servo AF’s tracking sensitivity to one of five levels. This affects the responsiveness of AF tracking sensitivity when the AF point loses the subject, such as during panning or when an obstacle enters the AF points.
347 3 Menu Function Settings z 5 Silent L V shooting N This function applies to still photo shooting. For details, see page 297. Metering timer N Y ou can change how long the exposure setting is displayed (AE lock time). Tim e c od e Y ou can set the time code.
3 Menu Function Settings 348 V button fun ction Y ou can set the functions perfor m ed by pressing the shutter button halfway or completely during movie shooting.
349 3 Menu Function Settings [Mirroring] • The movie is displayed on the LCD monitor and via the HD MI output simultaneously . • The HDMI output movie does n ot show the shooting information, AF frame, and other details (output without an information overlay).
3 Menu Function Settings 350 5 3 HDMI frame rate For HDMI output, you can set the frame rate to [ Auto ], [ 59.94i ]/ [ 50.00i ], [ 59.94p ]/[ 50.00p ], or [ 23.98p ]. Set the frame rate that is compatible with the commercially-available external recording device you will use to record the movie via HDMI output.
351 General Movi e Shooting Cautio ns White < s > and Red < E > Internal T emperature Warning Icons If the camera’s internal temperatu re increases d ue to prolonged mov ie shooting or under a high am bient temperature, a white < s > or red < E > icon will appe ar .
352 General Movi e Shooting Cautio ns Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the scr een during movie shooting. It indicates ho w much data has not yet been written to th e card (remaining capacity of the internal buf fer memory).
353 10 Image Playback This chapter explains how to play back o r erase photos and movies, how to display them on a TV screen, and other playback-related fu nctions.
354 1 Play back the image. Press the < x > button. X The last image captured or played back will appear . 2 Select an image. T o play back images starting with the last image captured, turn the < 5 > dial counterclockwise. T o play back images starting with the first captured image, turn the dial clockwise.
355 x Image Playback 3 Exit the image playback. Press the < x > button to exit the image playback and return to shooting-ready state. With the shooting information screen displayed (p.354), you can tilt < 9 > up or down to change the shooting infor mation displayed at the screen’s bottom as follows.
356 Basic information display B : Shooting Information Display Sample Information for Still Pho tos Shutter speed Folder number - File number Rating Eye-Fi card transmission status Playback number/ T .
357 B : Shooting Information Display Shooting information display • Det ailed info rmation * When you shoot in RA W+JPEG image quality , the RA W image file size will be displayed. * During flash photography witho ut flash exposure compensation, < 0 > will be displayed.
B : Shooting Information Display 358 • Lens/Histogram information • GPS information Histogram display (Brightness) Lens name Focal length Histogram display (RGB) • White balance information • .
359 B : Shooting Information Display • < > and < > modes: Shutter speed, aperture and ISO speed are not displayed. • < > mode: Aperture and ISO speed are not displayed. • < > mode: Shutter speed and ISO speed are not displayed.
B : Shooting Information Display 360 Histogram The brightness histogram shows the exp osure level distribution and overall brightness. The RGB hist ogram is for checking the color saturation and gradation. The disp lay can be switched with [ 3 3: Histogram disp.
361 Y ou can search for images quickly with th e index display showing 4, 9, 36, or 100 images on one screen. 1 Press the < u > button. During image playback or when the camera is ready to shoot, press the < u > button. X [ 6 u ] will be displayed on the lower right of the screen.
x Searching for Images Quickly 362 In the single-image display , you can turn the < 6 > dial to jump through the images forward or backward according to the jump meth od set. 1 Select [Image jump w/ 6 ]. Under the [ 3 2 ] tab, select [ Image jump w/ 6 ], then press < 0 >.
363 x Searching for Images Quickly 3 Browse by ju mping. Press the < x > button to play back images. In the single-image display , turn the < 6 > dial. X Y ou can browse by the method that was set. Playback positio n Jump method T o search images by shooting date, select [ Date ].
364 Y ou can magnify a captured image by appr ox. 1.5x to 10x on the LCD monitor . 1 Magnify the image. The image can be magnified as follows: 1. During image playback (single-image display), 2. During the image review after image capture, and 3. From the shooting-ready state.
365 u Magnifying Images Under the [ 3 3 ] tab, when you select [ Magnificatn (apx) ], you can set the starting magnification and initial position for the magnified view . 1x (no magnification) The image is not magnified. The magnified view will start with the single-image display .
366 Y ou can compare two images side by side on the LCD mon itor . In the two-image display , you can use magnified view or jump display as well as protect, rate, and delete images. 1 Set the two-image display . During image playback, press the < X > button.
367 Y ou can rotate the displayed image to the desired orientation. 1 Select [R otate image]. Under the [ 3 1 ] tab, select [ Rotate image ], then press < 0 >. 2 Select an imag e. T urn the < 5 > dial to select the image to be rotated. Y ou can also select an image in the index display (p.
368 Protecting an image prevents it from being erased accidentally . 1 Select [Protect images]. Under the [ 3 1 ] tab, select [ Protect images ], then press < 0 >. 2 Select [Select images]. X An image will be displayed. 3 Select an image. T urn the < 5 > dial to select the image to be protected.
369 K Protecting Images Y ou can protect all the images in a fo lder or on a card at once. When y ou select [ All images in folder ] or [ All images on card ] in [ 3 1: Protect images ], all the images in the folder or on the card will be protected.
K Protecting Images 370 During image playback, you can use the < c > button to protect an image. 1 Select [ m btn function ]. Under the [ 5 3 ] tab, select [ m button function ], then press < 0 >. 2 Select [Protect]. 3 Select an image. Press the < x > button to play back images.
371 Y ou can rate images (still photos and movies) w ith one of the five rating marks: l / m / n / o / p . This function is called rating. 1 Select an imag e. During image playback, turn the < 5 > dial to select an image or m ovie to be rated. Y ou can also select an image or movie on the index display (p.
Setting Ratings 372 1 Select [Rating]. Under the [ 3 2 ] tab, select [ Rating ], then press < 0 >. 2 Select an image. T urn the < 5 > dial to select an image or movie to be rated. If you press the < u > button and turn the < 6 > dial counterclockwise, you can select an image from a three- image display .
373 Setting Ratings A total of up to 999 images of a giv en rating can be displayed. If there are more than 999 images with a given rating, [ ### ] will be displayed. T aking Advantage of Ratings With [ 3 2: Imag e jump w/ 6 ], you can display only images having the specifie d rating.
374 During playback, you can press the < Q > button to set the following: [ J : Protect images ], [ b : R otate image], [ 9 : Rating ], [ R : RA W image processing] (RAW images only), [ S : Resize] (JPEG image only), [ : Highlight alert ], [ : AF po int display ], and [ e : Image jump w/ 6 ].
375 Q Quick Control for Playback T o rotate an image, set [ 5 1: Auto rotate ] to [ On z D ]. If [ 5 1: Auto rotate ] is set to [ On D ] or [ Off ], the [ b Rotate image ] setting will be recorded to the image, but the camera will not rotate the image for display .
376 Y ou can play back movies in the follow ing three ways: By connecting the camera to a TV set with HDMI Cable HTC-100 (sold separately), you can play back the camera’s still photos and movies on the TV set. Y ou can play back movies on the camera’s LCD monitor .
377 k Enjoying Movies The movie files recorded on the card can be transferred to a computer and played back with ImageBrowser EX (EOS software). Playback and Editing with a Computer (p.537) T o have the movie pla y back smoothly on a computer , use a high- performance computer .
378 1 Play back the image. Press the < x > button to display an image. 2 Select a movie. T urn the < 5 > dial to select the movie to be played. With the single-image display , the < s1 > icon displayed on the upper left indicates a movie.
379 k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing < 0 > toggles between play and stop. 8 Slow motion Adjust the slow motion speed by turning the < 5 > dial. The slow motion speed is indicated on the upper rig ht of the screen.
380 Y ou can edit out the first and last sc enes of a movie in approx. 1-sec. increments. 1 On the movie p layback screen , select [ X ]. X The movie editing panel will be displayed at the bottom of the screen. 2 Specify the p art to be edited out. Select either [ U ] (Cut beginning) or [ V ] (Cut end), then press < 0 >.
381 X Editing a Movie’s First and Last Scenes 4 Save the edited movie. Select [ W ], then press < 0 >. X The save screen will appear . T o save it as a new movie, selec t [ New file ]. T o save it and overwrite the original movie file, select [ Overwrite ], then press < 0 >.
382 Y ou can play back the images on the card as an automatic slide show . 1 Select [Slide show]. Under the [ 3 2 ] tab, select [ Slide show ], then press < 0 >. 2 Select the image s to be played. Select the desired option on the screen, then press < 0 >.
383 3 Slide Show (Auto Playback) 3 Configure [Set up] as desired. Select [ Set up ], then press < 0 >. Set the [ Display time ] and [ Repeat ] settings for still photos. After completing the settings, press the < M > button. Item Playback Description j All images All the still p hotos and movies on the card will be played back.
3 Slide Show (Auto Playback) 384 4 St art the slide show . Select [ Start ], then pr ess < 0 >. X After [ Loading image... ] is displayed, the slide show will start. 5 Exit the slid e show . T o exit the slide show and return to the setting screen, press the < M > button.
385 By connecting the camera to a TV set w ith an HDMI cable (sold separately), you can play the camera’s still photos and movies on the TV set. For the HDMI cable, HDMI C able H TC-100 (sold separately) is recommended.
Viewing Images on a TV Set 386 If the TV set connected to the camera with an HDMI cable is compatible with HDMI CEC*, you can use the TV set’s remote control for playback operations. * An HDMI-st andard function enabling HDMI devices to co ntrol each other so t hat you can control them with one remote cont rol unit.
387 Viewing Images on a TV Set 3 Press the came ra’ s < x > button. X An image will appear on the TV screen and you can use the TV set’s remote control to play back images. 4 Select an imag e. Point the remote control toward the TV set and press the / button to select an image.
388 The images recorded on one card can be copied to another card. 1 Select [Image copy]. Under the [ 3 1 ] tab, select [ Image copy ], then press < 0 >. 2 Select [Sel.Image]. Check the copy source and target cards’ number , and remaining capacity .
389 a Copying Images 4 Select the images to be copied. T urn the < 5 > dial to select an image to be copied, then press < 0 >. X The [ X ] icon will appear on the upper left of the screen. If you press the < u > button and turn the < 6 > dial counterclockwise, you can select an image from a three- image display .
a Copying Images 390 8 Select [ OK]. Check the information of the source card and target card, then select [ OK ]. X The copying will start and the progress will be displayed. When the copying is completed, the result will be displayed. Select [ OK ] to return to the screen in step 2.
391 a Copying Images The file name of th e copied image will be the same as the source image’s fil e name. If [ Sel.Image ] is set, you cannot copy images in multiple folders at once.
392 Y ou can either select and erase unne cessary images one by one or erase them in one batch. Protected images (p.368) will not be erased. Once an image is erase d, it cannot be recovere d. Make sure you no longer need the i mage before erasing it. T o prevent impor tant images from being eras ed accidentally , protect them.
393 L Erasing Images 2 Select [Se lect and erase images]. X An image will be displayed. If you press the < u > button and turn the < 6 > dial counterclockwise, you can select an image from a three- image display . T o return to the single- image display , turn the < 6 > dial clockwise.
394 The LCD monitor ’s brightness is adjusted automatically for optimum viewing depending on the ambient light level. Y ou can also set the automatic adjustment’s brightness leve l (brighter or darke r), or adjust the brightness manually . 1 Select [LCD brig htness].
395 Changing Image Playback Settings V ertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the computer instead of horizontally . Y ou can change the setting for this feature. 1 Select [A uto rotate].
396.
397 11 Post-Processing Images Y ou can process RAW images with the camera or resize (reduce the resolutio n of) JPEG images. A M icon at the upper right of a page title indicates a function that can be used only in these modes: < d > < s > < f > < a > < F >.
398 Y ou can process 1 images with the camera and save them as JPEG images. As the RAW image it self does not change, you can apply different processing conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera.
399 R Processing RAW Images with the Camera N Displaying the setting screen Press < 0 > to display the setting screen. Turn the < 5 > or < 6 > dial to change the setting. Press < 0 > to finalize the setting and return to the previous screen.
R Processing RAW Images with the Camera N 400 Brig htness adjustment Y ou can adjust the ima ge brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance ( p.168) Y ou can select the white b alance.
401 R Processing RAW Images with the Camera N Col or space (p.187) Y ou can select eithe r sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illu mination correction (p.
R Processing RAW Images with the Camera N 402 Peripher al Illumination Co rrecti on, Distortion Correction, and Chromatic Aber ration Correction T o execute peripheral ill umination co rrection, distort ion correction, and chromatic aberrati on correction with the camera, the correction dat a of the lens used must be regi stered in the camera.
403 Y ou can resize a JPEG imag e to make the pixel count lower and save it as a new image. Resizing an ima ge is possible only w ith JPEG 3 / 4 / a / b images. JPEG c and RAW images cannot be resized. 1 Select [R esize]. Under the [ 3 2 ] tab, select [ Resize ], then press < 0 >.
S Resizing JPEG Images 404 Resize Options by Orig inal Image Size Image sizes by aspect ratio are show n in the table below . The image- recording quality figures marked with an asterisk do not exactly match the aspect ratio. The image will be cropped slightly .
405 12 Sensor Cleaning The camera has a Self Cleaning Se nsor Unit to automatically shake off dust adhered to the image sensor ’s front layer (low pass filter). The Dust Delete Data can also be appended to the image so that the dust spots remaining can be deleted automatically by Digital Photo Professional (EOS software , p.
406 Whenever you set the power switch to < 1 > or < 2 >, the Self Cleaning Sensor Unit operates to aut omatically sh ake off the dust on the front of the sensor . Normally , you need not pay attention to this operation. However , you can choos e to perform sensor cleaning manually , or disable it.
407 Normally , the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. Ho wever , in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later . The Dust Delete Data is used by Digital Photo Professional (EOS software , p.
3 Appending Dust Delete Data N 408 3 Shoot a solid-white object. At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in aperture- priority AE mode at an aperture of f/22.
409 Dust that could not be removed by the auto matic sensor cleaning can be removed manually with a commercially- available blower , etc. Before cleaning the sensor , detach the lens from the camera. The image sensor is extrem ely delicate. If the sensor needs to be cleaned directly , having it done by a Canon Se rvice Center is recommended.
3 Manual Sensor Cleaning N 410 While cleaning the sensor , never do any of the following. If the power is cut off, the shutter will close and the shutter curtains and image sensor may get damaged. • Setting the power switch to < 2 >. • Removing or inserting the battery .
411 13 Printing Images and Transferring Images to a Computer Printing (p.414) Y ou can connect the camera directly to a printer a nd print out the images on the ca rd. The camera is compliant with “ w PictBridge”, which is the standard for direct printing.
412 The direct printing proced ure can be performed entirely with th e camera while you look at the camera’s LCD monitor . 1 Set the camera’ s power switch to < 2 >. 2 Set up the printer . For details, refer to the printer ’s instruction manual.
413 Preparing to Print 6 Play back the image. Press the < x > button. X The image will appear with the < w > icon on the upper left of the screen to indicate that the camera is connected to a printer . Make sure the printer has a PictBridge connect ion port.
414 The screen display and setting o ptions will differ depending on the printe r . Some settings may not be available. For details, refer to the printer ’s instruction manual. 1 Select the im age to be printed. Check that the < w > icon is displayed on the upper left of the LCD monitor .
415 w Printing Select the size of the paper loaded in the printer , then press < 0 >. X The paper type screen will appear . Select the type of the paper loaded in the printer , then press < 0 >. X The page layout screen will appear . Select the page layout, then press < 0 >.
w Printing 416 4 Set the printing effects. Set them if necessary . If you do not need to set any printing effects, go to step 5. Contents displayed on the screen differ depending on the printer . Select the setting, then press < 0 >. Select the desired printing effect, then press < 0 >.
417 w Printing 5 Set the date and file number imprinting. Set them if necessary . Select < I >, then press < 0 >. Set the print settings as desired, then press < 0 >. 6 Set the number of copies. Set it if necessary . Select < R >, then press < 0 >.
w Printing 418 In step 4 on page 416, select the printing effect. When the < z e > icons are displayed brightly , you can press the < B > button. Y ou can then adjust the printing effects. What can be adjusted or what is displayed will depend on the selection made in step 4.
419 w Printing Y ou can crop the image and pr int only an enlarged version of the cropped portion, as if the image is recomposed. Set the cropping right befo re printing. If you change the print settings after setting the cropping, you may have to set the cropping again before printing.
w Printing 420 If the image’s aspect rati o is different from the printing paper ’s aspect ratio, the image may be cropped signif icantly when you print it as a borderless print. If the image is cropped , the print may look gr ainier due to the fewer number of pixels.
421 Y ou can set the print type, dat e imprinting, and file number imprin ting. The print settings will be applied to all print-o rdered images. (They cannot be set indivi dually for each image .) 1 Select [Pri nt order]. Under the [ 3 1 ] tab, select [ Print order ], then press < 0 >.
W Digital Print Order Format (DPOF) 422 4 Exit the setting. Press the < M > button. X The print order screen will reappear. Next, select [ Sel.Image ], [ By n ], or [ All image ] to order the images to be printed. Print typ e K S tandard Prints one image on one sheet.
423 W Digital Print Order Format (DPOF) Sel.Image Select and order images one by one. If you press the < u > button and turn the < 6 > dial countercloc kwise, you can select an image from a three-image display . T o return to the single-image display , turn the < 6 > dial clockwise.
424 With a PictBridge printer , you can easily print images with DPOF . 1 Pre pare to print. See page 412. Follow the “Connecting the Camera to a Printer” procedure up t o step 5. 2 Under the [ 3 1] t ab, select [Print order]. 3 Select [Print]. [ Print ] will be displayed only if the camera is connected to a printer and printing is possible.
425 Y ou can connect the camera to a comp uter and operate the camera to transfer images on the card to the computer. This is called direct image transfer . The direct image transfer can b e performed with the ca mera while you look at the LCD monitor .
d Transferring Images to a Computer 426 3 Set the camera’ s power switch to < 1 >. When the computer displays a screen to select the program, select [ EOS Utility ]. X The EOS Utility screen will appear on the computer . For RA W+JPEG images, you can specify which image to transfer .
427 d Transferring Images to a Computer Sel.Image 1 Select [Imag e transfer]. Under the [ 3 2 ] tab, select [ Image transfer ], then press < 0 >. 2 Select [I mage sel./tr ansfer]. 3 Select [Se l.Image]. 4 Select the images to be transferred. T urn the < 5 > dial to select the image to be transferred, then press < 0 >.
d Transferring Images to a Computer 428 5 T ransfer the image. On the computer screen, check that EOS Utility’s main window is di splayed. Select [ Direct transfer ], then press < 0 >. On the confirmation screen, select [ OK ], and the images will be transferred to the computer .
429 Y ou can specify up to 998 images to be printed in a photobook. When you use EOS Utility (EOS software) to transfer images to a computer , the specified images will be copied to a dedicated folder . This function is useful for ordering photobooks online.
p Specifying Images for a Photobook 430 Y ou can specify all the images in a fold er or on a card at once. When [ x 1: Photobook Set-up ] is set to [ All images in folder ] or [ All images on card ], all the images in the folder or on the card will be specified.
431 14 Customizing the Camera Y ou can customize various camera function s to suit your picture-taking preferen ces with Custom F unctions. Also, current camera sett ings can be saved under < w > < x > < y > positions of the Mode Dial.
432 3 Custom Functions N 8 1: Exposure A LV Shooting k Movie Shooting Exposure level increments p.434 k k ISO speed setting increment s k In a Bracketing aut o cancel k (S till photo, with WB bracketing) Bracketing se quence p.435 k Number of bracketed shots k Safety sh ift p.
433 3 Custom Functions N Selecting [ 8 5: Clear all Custom Fun c. (C.Fn) ] will clear all the Custom Function settings. 8 3: Display/Op eration A LV Shooting k Movie Shooting Focusing scr een p.440 Wa r n i n g s z in viewfind er p.441 L V shooting area dis play k Dial directi on during Tv/Av p.
434 Under the [ 8 ] tab, you can customize various camera features to suit your picture-taking pref erences. Any settings different from the default will be displayed in blue.
435 3 Setting Custom Functions N Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0-+: 0, -, + -0+: -, 0, + +0-: +, 0, - Number of brac keted shots The number of shots taken with AEB and white balance bracketing can be changed from the default, 3 shots, to 2, 5, or 7 shots.
3 Setting Custom Functions N 436 Safety shift OFF: Disable Tv/A v: Shutte r speed/Aperture This takes effect in the shutter-priority AE ( s ) and aperture - priority AE ( f ) modes.
437 3 Setting Custom Functions N Same exposure for new apertu re If the < a > mode (man ual exposu re shoo ting) i s set a nd the I SO speed is set manual ly (other tha n Auto ISO), th e maximum aperture’ s f/number m ay change to a higher numb er (smalle r apertu re) if you d o any of the foll owing: 1.
3 Setting Custom Functions N 438 C.Fn2: Exposu re/Drive Set shutter speed range Y ou can set the shutter speed rang e. In the < s > < a > modes, you can set the shutter speed manually within t he shutter speed range that you have set.
439 3 Setting Custom Functions N Continuous s hooting speed Y ou can set the continuous shooting speed for < o > high-speed continuous shooting, < i > low-speed continuous shooting, and < M > silent continuous shooting. High speed Y ou can set it fro m 2 to 10 frames per second (fps).
3 Setting Custom Functions N 440 C.Fn3: Display/Operation Focusing Screen T o suit your shooting needs, you can change to an optional focusing screen, sold separately . If you change the focusing screen, be sure to change this setting to match the focusing screen type.
441 3 Setting Custom Functions N Wa r n i n g s z in viewfinder When any of the following functions are set, the < z > icon can be displayed in the viewfinder and on the LCD panel (p.26-27). Select the function for which you want the warning icon to appear , and press < 0 > to append a < X >.
3 Setting Custom Functions N 442 Dial directio n during Tv/A v : Normal : Reverse direction Dial turning direction when setting the shutter speed a nd aperture can be reversed. In the < a > shooting mode, the turning direction of th e < 6 > and < 5 > dials will be reversed.
443 3 Setting Custom Functions N C.Fn4: Othe rs Add cropping information If you set cropping inform ation, vertic al lines for th e aspect ratio you have set will appear on the Live View image. Y ou can then compose the shot as if you were shooting with a medium- or large-format camera (6x6 cm, 4x5 inch, etc.
3 Setting Custom Functions N 444 Default Erase option During image playback and image review after image capture, when you press the < L > button, the erase menu ap pears (p.392). Y ou can set which option, [ Cancel ] or [ Erase ], is to be preselected on this screen.
445 Y ou can assign often-used function s to camera buttons or dials according to your preferences. 1 Select [ 8 3: Custom Controls]. Under the [ 8 3 ] tab, select [ Custom Controls ], then press < 0 >. X The Custom Controls screen to select control buttons and dials will appear .
8 3: Custom Controls N 446 Assignable Function s to Camera Controls Function Page Metering and AF start 450 k k * 1 k * 1 AF stop 452 kk Switch to registere d AF function ONE SHOT z AI SERVO k k Switc.
447 8 3: Custom Controls N * The AF stop button ( ) is provided only on super telephot o IS lenses. * p k kk k * 2 k * 2 k k k * 3 k * 3 k * 4 k k * 5 k k kkk k k k k k k k k k k k k k k k k.
8 3: Custom Controls N 448 Function Page One-touch image quality setting 456 One-touch image quality (hol d) Image quality Picture S tyle 457 Depth-of-field preview 457 IS star t Menu display Register.
449 8 3: Custom Controls N * The AF stop button ( ) is provided only on super telephot o IS lenses. * p k * 6 k * 6 k * 6 k * 6 k k k kk k k k k k k k k k k k k.
8 3: Custom Controls N 450 When you press the button assigned to this function, metering and AF are executed. *1: When assigned to the < p > or < A > button, pressing the < B > button while the setting screen is displayed will enable you to set the detailed AF settings.
451 8 3: Custom Controls N AI Servo AF characteristics (p.108) Press the < p > or < A > button to perform AF with the set case from [ Case1 ] to [ Case6 ]. AF operation (p.86) Press the < p > or < A > button to perform AF with the set AF operation.
8 3: Custom Controls N 452 The AF will stop while you hold down the b utton assigned to this function. Convenient when you want to stop the AF during AI Servo AF . After setting and assigning this function to a button, you can apply the following settings by holding down the assigne d button for AF: AF area selection mode (p.
453 8 3: Custom Controls N During metering, tilting < p > to the right will switch between the current AF point and the center AF point or registered AF po int. *4: On the setting screen, when you press the < B > button, you can select [ Switch to center AF point ] or [ Switch to registered AF point ].
8 3: Custom Controls N 454 When you press the shutter button halfway , only the exposure metering is performed. When you press the button assigned to this function, you can lock the exposure (AE lock) during metering.
455 8 3: Custom Controls N Y ou can set the ISO speed by holding dow n < 0 > and turning the < 6 > dial. If this control is used while Auto ISO is set, manual ISO speed setting will take effect.
8 3: Custom Controls N 456 In manual exposure < a >, you can set the apertur e with the < 5 > or < 6 > dial. Pressing the button assigned to this function will switch to the image- recording quality set here.
457 8 3: Custom Controls N Press < 0 > to display the Picture S tyle selection setting screen on the LCD monitor (p.160). When you press the depth -of-field preview button, the apertur e will stop down and you can check the depth of field (p.221).
8 3: Custom Controls N 458 Pressi ng < 0 > will play back images. Press < 0 > to magnify or reduce the images reco rded on the card. See page 364 for the operation procedure. During Live View or movie shooting (except u +Tracking), you can also magnify the image (p.
459 Under My Menu tab, you can register menu items and Custom Functions whose settings you change frequently . Y ou can also name the registered menu tabs and press the < M > button to display the My Menu tab first. 1 Select [A dd My Menu tab]. Under the [ 9 ] tab, select [ Add My Menu t ab ], then pr ess < 0 >.
3 Registering My Menu N 460 2 Select [Select items to register]. 3 Register the desired items. Select the desired item, then press < 0 >. Select [ OK ] on the confirmation dialog. Y ou can register up to six items. T o return to the screen in step 2, press the < M > button.
461 3 Registering My Menu N Delete tab Y ou can delete the My Menu tab currently displayed. Select [ Del ete tab ] to delete the [ MY MENU* ] tab. Rename tab Y ou can rename the My Menu tab from [ MY MENU* ]. 1 Select [R ename tab]. 2 Enter text. Press the < L > button to delete any unnecessary characters.
3 Registering My Menu N 462 Y ou can delete all My Menu tabs and delete all My Menu items. Delete all My Menu tabs Y ou can delete all My Menu tabs. When you select [ Delete all My Menu tabs ], all the t abs from [ MY MENU1 ] to [ MY MENU5 ] will be deleted and the [ 9 ] tab will revert to its default.
463 3 Registering My Menu N Y ou can select [ Menu display ] to set the menu screen that is to appear first when you press the < M > but ton. Normal display Displays the last displayed menu s creen. Display from My Menu t ab Displays with the [ 9 ] tab selected.
464 Y ou can register current camera se ttings, su ch as the shooting mode, menu functions, and Custom Functi on settings, as Custom sh ooting modes under the Mode Dia l’s < w >, < x >, and < y > positions. 1 Select [Custom shooting mode (C1-C3)].
465 w : Registering Custom Shooting Modes N Shooting f unctions Shooting mode, Shutter speed, Aperture, ISO speed, AF operation, AF area selection mode, AF point, Drive mode, Metering mode, Exposure c.
w : Registering Custom Shooting Modes N 466 [ 2 4 ] Lens drive when AF impossible, Selectable AF point, Select AF area selection mode, AF area selection method, Orientation linked AF point, Initial AF.
467 15 Reference This chapter provides reference information for camera features, system accessories, etc. Certification Logo Select [ 5 4: Certification Logo Display ] and press < 0 > to display some of the logos of the camera’ s certifications.
468 If you press the < B > button when the camera is ready to shoot , the scree ns for the [ Displays camera settings ], [ Electronic level ] (p.
469 B Button Functions Pressi ng the < Q > button enables Quick Control of the shooting settings (p.61). When you press the < n >, < o >, < m >, or < S > button, the setting screen appears and you can use < 6 >, < 5 >, < B >, or < 9 > to set it.
470 Y ou can check the battery’s condition on th e LCD monitor . Each Battery Pack LP-E 6N/LP-E6 has a unique serial number , and you can register multiple ba ttery pack s to the camera . When you us e this feature, yo u can check the re gistered battery pack’ s remaining c apacity and operation history .
471 3 Checking the Battery Information Y ou can register up to six LP-E6N/LP- E6 battery packs to the camera. T o register multiple battery packs to the camera, follow the procedure below for each battery pack. 1 Press the < B > button. With the battery info.
3 Checking the Battery Information 472 It is convenient to label all register ed Battery Pack LP-E6N/LP-E6 with their serial numbers, using commercially-available labels. 1 Write the serial number on a label. Write the serial number displayed on the battery history screen on a label approx.
473 3 Checking the Battery Information Y ou can check the remaining capacity o f any battery pack (even when not installed) and also when it was last used. Look for the serial number . Refer to the battery’s serial number label and look for the battery’s serial number on the battery history screen.
474 With AC Adapter Kit ACK-E6 (sold separately), you can conn ect the camera to a household power outlet and do not have to worry about the remaining battery level. 1 Connect the DC Co upler ’s plug. Connect the DC Coupler ’s plug to the AC Adapter ’s socket.
475 With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer, or upload them to an online service via a wireless LAN.
H Using Eye-Fi Cards 476 4 Display the connection information. Select [ Connection info. ], then press < 0 >. 5 Check the [Access point SSID:]. Check that an access point is displayed for [ Access point SSID: ]. Y ou can also check the Eye-Fi card’s MAC address and firmware version.
477 H Using Eye-Fi Cards Cautions for U sing Eye-Fi Cards If “ ” is displayed, an error occurred while ret rieving the card information. T urn th e camera’s power switch off, an d on again. Even if [ Eye-Fi trans. ] is set to [ Disable ], it may still transmit a signal.
478 System Map 90EX ST -E2 270EX II 320EX 600EX-RT/ 600EX 430EX II ST -E3-RT Macro Ring Lite MR-14EX II Macro T win Lite MT -24EX Angle Finder C Hand Strap E2 Leather Case EH20-L Battery Magazine BGM-.
479 System Map *1: Battery Pack LP-E6 can also be used. *2: T o use the older model WFT-E7 (not V ersion 2), the firmware must be updated and Interface Cable IFC-40AB II or IFC-150AB II must be used. *3: With IFC-500U II, the communication speed will be equivalent to Hi-Speed USB (USB 2.
480 o : Set automatically k : User select able : Not select able/Disabled Function Availa bility Table Acc ording t o Shooti ng Mode Still Photo Shooting Function A d s f a F All image quality setting.
481 Function Availability Table According to Shooting Mode *1: If the built-in flash is set to < b >, the AF-assist beam will not be emitted. *2: Setta ble only during Live View shooting. *3: With Auto IS O, you can set a fixed ISO spe ed. *4: Setta ble only when Auto ISO is set.
Function Availability Table According to Shooting Mode 482 o : Set automatically k : User select able : Not select able/Disabled *1 : Th e z icon indicates still photo shooting during movie shooting.
483 Function Availability Table According to Shooting Mode *3 : With Auto ISO, you can set a fixed ISO speed. *4 : With Aut o ISO, you ca n set exposure compensation.
484 z : Shooting 1 (Red) Page Menu Settings Viewfinder Shooting an d Live View Shooti ng Image quality 1 / 41 / 61 149 73 / 83 / 74 / 84 / 7 a / 8 a / b / c Image review t ime Off / 2 sec.
485 Menu Settings z : Shooting 2 (Red) Page * During movie shooting, [ Expo.comp./AEB ] will be [ Exposure comp. ]. z : Shooting 3 (Red) Exposure compensation/ AEB setting* 1/3- and 1/2-stop increment.
Menu Settings 486 z : Shooting 4* (Red) Page * In the < A > mode, these menu options are displayed under [ z 2 ]. z : Shooting 5* (Red) * In the < A > mode, these menu options are displayed under [ z 3 ].
487 Menu Settings 2 : AF1 (Purple) Page 2 : AF2 (Purple) 2 : AF3 (Purple) Case 1 V ersatile mul ti purpose setting 109 Case 2 Continue to t rack the subjects, ignoring possible obstacles 109 Case 3 In.
Menu Settings 488 2 : AF4 (Purple) Page 2 : AF5 (Purple) Lens drive when AF impossible Continue focus search / Stop focus sear ch 122 Select able AF point 65 points / 21 points / 9 poin ts 123 Select .
489 Menu Settings 3 : Playback 1 (Blue) Page 3 : Playback 2 (Blue) 3 : Playback 3 (Blue) * The setting is linked to the [ Time code ]’s [ Movie play count ] under the [ z 5 (Movi e) ] tab.
Menu Settings 490 5 : Set-up 1 (Y el low) Page 5 : Set-up 2 (Y el low) Record function+card/ folder sel ection Record func tion: S tandard / Auto swi tch card / Record separately / Re cord to multiple.
491 Menu Settings 5 : Set-up 3 (Y el low) Page * Options displayed o n the screen diff er depending on the [ V ideo system ] setting. 5 : Set-up 4 (Y el low) Video system For NTSC / For P AL 330 385 B.
Menu Settings 492 8 : Custom Funct ions (Orange) Page 9 : My Menu (Green) C.Fn1: Exposure Customize camera functions as desired 434 C.Fn2: Exposure/Drive 438 C.
493 Menu Settings z : Shooting 4 *1 (Movie) (Red) Page * In the < A > mode, these menu options are displayed under [ z 2 ]. * In the < A > shooting mode, [ Sound recording ] settings will be [ On ] [ Off ].
Menu Settings 494 z : Shooting 5 * 1 (Movie) (Red) Page *1: In the < A > mode, these menu o ptions are displayed under [ z 3 ]. *2: The setting is li nked to [ Movie play count ] under th e [ x 3 ] tab. *3: Displayed when 8 (59.94 fps) or 6 (29.
495 If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this T roubleshooting Guide does not resolve t he problem, contact your dealer or nearest Canon Service Center . If the battery’ s remaining cap acity is 94% or highe r , the battery will not be rechar ged (p.
Troubleshooting Guide 496 If the power is turned of f while an image is being rec orded to the card, the access lamp will rema in on or continue to blink for a few seconds. When the image rec ording is com pleted, th e po wer will turn off automatically .
497 Troubleshooting Guide During inter val timer shoot ing, auto pow er off will not take effect (p.250) . The ca mera cannot be used with EF-M l enses (p.50) . Install a rech arged battery p ack in the camera (p.38). Make sure the card is properly inse rted (p.
Troubleshooting Guide 498 If [ z 4: Mirro r lockup ] is set to [ Enable ], set it to [ Disable ]. Set the lens’ s focus mode switch to < AF > (p.50). Press the shutter button ge ntly to prevent camera shak e (p.54-55). If the lens has an Image S tabi lizer , set the IS s witch to < 1 >.
499 Troubleshooting Guide Duri ng Live View shoot ing and movi e shooting, the AF cont rol metho d (phase-differ ence detect ion with the ima ge sensor or contr ast detection ) switches aut omaticall y depending on the lens typ e and function us ed such as magnif ied view.
Troubleshooting Guide 500 If [ z 3: Highlight tone priority ] is s et to [ Enable ], the settable IS O speed ran ge will be IS O 200 - ISO 1600 0. Even if you e xpand the settable ISO speed r ange with [ ISO speed range ], you cannot select the H1 (equ ivalent to ISO 2 5600) or H2 (equ ivalent to ISO 51 200).
501 Troubleshooting Guide When t he image-re cording qual ity is set to 41 or 61 , the multiple-ex posure imag e will be recor ded in 1 quali ty (p.245 ). If y ou shoot at nig ht when the ba ckground is da rk, the shut ter speed automatical ly becomes slow (slow-syn c shooting) so that both the subject a nd backgrou nd are properly e xposed.
Troubleshooting Guide 502 If y ou use a flash un it other t han an EX-seri es S peedli te, the flas h will always be fired at fu ll output (p.260). When the external S peedlite’s Custom Function setting for [ Flas h metering mode ] is set to [ TTL flash metering ] (autoflas h), the flas h will always be fire d at full output (p.
503 Troubleshooting Guide If the card’s writing speed is slow , movie sho oting may stop automatically . For cards that can r ecord movies, see p age 5. T o find out the card’s writi ng speed, ref er to the card manufacturer ’s website. If t he movie shoo ting time re aches 29 min.
Troubleshooting Guide 504 Flickering, horiz ontal stripe s (noise), or ir regular exposure s can be caused by flu orescent li ghting, LED lig hting, or ot her light so urces during movie shooting. Also , changes i n the exposure (brightnes s) or color tone may be recorded.
505 Troubleshooting Guide Set t he < R > switc h to the left (loc k release, p. 59). Check the [ 8 3: Mu lti function lock ] setting (p.442). Check the [ 8 3: Cu stom Controls ] setting (p.445). In th e < A > mode, only c ertain menu tabs and option s are display ed.
Troubleshooting Guide 506 Check that the co rrect date an d time are set ( p.47). Check the time zone an d daylight sa ving time (p. 47-48). The s hooting da te and ti me do not ap pear in t he picture . The date and time are reco rded in the imag e data as shooting information.
507 Troubleshooting Guide [ 3 3: High light alert ] is set to [ Enable ] (p.359). [ 3 3: AF point disp. ] is s et to [ Enable ] (p .359). If t he image is prot ected, it c annot be erase d (p.368). Movies edited with a computer using ImageBrow ser EX (EOS software, p.
Troubleshooting Guide 508 Set t he [ 5 3: Video system ] correctly to [ For NTSC ] or [ For P AL ]. Check that the HDMI cab le’s plug is inser ted all the way in (p.385). If [ z 5: HDMI output+LCD ] is set to [ Mirroring ], the movie will not appear on the TV set via HDMI outp ut even durin g playback.
509 Troubleshooting Guide If you selected [ C lean now f ], th e shutter will make a noise, but no picture i s taken (p.4 06). If y ou repeatedl y turn the power switch < 1 > / < 2 > at a short interval, th e < f > icon may not be displayed (p.
510 If there is a problem with the ca mera, an error message will appear . Follow the on- screen instructions. * If the error still persist s, write down the error number and cont act your nearest Canon Service Center . Error Codes Number Error Message and Solution 01 Communications between the camera and lens is faulty .
511 •T y p e T ype: Digital, single -lens reflex, AF/AE camera with built-in flash Recording media: CF cards (Type I, UDMA 7 supported) SD/SDHC*/SDXC* memory cards * UHS-I cards compat ible.
Specifications 512 White balance: Auto, Preset (Daylight, Shade, C loudy , T ungsten light, White fluorescent light, Flas h), Custom, Color temp erature setting (approx.
513 Specifications AF area selection mode: Single-point S pot AF (manual selection), Single-point AF (manual selection), AF point exp ansion (manual selection: up, down, lef t, and right), AF point ex.
Specifications 514 AE lock: Auto: Applied in One-Shot AF mode wit h evaluative metering when focu s is achieved Manual: By AE lock button Interval timer: Shooting inte rval and shot count settable Bul.
515 Specifications •F l a s h Built-in flash: Retract able, auto pop-up flash Guide number: Approx. 1 1/36.1 (ISO 100, in meters/feet) Flash coverage: Approx.
Specifications 516 Compression method: ALL-I (For editing/I-on ly), IPB (S tandard), IPB (Light) * IPB (Li ght) is fo r MP4 only. File size: [MOV] • Full HD (59.94p/ 50.00p)/IPB (S tandard) : Approx. 440 MB/min. • Full HD (29.97p/ 25.00p/24.00p/23.
517 Specifications [SD card] ALL-I: 20 MB/sec. or faster IPB (S tandard), Full HD 59. 94p/50.00p: 20 MB/sec. or faster IPB (S tandard), ot her than above: 6 MB/sec.
Specifications 518 •L C D M o n i t o r T ype: TFT color , liquid-crystal moni tor Monitor size and dots: Wide 7.7 cm (3.0-in) (3:2) with approx. 1.04 million dot s Brightness adjustment: Auto (Dark.
519 Specifications • Direct Pr inting Compatible printe rs: PictBridge-compatible pri nters Printable i mages: JPEG and RA W images Print ordering: DPOF V ersion 1.
Specifications 520 •P o w e r Battery: Battery Pack LP-E6N/LP-E6, quantit y 1 * AC power can be supplied via AC Adapter Kit ACK-E 6. * With Battery Gr ip BG-E16 attached, size-AA/LR6 batteries can be used.
521 Specifications • Battery C harger LC-E6 Compatible battery: Battery Pack LP-E6N/LP-E6 Recharging time: Approx. 2 hr . 30 min. Rated input: 100 - 240 V AC (50/60 Hz) Rated output: 8.4 V DC / 1.2 A Working temperat ure range: 5°C - 40°C / 41°F - 104°F Working humidit y: 85% or less Dimensions (W x H x D): Approx.
Specifications 522 • EF-S15-85 mm f/3.5-5.6 IS USM Focal length/Aperture: 15 mm-85 mm / f/3.5-5.6 Lens construction: 17 elements in 1 2 groups Minimum aperture: f/22 - 36 * f/22-38 when 1/2 stop inc.
523 The EF-S18-135mm f/3.5-5.6 IS STM kit lens uses a stepping motor that drives the focus lens (for achi eving focus). T he motor controls the focus lens even during zooming. 1. When the camera is OFF The motor does not operate while th e camera is OFF or when the camera is OFF due to the auto power off function.
524 T rademarks Adobe is a trademark of Adobe Systems I ncorporated. Microsoft and Windows are trademarks or registered trademar ks of Microsoft Corporation in the United S tates and/ or other countries. Macintosh and Mac OS are trade marks of Apple Inc.
525 Use of Genuine Canon Accessories Is Re commended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage t o this product and/or accidents such as fire, etc., caused by the malfunctio n of non-genuine Canon accessories (e.
526 The following precautions are provided to pr event harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the produ ct. If you experience any malfunctions, p roblems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased t he product.
527 Safety Precautions Whe n the camera or accessories are not in use, make sure to remove the battery and disconnect the power plug from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, or corrosion. Do n ot use the equipment where there is flammable gas.
Safety Precautions 528 Cautions: Follow the cautions below. Otherwise, physical injury or property damage may result. Do not use or store the product inside a car under the hot sun or ne ar a heat source. The product may become hot and cause skin burns.
529 Only for European Union and EEA (Norway , Iceland and Liechtenstein) These symbols indicate that this product is not to be disposed of with your household wast e, according to the WEEE Directive (2012/19/E U), the Battery Directive (2006/66 /EC) and/or national legislat ion implementing those Directives.
530.
531 16 Viewing the DVD-ROM Instruction Manuals / Downloading Images to Your Comp uter This chapter explain s how to view the Camera and Software Instruction Manual s (on the DVD-ROM provided) on your .
532 The EOS Camera Instruction Manuals Disk (D VD-ROM) contains the following elec tronic manuals (PDF files): Instruction Manual Explains all the camera functi ons and procedures, including basic content. Sof tware Instruction Manuals Software Instruction Manuals PDFs for the software supplied on the EOS Solution Disk (see p.
533 Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) [ WINDOWS ] EOS Camera Instru ct ion Manuals Disk Copy the PDF Instruction Manuals contained on the disk to your computer . 1 Insert the EOS Camera Instruction Manuals Disk (DVD) into the DVD-ROM drive of your computer .
Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) 534 [ MACINTOSH ] EOS Camera Instruction Manuals Disk Copy the PDF Instruction Manuals contained on the disk to your computer . 1 Insert the EOS Camera Instruction Manuals Disk (DVD) into the DVD-ROM drive of your Macintosh.
535 Y ou can use EOS software to download the images in the camera to your computer . There are two ways to do this. 1 Install the sof twar e (p.539) . 2 Use the provided interfac e cable to connect the cam era to your computer . Use the interface cable p rovided with the camera.
Downloading Images to a Computer 536 Y ou can use a card reader to download images to your computer . 1 Install the sof twar e (p.539) . 2 Insert the card into the card reader . 3 Use Canon sof tware to download the images. X Use Digital Photo Professional.
537 EOS Solution Disk This disk contains various software for EOS cameras. Communication Software f or the Camera and Computer Y ou can download i mages (still images/movies) you have shot with the camera to your comput er . Y ou can set the various settings of the ca mera from your computer .
About the Software 538 An Internet connection is necessary to install the software below . Insert the EOS Solution Disk into your Internet-connected computer . Image Viewi ng and Editing Software Connect to the Internet to download and inst all the software.
539 Compatible OS 1 Check that the camera is not connected to your computer . 2 Insert the EOS Solution Disk (CD). 3 Select your geographic ar ea, country and language. 4 Click [Easy Inst allation] to start installation. Follow the on-screen instructions to complete the installation procedure.
Installing the Software 540 Compatible OS 1 Check that the camera is not connected to your computer 2 Insert the EOS Solution Disk (CD). On your computer ’s desktop, double-click and open the CD-ROM icon, and then double-click [ setup ]. 3 Select your geographic area, country and language.
541.
542 Index Numerics 10- or 2-s ec. self-t imer .......... ........ 143 1280x720 (movie) ..................... .... 331 1920x1080 (movie) ................... .... 331 24.00p ...... ........... .......... ........... ..... 333 640x480 (movie) ..... .....
543 Index C w (Custom shooting) ................ ... 464 Cable.........3, 385, 412, 4 25, 478, 53 5 Protecto r ............. ............. ........... 34 Camera Camera shak e ......... ..... 53, 54, 24 6 Clearing the c amera settings ...... 70 Holding the c amera .
544 Index Exposure sim ulation .................. ... 296 External S peedlite 9 Flash Eyecup ........ .......... ........... .......... ... 247 Eye-Fi card s.......... ............. ........... 475 Eyepiec e cover ........ .......... ..... 33 , 247 F FE lock .
545 Index Image du st preventio n ......... ......... 405 Image-recording qualit y ........ 149, 330 Image re view time ........... .......... ...... 70 Image Stabilizer (lens) .............. ...... 53 Images AF point d isplay ....... ........... ....
546 Index Log data .............. .......... ........... 211 Long exposure noise reduction..... 178 Long exposures ............. ............... 230 Low-speed continuous shoot ing ... 141 M M (Manual exposu re) ........... . 222, 320 Magnification....
547 Index N Noise reduction High ISO speed .. ............. ......... 176 Long expo sures ....... ............. .... 178 Nomenclatu re.......... ........... ............. 22 Non-Canon flash units ..................260 Normal (image-recording qualit y) .
548 Index Sepia (Monochrome) .................... 165 Sharpness....... ..................... ......... 164 Shooting funct ion settings....... 60, 469 Shooting in formation display. ........ 356 Shooting modes ........... ............. 29, 60 Av (Aperture-pr iority AE) .
549.
CANON INC. 30-2 Shimomaruko 3-chome, Ohta-ku, T okyo 146-8501, Japan Europe, Africa & Middle East CANON EUROP A N.V . PO Box 2262, 1 180 EG Amstelveen, The Netherlands For your local Canon office, please refer to your warranty card or to www .canon-europe.
デバイスCanon EOS 7D Mark IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Canon EOS 7D Mark IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCanon EOS 7D Mark IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Canon EOS 7D Mark IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Canon EOS 7D Mark IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Canon EOS 7D Mark IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCanon EOS 7D Mark IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Canon EOS 7D Mark IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCanon EOS 7D Mark IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
