AEGメーカー2020 Dの使用説明書/サービス説明書
ページ先へ移動 of 20
2020 D Cooker Hood Operating and Installation Instructions.
2 For the User Important Safety Information Y our Appliance Operating Instructions Cooker Hood Controls T o Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Metal Grease Fil.
3 Installation • Any installation work must be undertaken by a qualified electrician or competent person. • This hood must be installed in accordance with the installation instructions and all measurements adhered to.
4 YOUR APPLIANCE OPERA TING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam . T o obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing.
5 This cooker hood can be used to recirculate or extract contaminated air . Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and than back into the kitchen.
6 MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . The cooker hood must be kept clean, a build up of grease or fat can be a fire hazard. External Cleaning The metal casing, grille and chimney should be cleaned at least once a month to keep it looking like new .
7 T o Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove. This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Worktop Lighting The lamps should be replaced with a 220-240V 20W halogen spot lamp.
8 SOMETHING NOT WORKING SER VICE AND SP ARE P ARTS If, having followed these instructions carefully , your cooker hood fails to work properly please carry out the following checks.
9 GUARANTEE CONDITIONS Standard Guarantee Conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG built-in appliance or any part thereof is proved to be defective b.
10 INST ALLA TION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way . T echnical Information DIMENSIONS HEIGHT (CANOPY): 73 mm HEIGHT (CHIMNEY): 450-850 mm WIDTH (CANOPY): 898 mm WIDTH (CHIMNEY): Ø200-Ø270 mm GROSS: 24.
11 INST ALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air .
12 A: Built-in Electric Hob: 650mm minimum clearance B: Built-in Gas hob: 700mm minimum clearance C: Slot-in Electric Cooker: 685mm minimum clearance D: Slot-in Gas Cooker: 787mm minimum clearance Hob.
13 Fixing the Chimney to the Canopy 1 . Remove the metal grease filter cassette by pushing inwardly on the two steel handles. 2. T o remove the charcoal filter push inwardly on the two retaining clips to disengage the security fixing and remove. 3. Align the fixing points on the chimney with the corresponding fixing points on the canopy .
14 3. Slide the chimney through the hole in the shelf before fixing it to the canopy . T op Shelf The top shelf only requires drilling if the hood is to be installed with the air outlet turned upwards. 1. Use the cardboard template provided to mark the hole position on the shelf.
15 5. Fix the round eyelet screws provided tightly into the holes (1). 6. Fix bracket (S) to the fan assembly . 7. The hood is supplied in the recirculation mode, with the recirculation grille (G) fitted over the outlet in the top of the fan assembly ready for use.
16 5. Mark the position on the wall and drill the hole for the ducting. T o calculate the centre of the hole on the wall for the ducting, draw a horizontal line (D) through the vertical line 80mm above line (X) The round ducting to be used must be Ø125mm.
17 4. Using a 8mm masonry bit, drill the holes for the canopy and fan assembly and insert the rawl plugs ready for the fixing screws. 5. The hood is supplied with the air outlet facing the rear .
18 Final fixing and adjustment of the hood: T wo adjustable connectors are provided at the rear of the hood. (a) T urn the screws (V1), until the screws (V2) align with the screw holes (F2). (b) Adjust the vertical and horizontal alignment using screws (V2).
19 Electrical connection and working test: 1. Remove the metal cover by unscrewing the four self tapping screws. 2. Connect the ‘Push-Fit’ connectors coming from the fan assembly to the canopy . 3. Position the terminals as illustrated under the cover and replace the cover with the four self tapping screws.
4329477 01 - 001013.
デバイスAEG 2020 Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
AEG 2020 Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAEG 2020 Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AEG 2020 Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AEG 2020 Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AEG 2020 Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAEG 2020 Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AEG 2020 Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAEG 2020 Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
