CanonメーカーL1000の使用説明書/サービス説明書
ページ先へ移動 of 610
REVISION 0 F AX-L1000 H12-1613 230V EC F AX-L1000 H12-1614 230V UK F AX-L1000 H12-1615 230V GER F AX-L1000 H12-1617 230V FRN F AX-L1000 H12-1618 230V AUS F AX-L1000 H12-1619 230V AE OPTION MEMOR Y VII.
Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory , installation, maintenance, and repair of products. This manual co vers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality .
I I. MEANINGS OF MARKS The marks used in this manual have the following meanings. Mark Meaning Indicates a general caution or warning, or otherwise to communicate the presence of a hazard. W arns of the possibility of an electric shock. Informs you of fire-related cautions.
II II. ABOUT THIS MANU A L This manual consists of the following five chapters, each providing appropriate information needed to service the product. Chapter 1: Safety and Precautions Provides cautions and w arnings needed when servicing the product while ensuring safety , and explains the protective functions built into the product.
III III. REVISION HIST OR Y REVISION CONTENT 0 Original.
IV IV . T ABLE OF CONTENTS Chapter 1: Safety and Precautions Page 1 - 1 1. D ANGER T O PERSONNEL 1 - 1 1.1 Electric Shock 1 - 2 1.1.1 A C line (A C 230V household current) 1 - 2 1.1.2 T elephone line 1 - 2 1.1.3 Printer high voltage terminal 1 - 3 1.2 High T emperature P ar ts 1 - 4 1.
V Chapter 2: Operating Instructions 2 - 1 1. NAMES OF P ARTS AND THEIR FUNCTIONS 2 - 1 1.1 Main Unit Overview 2 - 4 1.2 Operation Panel 2 - 7 2. BASIC OPERA TION 2 - 7 2.1 Copying 2 - 8 2.2 T elephone (Only possib le where a handset or telephone are connected) 2 - 9 2.
VI 3 - 18 2.1.2 Option overview 3 - 19 2.1.3 Consumables 3 - 21 2.2 Mechanical Overview 3 - 21 2.2.1 Unit layout diagrams 3 - 21 2.2.2 Document and recording paper flow 3 - 23 2.2.3 Drive system layout 3 - 25 2.2.4 Electrical system layout 3 - 30 2.3 Scanner Section 3 - 30 2.
VII 4 - 7 2. CONSUMABLES REPLACEMENT 4 - 7 2.1 T oner Car tr idge 4 - 7 2.2 Recording Paper 4 - 8 2.3 Stamp Ink 4 - 1 1 3. CLEANING 4 - 1 1 3.1 Main Unit 4 - 11 3.2 Document Pick-up Roller 4 - 11 3.3 Separation Roller (Upper) 4 - 11 3.4 Separation Roller (Lower) 4 - 11 3.
VIII 5 - 43 2. SER VICE T OOLS 5 - 43 2.1 Printer Dr iver T ester 5 - 43 2.1.1 Outline 5 - 44 2.1.2 Explanation of LEDs and Switches 5 - 45 2.1.3. Operation 5 - 51 3. OPTION 5 - 51 3.1 Option Memory VII (4M-BYTE) 5 - 51 3.1.1 Safety and precautions 5 - 51 3.
IX 5 - 209 3.8.2 Service operations 5 - 214 3.8.3 T echnical Information 5 - 214 3.8.4 Maintenance and service 5 - 215 3.9 RAM DIMM Module 5 - 215 3.9.1 Safety and precautions 5 - 215 3.9.2 Service operations 5 - 217 3.9.3 T echnical informations 5 - 218 3.
X V . ILLUSTRA TION INDEX Chapter 1: Safety and Precautions Page 1 - 2 Figure 1 - 1 Printer High V oltage T er minal 1 - 3 Figure 1 - 2 High T emperature P ar ts 1 - 7 Figure 1 - 3 Moving and Rotating.
XI 2 - 35 Figure 2 - 29 User Menu Settings (10/13) 2 - 36 Figure 2 - 30 User Menu Settings (11/13) 2 - 37 Figure 2 - 31 User Menu Settings (12/13) 2 - 38 Figure 2 - 32 User Menu Settings (13/13) 2 - 4.
XII 3 - 54 Figure 3 - 24 Drum Cleaning 3 - 55 Figure 3 - 25 High V oltage T er minals 3 - 56 Figure 3 - 26 T ransf er 3 - 56 Figure 3 - 27 Separation 3 - 57 Figure 3 - 28 Fixing section 3 - 60 Figure .
XIII 4 - 19 Figure 4 - 16 Cleaning Location 2 4 - 20 Figure 4 - 17 Preparation for Cleaning 1 4 - 20 Figure 4 - 18 Preparation for Cleaning 2 4 - 21 Figure 4 - 19 Cleaning Location 1 4 - 21 Figure 4 -.
XIV 5 - 61 Figure 5 - 14 Exter nal View 5 - 61 Figure 5 - 15 Attachment to the Main Unit 1 5 - 62 Figure 5 - 16 Attachment to the Main Unit 2 5 - 62 Figure 5 - 17 Attachment to the Main Unit 3 5 - 63 .
XV 5 - 144 Figure 5 - 64 System Data List (7/10) 5 - 145 Figure 5 - 65 System Data List (8/10) 5 - 146 Figure 5 - 66 System Data List (9/10) 5 - 147 Figure 5 - 67 System Data List (10/10) 5 - 148 Figu.
This page intentionally left blank.
Chapter 1 Saf ety and Precautions.
.
1-1 F AX-L1000 Chapter 1: Safety and Precautions 1. D ANGER T O PERSONNEL 1.1 Electric Shock Precautions Before disassembling the fax, carry out the following to prevent electric shock: (1) Disconnect the power cord from the outlet. (2) Disconnect the modular jack cord (telephone line) from the fax.
1-2 F AX-L1000 Chapter 1: Safety and Precautions 1.1.1 A C line (A C 230V household current) Power supply unit (primary side) The A C 230V is supplied to the primary side of the power supply unit when the po wer cord is plugged in. 1.1.2 T elephone line NCU board (primary side) When connected to the telephone line, a line voltage of approx.
1-3 F AX-L1000 Chapter 1: Safety and Precautions 1.2 High T emperature P arts Precautions T o prev ent b urns while disassembling the fax, disconnect the po w er cord at least 10 minutes before starting disassembly , to allow high temperature parts to cool down.
1-4 F AX-L1000 Chapter 1: Safety and Precautions 1.3 Fire Danger Do not throw the lithium battery or the toner cartridge into fire. Lithium battery The lithium battery contain lithium, organic solv ents and other comb ustible substances. If the lithium battery is thrown into fires, it may rupture and burn fiercely .
1-5 F AX-L1000 Chapter 1: Safety and Precautions This page intentionally left blank.
1-6 F AX-L1000 Chapter 1: Safety and Precautions 1.4 Moving and Rotating Parts Precautions T o prev ent accidents in volving mo ving or rotating parts during servicing, that disconnect the po wer cord before starting disassembly .
1-7 F AX-L1000 Chapter 1: Safety and Precautions Figure 1-3 Mo ving and Rotating Parts DC motor Pick-up roller Multi-pur pose tra y pickup roller Main motor Read motor Pressure roller Cassette pickup .
1-8 F AX-L1000 Chapter 1: Safety and Precautions 1.5 Laser Beams This fax is a Class 1 Laser Product as defined in the EN60825 (IEC825) Radiation Safety of laser products, equipment classif ication, requirements and user’ s guide.
1-9 F AX-L1000 Chapter 1: Safety and Precautions Figure 1-5 Laser Shutter Laser light Laser shutter Laser/Scanner unit FX6 toner car tr idge.
1-10 F AX-L1000 Chapter 1: Safety and Precautions 2. D ANGER T O EQUIPMENT 2.1 Handling the F AX Figure 1-6 Pr ecautions 1 General Precautions ❏ TO A VOID SERIOUS INJUR Y , NEVER DISASSEMBLE THE F AX. EXPOSED POWER POINTS INSIDE THE F AX CAN CAUSE ELECTRICAL SHOCK IF YOU TOUCH THEM.
1-11 F AX-L1000 Chapter 1: Safety and Precautions Figure 1-7 Pr ecautions 2 ❏ Before you transport the fax, r emove the cartridge. T o protect the cartridge fr om bright light, cover it with its original protective bag or a cloth. ❏ Keep liquids, cleaners, and other solvents away from the fax unit.
1-12 F AX-L1000 Chapter 1: Safety and Precautions 2.2 Storage and Handling of FX6 T oner Car tridge Whether the cartridge is still sealed in its box or installed in the printer , the effect of the natural en vironment will change it over time re gardless of the number of prints.
1-13 F AX-L1000 Chapter 1: Safety and Precautions 2.2.2 Storing unsealed parts As an organic photoconductor (OPC) is used in the photosensiti ve drum, it will deteriorate if exposed to strong light. As there is also toner in the cartridge, be sure to explain to the customer the need to be careful in handling and storing unsealed cartridges.
1-14 F AX-L1000 Chapter 1: Safety and Precautions After loading the cartridge in the printer , pr int 3 to 5 sheets of test patterns and check for toner leakage to prevent output image from dirt. (2) Remove the cartridge from the printer before transporting it.
1-15 F AX-L1000 Chapter 1: Safety and Precautions 2.3 Precautions when Servicing 2.3.1 Damage due to electrostatic discharge This fax contains contact sensor and printed circuit boards that use many electrical components such as R OM, RAM and custom ICs.
1-16 F AX-L1000 Chapter 1: Safety and Precautions 2.3.2 Lubrication points Do not touch the greased parts. If you do, the grease (applied for smooth operation of the printer mechanism and to increase electrical conductivity) will come of f. Use only specified grease.
1-17 F AX-L1000 Chapter 1: Safety and Precautions Fixing film T ransf er charging charging roller 2.3.4 Printer section a) T ransfer charging roller If skin, oil or , the like, gets on the rubber section of the transfer c harging roller , the rear side of the recording paper can be soiled, and blank patches can occur in printing.
1-18 F AX-L1000 Chapter 1: Safety and Precautions 2.3.5 P aper load section a) Pickup Roller Position When having assembled the paper pickup roller after parts replacement, before setting the cassette.
1-19 F AX-L1000 Chapter 1: Safety and Precautions 2.3.6 Control boards a) SCNT board Jumper plug JP3 and J6 are for factory check only . Service technician must not remo v e it. REFERENCE SCNT board data User data, service data are stored in memory on the SCNT board.
1-20 F AX-L1000 Chapter 1: Safety and Precautions 2.3.7 Replacing ROM Observe the following precautions when replacing the ROM on the SCNT board, for example, when replacing a defective ROM or when upgrading the software. a) Preparation Print out all battery backed up data.
1-21 F AX-L1000 Chapter 1: Safety and Precautions 3. PRECA UTIONS FOR D A T A PRO TECTION 3.1 Battery-backed up Data The SCNT board is provided with a function for backing up data in control processin.
1-22 F AX-L1000 Chapter 1: Safety and Precautions 3.2 Backed up by Rechargeable Battery The data stored in the image memory on the SCNT board is backed up for about 12 hours by the secondary v anadium-lithium battery .
1-23 F AX-L1000 Chapter 1: Safety and Precautions REFERENCE For a sample printout of the memory clear list, see Chapter 2, 3.1 Report Output Function . 3.2.2 Reception image data transfer The received image data cannot be printed out due to printer engine trouble, the received image data can be transferred to another fax and printed.
1-24 F AX-L1000 Chapter 1: Safety and Precautions 3.3 Backed up by Lithium Battery The lithium battery backs up control data registered in the SRAM on the SCNT board for five years with the po wer turned of f.
1-25 F AX-L1000 Chapter 1: Safety and Precautions c) Management data Data automatically stored as a record of the operating status. Item Description Activity report T ransmission/Reception records for last 40 communications System dump list A record of past communication conditions, error communication, etc.
1-26 F AX-L1000 Chapter 1: Safety and Precautions 3.3.2 Printing the lithium battery backup data list The following data are backed up by lithium battery and can be printed out as a list.
1-27 F AX-L1000 Chapter 1: Safety and Precautions Jumper plug caution The lithium battery backup function works when jumper plug JP 2 on the SCNT board is shorted by a jumper plug. This means that re gistered data will be erased when the power cord is disconnected with the jumper plug removed.
1-28 F AX-L1000 Chapter 1: Safety and Precautions 3.4 Data clear/initialization using Service Operation This fax can clear/initialize individual data items with Service Data #8 Clear operation. Below are the data items which can be cleared/initialized.
1-29 F AX-L1000 Chapter 1: Safety and Precautions 3.5 Master Password This fax has a password for confidential box setting changes and deletions, and passwords for managing each department. For service operations and for when the user for gets a password, there is a master password.
1-30 F AX-L1000 Chapter 1: Safety and Precautions 3.6 What to do when a Problem Occurs (All clear) V ery rarely , during use, the display may go out, all the b uttons may stop working, or some other trouble may occur because of strong electrical noise or strong shock.
1-31 F AX-L1000 Chapter 1: Safety and Precautions 4. PROTECTIVE FUNCTIONS 4.1 Reception Image Data T ransfer Function Reception image data can be transferred to another fax if the image data cannot be printed out due to printer engine trouble. REFERENCE Reception image data transfer For details on the transfer of image data, see this Chapter , 3.
1-32 F AX-L1000 Chapter 1: Safety and Precautions 4.3 Built-in Safety Measures 4.3.1 Overcurrent protection This fax is provided with an overcurrent protection circuit with built-in current fuse and t.
1-33 F AX-L1000 Chapter 1: Safety and Precautions 4.3.3 Power leakage protection The A C line, telephone line and metal parts of this fax ar e completely insulated. This f ax provides a grounding type (three-wire) power supply cable to prevent electrical shock.
1-34 F AX-L1000 Chapter 1: Safety and Precautions 5 . QU ALIFICA TION REQUIRED FOR INST ALLA TION W ORK The qualifications for installation must satisfy local laws and regulations.
Chapter 2 Operating Instructions.
.
2-1 F AX-L1000 Chapter 2: Operating Instructions 1. NAMES OF P AR TS AND THEIR FUNCTIONS 1.1 Main Unit Overview Figure 2-1 Fr ont V iew NO TE This fax does not have a power switch. DOCUMENT EXTENSION TRA Y Open to support long documents during scanning.
2-2 F AX-L1000 Chapter 2: Operating Instructions Figure 2-2 Rear V iew F ACE-UP TR A Y Holds printed documents after they are ejected from the fax. POWER SOCKET Connect the power cord here. LIFTING HANDLE Grip the fax here and on the opposite side to lift the fax unit.
2-3 F AX-L1000 Chapter 2: Operating Instructions This page intentionally left blank.
2-4 F AX-L1000 Chapter 2: Operating Instructions 1.2 Operation Panel Figure 2-3 Operation P anel 1 Go Ultra Fine Resolution Shift Menu Item V alue Enter/Cancel Energy Sav er Change Car tridge Rec.
2-5 F AX-L1000 Chapter 2: Operating Instructions Figure 2-4 Operation P anel 2 Energy Saver Switches the fax out of the energy saver mode. PRT . Message Switches the LCD display between the fax messages and the printer messages. Manual RX Switches the fax between the auto and manual receive mode.
2-6 F AX-L1000 Chapter 2: Operating Instructions Data Registration Dela yed T ransmission Memory Reception Memory Reference Confidential Mailbox Rela y Broadcast P olling T ransfer Report Memory Box Stamp(Option) P ause T one/ M D .T . Space TTI Selector Subaddress P ass word Delete A TT A CH THE M LABEL (SUPPLIED) FOR USE IN THE U .
2-7 F AX-L1000 Chapter 2: Operating Instructions 2. B ASIC OPERA TION 2.1 Copying (1) Set the recording paper NO TE Refer to Chapter 5, 1.4 Assemb ling the F ax, Loading P aper in Paper cassettes 1 and 2 for the method of setting the recording paper .
2-8 F AX-L1000 Chapter 2: Operating Instructions Figure 2-7 Document Guides Adjustment Figure 2-8 Document Load Limit 2.2 T elephone (Only possib le where a handset or telephone are connected) (1) Lift the handset or telephone receiv er . The sound of dial tone will be heard.
2-9 F AX-L1000 Chapter 2: Operating Instructions 2.3 T ransmission There are two ways to transmit the document: memory transmission and direct transmission. a) Memory transmission The set document is read into memory and then transmitted. Setting method Press the Direct TX button to turn of f the Direct TX LED.
2-10 F AX-L1000 Chapter 2: Operating Instructions 2.4 Reception There are 3 reception methods: auto reception, manual reception, and auto reception switching. a) A uto reception This is set when the machine is used exclusi vely for facsimile. The initial condition of the machine is set to “Auto reception”.
2-11 F AX-L1000 Chapter 2: Operating Instructions 3. SER VICE OPERA TION FUNCTIONS 3.1 Report Output Function 3.1.1 User report output functions This fax can output user reports manually by user operation, or automatically , according to user data registration.
2-12 F AX-L1000 Chapter 2: Operating Instructions c) Reports output automatically (Memory clear report) When this fax is turned on and the memory clear report is automatically printed out, the image data which appears on the report is the data which was deleted without being able to be backed up.
2-13 F AX-L1000 Chapter 2: Operating Instructions 3.1.2 Service report output functions This fax outputs the service data setting status, past communications history reports, detailed error information reports, etc. in service mode. a) List of service reports This fax outputs the service reports sho wn belo w .
2-14 F AX-L1000 Chapter 2: Operating Instructions a-1) System data list This list sho ws service data setting statuses of service soft switches and service parameters.
2-15 F AX-L1000 Chapter 2: Operating Instructions Figure 2-11 System Data List (2/7).
2-16 F AX-L1000 Chapter 2: Operating Instructions Figure 2-12 System Data List (3/7).
2-17 F AX-L1000 Chapter 2: Operating Instructions Figure 2-13 System Data List (4/7).
2-18 F AX-L1000 Chapter 2: Operating Instructions Figure 2-14 System Data List (5/7).
2-19 F AX-L1000 Chapter 2: Operating Instructions Figure 2-15 System Data List (6/7).
2-20 F AX-L1000 Chapter 2: Operating Instructions Figure 2-16 System Data List (7/7) NO TE “ ST AR T D A TE ” records the date when this fax performs its first transmission or reception, after shipment from the factory .
2-21 F AX-L1000 Chapter 2: Operating Instructions a-2) System dump list This list sho ws the past communications statuses and error communications history .
2-22 F AX-L1000 Chapter 2: Operating Instructions *1 : Date on w hich data was initialized with service data #8 CLEAR , ALL *2 : T otal number of transmission *3 : T otal number of pages transmitted f.
2-23 F AX-L1000 Chapter 2: Operating Instructions Displays err or information f or the 3 most recent communications. Figure 2-18 System Dump List (2/2) *1 : Service error code *2 : Communication start date and time (on 24-hour display) *3 : T elephone number sent from other party *4 : Maker code *5 : Machine code *6 : Receiv ed V .
2-24 F AX-L1000 Chapter 2: Operating Instructions a-3) Service activity report The ERROR TX REPORT includes appended service error codes and an error dump list.
2-25 F AX-L1000 Chapter 2: Operating Instructions *1 : OK, NG messages *2 : Indicates four digits of the transaction number *3 : Number sent from the other party or number dialled (lower 20 digits) *4.
2-26 F AX-L1000 Chapter 2: Operating Instructions 3.2 User Data Flowchart Press the Data registration to access User menu. Figures in boldface indicate the default setting. Figure 2-20 User Menu Settings (1/13) 1. D A T A REGISTRA TION 1.USER SETTINGS 1.
2-27 F AX-L1000 Chapter 2: Operating Instructions Figure 2-21 User Menu Settings (2/13) 2. REPORT SETTINGS 1. TX REPORT 2. RX REPORT 3. CONFID . RX REPORT 4. MEMOR Y BO X REPOR T 5. ACTIVITY REPOR T 6.PR T REPOR T WHERE PRINT ERROR ONL Y OUTPUT YES OUTPUT NO REPOR T WITH TX IMAGE PRINT ERROR ONL Y OUTPUT YES OUTPUT NO OUTPUT YES OUTPUT NO 1.
2-28 F AX-L1000 Chapter 2: Operating Instructions Figure 2-22 User Menu Settings (3/13) 1. ECM TX 2. MID P A USE SET * 1 (2.) TRANSMISSION MODEL * 2 3. A UT O REDIAL 4. BA TCH TX 5. QUICK ON-LINE TX * 5 6. TIME OUT (7.) TX ST AMP (7.) ST ART UP DIAL KEY (8.
2-29 F AX-L1000 Chapter 2: Operating Instructions Figure 2-23 User Menu Settings (4/13) 1. USE MP TRA Y 2. # OF RX COPIES 3. SELECT CASSETTE 4. RX REDUCTION 5. SELECT DENSITY 6. TONER SUPPL Y LOW 7. SELECT OUTPUT TRA Y 5. F AX'S PRINTER SET 1. CASSETTE SW A 2.
2-30 F AX-L1000 Chapter 2: Operating Instructions Figure 2-24 User Menu Settings (5/13) 2. RELA Y TX GR OUP 1.SETUP FILE 2.CHANGE D A T A SET RL Y TX GROUP #00 (00~99) 1.GROUP DIAL NAME 2.P ASSWORD 3.SUBADDRESS (INPUT) 4.RX P ASSWORD (INPUT) 5.SELECT ORIG UNIT 6.
2-31 F AX-L1000 Chapter 2: Operating Instructions Figure 2-25 User Menu Settings (6/13) 3. MEMOR Y BO X 1.SETUP FILE (00~99) SET BO X # 00 1.FILE NAME 2.P ASSWORD 3.SUBADDRESS 4.TX P ASSWORD 5.RX P ASSWORD 6.RECEIVE 7.TRANSMIT YES NO 1.SELECT ORIG UNIT 2.
2-32 F AX-L1000 Chapter 2: Operating Instructions Figure 2-26 User Menu Settings (7/13) 2.CHANGE DA T A SET BO X #00 (00~99) P ASSW ORD (INPUT) 1.FILE NAME 2.P ASSW ORD 3.SUBADDRESS 4.TX P ASSW ORD 5.RX P ASSW ORD 6.RECEIVE 7.TRANSMIT YES NO 1.SELECT ORIG UNIT 2.
2-33 F AX-L1000 Chapter 2: Operating Instructions Figure 2-27 User Menu Settings (8/13) 4. PRESET POLLING 1.SETUP FILE 2.CHANGE D A T A 3.DELETE FILE 1.FILE NAME 2.P ASSW ORD 3.SELECT LOCA TIONS 4.ST ART TIME P ASSW ORD (INPUT) 1.FILE NAME 2.P ASSW ORD 3.
2-34 F AX-L1000 Chapter 2: Operating Instructions Figure 2-28 User Menu Settings (9/13) 6. TRANSFER 1.SETUP FILE 1.FILE NAME 2.SELECT LOCA TIONS 3.P ASSW ORD 4.SELECT ORIG UNIT 5.TIME SETUP TEL = OFF ON TEL = 1.ST ART TIME EVERYD A Y SELECT D A YS (5 time settings) 1.
2-35 F AX-L1000 Chapter 2: Operating Instructions Figure 2-29 User Menu Settings (10/13) 7. SYSTEM SETTINGS (0000~9999) 1. TX SETTINGS ON OFF D A C SETUP ON OFF ENTER D A C (19 settings input) P ASSWORD (INPUT) USER A CCESS CODE CODE (INPUT) 2. F AX'S PRINTER SET ON OFF USER A CCESS CODE CODE (INPUT) 1.
2-36 F AX-L1000 Chapter 2: Operating Instructions Figure 2-30 User Menu Settings (11/13) 4.RX RESTRICTION ON OFF MM/DD/YYYY DD/MM YYYY YYYY MM/DD ENGLISH FRENCH SP ANISH GERMAN IT ALIAN DUTCH FINNISH PORTUGUESE NORWEGIAN SWEDISH D ANISH SLO VENE 33600bps 14400bps 9600bps 7200bps 4800bps 2400bps 5.
2-37 F AX-L1000 Chapter 2: Operating Instructions Figure 2-31 User Menu Settings (12/13) 2. TEL REGISTRA TION 1. TELEPHONE NUMBER 2. NAME 3. OPTIONAL SETTING 1. 1-TOUCH SPD DIAL (01~72) ON OFF (5 time settings) REGULAR TX CONFIDENTIAL TX ORIG RELA Y TX PSWD/SUBADDRESS POLLING RX 1.
2-38 F AX-L1000 Chapter 2: Operating Instructions Figure 2-32 User Menu Settings (13/13) 1. TELEPHONE NUMBER 2. NAME 3. OPTIONAL SETTING (5 time settings) 2. CODED SPD DIAL ( ✶ 000~ ✶ 127) REGULAR TX CONFIDENTIAL TX ORIG RELA Y TX PSWD/SUBADDRESS POLLING RX 3.
2-39 F AX-L1000 Chapter 2: Operating Instructions 3.3 Service Switches 3.3.1 Har dware s witches This fax has the following hardware switches. a) SCNT board Jumper s witch (JP1) The secondary v anadium-lithium battery backs up image memory by causing a short with the jumper plug.
2-40 F AX-L1000 Chapter 2: Operating Instructions e) NCU board There are three slide switches on the NCU board. Figure 2-33 Slide Switch Location on NCU Board Figure 2-34 Slide Switch Setting NO TE NCU Board Switch Setting This model has only one connection terminal for extension telephone/handset.
2-41 F AX-L1000 Chapter 2: Operating Instructions 3.3.2 Service data setting Service data can be checked and changed with items on display menus. The ef fecti ve SSSWs/ parameters and their default v alues in this fax machine are sho wn in 3.3.4 Ser vice data flowchar t in this chapter .
2-42 F AX-L1000 Chapter 2: Operating Instructions #8 CLEAR (data initialization mode) V arious data are initialized by selecting one of these setting items. There is a setting item for checking/inputting the total number of pages printed and total number of pages scanned by this fax.
2-43 F AX-L1000 Chapter 2: Operating Instructions 3.3.4 Service data flowchar t Figure 2-36 Service Data (1/6) The switches marked “–” are not used.
2-44 F AX-L1000 Chapter 2: Operating Instructions Figure 2-37 Service Data (2/6) No. 001 to 004, 011 to 020 are not used. Do not change their settings.
2-45 F AX-L1000 Chapter 2: Operating Instructions Figure 2-38 Service Data (3/6) No. 001, 005 to 008, 012, 014, and 016 to 080 are not used. Do not change their settings #3 NUMERIC P aram.
2-46 F AX-L1000 Chapter 2: Operating Instructions #4B NCU * 1 TONE/PULSE (NCU settings) DIAL TONE 2nd DIAL TONE BUSY T ONE 0 BUSY T ONE 1 REORDER TONE MUL TI AU T O R X CNG DETECT RKEY PBX DIAL TONE P.
2-47 F AX-L1000 Chapter 2: Operating Instructions Figure 2-40 Service Data (5/6) #4A SPECIAL, #4B NCU The v alues of these items are all set to match a specific nation’ s communications standards by the #5 TYPE setting. Do not change these settings.
2-48 F AX-L1000 Chapter 2: Operating Instructions Figure 2-41 Service Data (6/6) REFERENCE For details on test mode, see this Chapter , 3.4 T est Functions .
2-49 F AX-L1000 Chapter 2: Operating Instructions 3.3.5 Explanation of SSSW (Service Soft Switch Settings) The items registered and set by each of these switches comprise 8-bit switches. The figure belo w sho ws which numbers are assigned to which bits.
2-50 F AX-L1000 Chapter 2: Operating Instructions 3.3.6 New SSSWs/parameter s added to this model #1 SSSW SW01 (service soft switch 01: err or management ) Bit Function 1 0 0 Ser vice error code Outpu.
2-51 F AX-L1000 Chapter 2: Operating Instructions #1 SSSW SW05 (service soft switch 05: standard function <DIS signal> settings) Bit Function 1 0 0 Not used 1 Not used 2 Not used 3 Send DIS sign.
2-52 F AX-L1000 Chapter 2: Operating Instructions #1 SSSW SW06 (service soft switch 06: scan condition settings) Bit Function 1 0 0 Document f eed after DES on No feed Feed 1 Prescan f or document scanning No prescan Prescan 2 Document length restriction Not restricted 39.
2-53 F AX-L1000 Chapter 2: Operating Instructions #1 SSSW SW26 (service soft switch 26: transmission function settings) Bit Function 1 0 0 Compulsor y direct transmission Set Not set function 1 Not us.
2-54 F AX-L1000 Chapter 2: Operating Instructions #1 SSSW SW28 (service soft switch 28: V .8/V .34 protocol settings) Bit Function 1 0 0 (New) Caller V .8 protocol NO YES 1 (New) Called par ty V .8 protocol NO YES 2 (Ne w) Caller V .8 protocol late star t NO YES 3 (Ne w) Called par ty V .
2-55 F AX-L1000 Chapter 2: Operating Instructions #2 MENU No. Function Selection range Default setting 008 V .34 max. baud rate 2400~3429 3429 (3429 baud) 009 V .34 max. transmission speed 2.4~33.6 33.6 (33600 bps) [No. 008] Select the maximum baud rate for V .
2-56 F AX-L1000 Chapter 2: Operating Instructions #3 NUMERIC P ARAM. (numeric parameter settings) No. Function Selection range Default setting 010 T0 Timer 0 ~ 9999 5500 (55 second) 011 T1 Timer (Rx) 0 ~ 9999 3500 (35 second) 013 Maximum time to receive 500 ~ 3000 1320 (13.
2-57 F AX-L1000 Chapter 2: Operating Instructions #7 PRINTER Service soft switch settings SW04 (switc h 04: reduction/cassette selection settings) Bit Function 1 0 0 (Ne w) When L TR/LGL specification No Ye s is receiv ed by DCS , the cassette is selected according to the specification.
2-58 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE EUROPE U.K. SWEDEN SWISS A USTRIA DENMARK #1 SSSW SW01 00010000 00010000 00010000 00010000 00010000 00010000 SW02 00000000 0.
2-59 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE NOR W A Y HOLLAND BELGIUM A USTRALIA FINLAND N.Z. #1 SSSW SW01 00010000 00010000 00010000 00010000 00010001 00010000 SW02 00.
2-60 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE IT AL Y SP AIN PORTUGAL IRELAND HUNGAR Y SAF #1 SSSW SW01 00010000 00010000 00010000 00010000 00010000 00010000 SW02 0000000.
2-61 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE GERMAN FRANCE CZECH SLO VENIA #1 SSSW SW01 00010000 00010000 00010000 00010000 SW02 00000000 00000000 00000000 00000000 SW03.
2-62 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE EUROPE U.K. SWEDEN SWISS A USTRIA DENMARK #3 NUMERIC P aram 02: 10 10 10 10 10 10 03: 15 15 15 15 15 15 04: 12 12 12 12 12 1.
2-63 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE NOR W A Y HOLLAND BELGIUM A USTRALIA FINLAND N.Z. #3 NUMERIC P aram 02: 10 10 10 10 10 10 03: 15 15 15 15 15 15 04: 12 12 12.
2-64 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE IT AL Y SP AIN PORTUGAL IRELAND HUNGAR Y SAF #3 NUMERIC P aram 02: 10 10 10 10 10 10 03: 15 15 15 15 15 15 04: 12 12 12 12 1.
2-65 F AX-L1000 Chapter 2: Operating Instructions SSSW Default Setting TYPE GERMAN FRANCE CZECH SLO VENIA #3 NUMERIC P aram 02: 8 8 10 10 03: 15 15 15 15 0 4 : 6 1 21 21 2 0 5 : 4444 0 6 : 4444 0 9 : .
2-66 F AX-L1000 Chapter 2: Operating Instructions 3.4 T est Functions This fax functions for testing indi vidual operations, such as belo w . 3.4.1 T est mode overview T est mode can be executed by follo wing the menu items from the display . a) DRAM tests Writes data to DRAM image storage areas and reads that data to check operations.
2-67 F AX-L1000 Chapter 2: Operating Instructions 3.4.2 T est mode flowchart T o operate the test mode, after pressing the Data registration button, press the # b utton and select “ SER VICE MODE ”. After this, select “ TEST MODE ” with the ▲ ▼ buttons, and press the Set button.
2-68 F AX-L1000 Chapter 2: Operating Instructions Figure 2-45 T est Mode (2/2) [9]ISDN TEST [1] DRAM TEST [2] FREQ [3] LOOP TEST [4] G3 Tx TEST [7] V34 G3 Tx TEST [8] DTMF Tx TEST * (Indicated only when the optional F AX-L1000 ISDN kit is installed.
2-69 F AX-L1000 Chapter 2: Operating Instructions 3.4.3 D-RAM tests Pressing the numeric ke y 1 from the test mode menu selects the D-RAM tests. D-RAM T est 1 writes data to the entire D-RAM region and reads it out to check that operations are correct.
2-70 F AX-L1000 Chapter 2: Operating Instructions 3.4.4 Print test a) T est mode print test The Print T est menu is selected by pressing the numeric key 3 from the test mode menu.
2-71 F AX-L1000 Chapter 2: Operating Instructions 3.4.5 Modem and NCU tests These tests test modem and NCU transmission and reception. The modem tests check whether signals are sent correctly from the modem by comparing the sound of the signals from the speaker with the sounds from a normal modem.
2-72 F AX-L1000 Chapter 2: Operating Instructions b) G3 signal transmission test The G3 signal transmission test menu is selected by pressing the numeric ke y 4 from the MODEM NCU test menu. The G3 signals belo w are sent from the modem using the modular jack and the speaker .
2-73 F AX-L1000 Chapter 2: Operating Instructions c) T onal and DTMF signal reception tests The tonal and DTMF signal reception test is selected by pressing the numeric key 6 from the MODEM NCU test menu. In these tests, you can check whether the tonal signals and DTMF signals receiv ed from the modular jack are detected by the modem.
2-74 F AX-L1000 Chapter 2: Operating Instructions d) V .34 G3 signal transmission test The V .34 G3 signal transmission test menu is selected by pressing the numeric ke y 8 from the MODEM NCU test menu. The V .34 G3 signals below are sent from the modem using the modular jack and the speaker by pressing the Star t/Scan button.
2-75 F AX-L1000 Chapter 2: Operating Instructions 3.4.6 A GING test If the numeric ke y 5 is pressed in the test mode menu, the A GING test is selected. In this test, the contact sensor LED is lit, and the document read motor dri ven in f ine mode. Also, the printer will f ine print a endurance pattern.
2-76 F AX-L1000 Chapter 2: Operating Instructions 3.4.7 F aculty tests The faculty tests are selected by pressing the numeric ke y 6 from the test mode menu. These tests test the follo wing faculties of this fax. T est type Overview Sensor tests T est whether the sensors are operating correctly .
2-77 F AX-L1000 Chapter 2: Operating Instructions Figure 2-49 Sensor T ests NO TE The sensor test 4 to 6 are for factory testing purposes, and so are unrelated in the field.
2-78 F AX-L1000 Chapter 2: Operating Instructions a-1) T oner sensor test chec k method Use the following methods to test “TN on”, and “TN of”. • "TN on" check (1) Open the printer cov er . (2) Insert a cartridge containing toner into the fax.
2-79 F AX-L1000 Chapter 2: Operating Instructions (3) Close the printer cov er . If the printer cov er is closed without a cartridge being inserted, there will be no “TN of” display , and this will not count as a sensor malfunction.
2-80 F AX-L1000 Chapter 2: Operating Instructions c) Operation panel tests The operation panel test is selected by pressing the numeric ke y 7 from the faculty test menu. In this test, check that the display , LED lamps, b uttons and the sensors of one-touch speed dialing panel on the operation panel are operating correctly .
2-81 F AX-L1000 Chapter 2: Operating Instructions When all the characters displayed hav e gone out, the system next starts the one-touch speed dialing button test. The letters a to y are displayed, corresponding to one-touch speed dialing button 1 to 25 .
2-82 F AX-L1000 Chapter 2: Operating Instructions Figure 2-52 Operation Panel 6-7:OPERA TION P ANEL HHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHH 6-7:OPERA TION P ANEL LED TEST 123456789 ∗ 0# TR COD abcdefghijklmnopqrst uvwxyzAB Press Star t/Scan button.
2-83 F AX-L1000 Chapter 2: Operating Instructions 3.4.8 ISDN test When numeric ke y 9 is pressed on the TEST MODE menu, the ISDN test is selected. An ISDN test and a modem test are carried out.
2-84 F AX-L1000 Chapter 2: Operating Instructions c) G3 signal transmission test When numeric ke y 4 is pressed on the ISDN test menu, the G3 signal transmission test is selected. Press numeric ke y 1 or 2 to select one of two modems. This test sends a G3 signal from a modem with a speaker .
2-85 F AX-L1000 Chapter 2: Operating Instructions d) V .34 G3 signal transmission test The V .34 G3 signal transmission test menu is selected by pressing the numeric ke y 8 from the MODEM NCU test menu. The V .34 G3 signals below are sent from the modem using the modular jack and the speaker by pressing the Star t/Scan button.
2-86 F AX-L1000 Chapter 2: Operating Instructions This page intentionally left blank.
Chapter 3 T ec hnical Reference.
.
3-1 F AX-L1000 Chapter 3: T echnical Reference 1. SPECIFICA TIONS 1.1 Overview This G3 facsimile transceiver conforms to ITU-T international standards.
3-2 F AX-L1000 Chapter 3: T echnical Reference •Expanded transaction features Y ou can create up to 50 priv ate memory boxes and set them up to recei ve documents. If the other party’ s fax can use ITU-T subaddresses and passwords, you can set up and use memory boxes e ven if the other party’ s fax unit is not a Canon fax.
3-3 F AX-L1000 Chapter 3: T echnical Reference 1.2 Configuration and Structure 1.2.1 Product names LASER beam printing type G3 facsimile F AX-L1000 1.2.
3-4 F AX-L1000 Chapter 3: T echnical Reference 1.2.3 Configuration a) Main unit Structural section : Frame, motors, rollers, cov ers, and others (sensors, etc.
3-5 F AX-L1000 Chapter 3: T echnical Reference 1.3 Specifications and Functions 1.3.1 Basic specifications T ype Desktop facsimile transceiver Body color Art gray Power source V oltage from A C 180 to 264 V Frequency from 48 to 62 Hz Power consumption Standby (ESS On) approx.
3-6 F AX-L1000 Chapter 3: T echnical Reference 1.3.2 Communications specifications Applicable lines Analog line (one line) • PSTN (Public Switched T elephone Network) Handset (Option) Handset with no numeric buttons T ransmission method Half-duplex T ransmission control pr otocol ITU-T V .
3-7 F AX-L1000 Chapter 3: T echnical Reference Canon express protocol CEP1 Time required for transmission pr otocol Post-message Post-message Pre-message Protocol *2 Protocol *3 Mode Protocol *1 (between pages) (after pages) V .8 / V .34 Approx. 6 s Approx.
3-8 F AX-L1000 Chapter 3: T echnical Reference 1.3.3 Scanner section specifications T ype Sheets Sheet dimensions Maximum W idth 10.98" × length 39.4" (W idth 279mm × length 1m) Minimum W idth 5.83" × length 5.04" (W idth 148mm × length 128mm) Thickness Multiple pages from 0.
3-9 F AX-L1000 Chapter 3: T echnical Reference Copy resolution Memory copy 16 dots/mm × 15.4 line/mm (Interpolated) Scanning density adjustment Lighter , Standard, Darker: The density lev el of each mode can be selected by the user data. NO TE Scanning density adjustment is only valid in binary image mode.
3-10 F AX-L1000 Chapter 3: T echnical Reference Scanning range Item A4 Letter Legal B4 (AE only) Effecti ve 8.19"±0.004" 8.43"±0.004" 8.43"±0.004" 10.00"±0.004" scanning width (208 ±0.1 mm) (214 ±0.1 mm) (214 ±0.
3-11 F AX-L1000 Chapter 3: T echnical Reference 1.3.4 Printer section specifications Paper dimensions A4 8.27" × 11.69" (210 mm × 297 mm) Letter 8.50" × 10.98" (216 mm × 279 mm) Lega l 8.50" × 14.02" (216 mm × 356 mm) Paper cassette capacity Cassette 2.
3-12 F AX-L1000 Chapter 3: T echnical Reference Recommended recording paper Canon Copier L TR/LGL Premium Paper W eight 75 g/m 2 Paper size Letter , Legal Manufactured by BOISE CASCADE KANGAS W eight .
3-13 F AX-L1000 Chapter 3: T echnical Reference Printing range Item A4 Letter Legal Ef fecti ve printing width 8.01 8.24" 8.24" (203.5 mm) (209.4 mm) (209.4 mm) Ef fecti ve printing length 11.34" ±0.12" 10.65" ±0.12" 13.
3-14 F AX-L1000 Chapter 3: T echnical Reference 1.3.5 Functions F AX/TEL switching None Answering machine connection None Memory reception When recei ving Canon F AX Standard Chart No.1 Standard Max. 192 pages Memory expanded Max. 448 pages (4MB option memory mounted) Max.
3-15 F AX-L1000 Chapter 3: T echnical Reference Auto dialing T elephone number digits Max. 39 digits One-touch dial Max. 72 Coded speed dial Max. 128 Group dial Max. 199 (One-touch: 71, Coded speed dial: 128) Redial Numeric button redial function (max.
3-16 F AX-L1000 Chapter 3: T echnical Reference Activity management a) User report Activity management report (Every 40 transactions : Can be separated into Tx and Rx) Activity report (sending / recei.
3-17 F AX-L1000 Chapter 3: T echnical Reference Memory backup Backup contents Dial registration data, user data, service data, time Backup IC 512 kbit SRAM (256 kbit SRAM × 2) Backup battery Lithium battery 3.
3-18 F AX-L1000 Chapter 3: T echnical Reference 2. THEOR Y OF OPERA TIONS 2.1 Product Overview 2.1.1 Fax main unit This fax operates on ordinary A C230V household current, and has fax, tele phone, and copy functions. The communication functions include 33.
3-19 F AX-L1000 Chapter 3: T echnical Reference f) 4MB memory kit The image memory can be expanded by installing 4MB memory boards. T wo memory boards can be installed in the fax machine.
3-20 F AX-L1000 Chapter 3: T echnical Reference Figure 3-4 Pr oduct Ove rview Main unit F AX-L1000 Option OPTION MEMORY VII (4MB) Consumables FX6 toner car tridge P APER FEED UNIT PF-52 DUPLEX UNIT DU.
3-21 F AX-L1000 Chapter 3: T echnical Reference 2.2 Mechanical Overview The mechanical section of this fax comprises the scanner section, the pickup section, and the printer section.
3-22 F AX-L1000 Chapter 3: T echnical Reference Figure 3-5 P aper Path Document path Recording paper path Printer Section Scanner Section P aper pic kup Section.
3-23 F AX-L1000 Chapter 3: T echnical Reference 2.2.3 Drive system layout a) Scanner section The power of the document read motor is transmitted by belt and gear to drive the pick-up, separation, feed, and eject rollers. The rotation of pick-up roller is controlled by a cam, DC motor and separation roller arm.
3-24 F AX-L1000 Chapter 3: T echnical Reference Figure 3-6 Dri ve System Lay out DC motor Pick-up roller Multi-pur pose tra y pickup roller Main motor Read motor Pressure roller Cassette pickup roller.
3-25 F AX-L1000 Chapter 3: T echnical Reference 2.2.4 Electrical system layout a) Board layout a-1) SCNT board The SCNT board, which contains the system controller which controls the entire fax, is attached to the right side of the main unit.
3-26 F AX-L1000 Chapter 3: T echnical Reference Figure 3-7 Electrical System Lay out P aper siz e detection boards P aper size detection board 1 P aper size detection board 2 P ower supply unit OPCNT .
3-27 F AX-L1000 Chapter 3: T echnical Reference b) Sensor layout b-1) Contact sensor This contact sensor (CS) horizontally scans documents up to Letter size 8.42" (214mm) (B4 size 10.00" (254 mm) for AE) at a horizontal scanning resolution of 8 dots/mm.
3-28 F AX-L1000 Chapter 3: T echnical Reference b-12) Recording paper eject sensor 1 This sensor , which detects whether or not the recor ding paper has been fed as far as the fixing unit, is attached to the ECNT board.
3-29 F AX-L1000 Chapter 3: T echnical Reference Figure 3-8 Arrangement of Sensors Pre-feed sensor Printer cover sensor Document edge sensor Multi-purpose tray paper sensor T op of page sensor Cassette.
3-30 F AX-L1000 Chapter 3: T echnical Reference 2.3 Scanner Section The scanner section comprises the document feed section and the optical section. 2.
3-31 F AX-L1000 Chapter 3: T echnical Reference Figure 3-9 Document F eed Section Document path Separation roller(low er) Pick-up roller Separation roller(upper) Contact sensor Document f eed roller D.
3-32 F AX-L1000 Chapter 3: T echnical Reference NO TE Document stopper movement (1) When documents are set (Fig. A) The document stopper on the ADF section (Upper reader frame) stops the document which is inserted into the document insertion opening, pre venting it from being pushed in too f ar .
3-33 F AX-L1000 Chapter 3: T echnical Reference Figure 3-10 Stopper Mo vement (A) (B) (C) (D) (E).
3-34 F AX-L1000 Chapter 3: T echnical Reference b-2) Document jam detection The document edge sensor detects such document jams as pickup jams and document too long errors. A “pickup jam” means the document edge sensor cannot detect the leading edge of the document within 15 seconds after document feeding begins.
3-35 F AX-L1000 Chapter 3: T echnical Reference 2.3.2 Optical section a) Functions a-1) Document scanning For document scanning, the Contact Sensor (CS) horizontally scans documents up to L TR size 8.
3-36 F AX-L1000 Chapter 3: T echnical Reference b) Structures b-1) Contact sensor The contact sensor is designed to be dust-free, so that dust and other such minute particles cannot find their way inside the contact sensor housing, to settle on the sensor surface.
3-37 F AX-L1000 Chapter 3: T echnical Reference Figure 3-11 Contact Sensor Document Contact sensor logic board Photo transistor LED Scanning glass Incident light Contact sensor logic board LED Scannin.
3-38 F AX-L1000 Chapter 3: T echnical Reference 2.4 Paper Load Section a) Functions a-1) Recording paper pickup function (From multi-purpose tray) In case of paper pick-up from the multi-purpose tray , while the main motor rotates, the multi-purpose tray pick-up solenoid is turned ON.
3-39 F AX-L1000 Chapter 3: T echnical Reference b) Structures b-1) Cassette paper loading In case of paper pick-up from the cassette, while the main motor rotates, the pick-up solenoid (SL101) is turned ON. Then, cassette pick-up roller , cassette feed roller , separation roller and feed rollers rotate, and a sheet of paper is fed into the fax.
3-40 F AX-L1000 Chapter 3: T echnical Reference Figure 3-12 Cassette P aper Loading F eed roller F eed roller Separation roller P aper pickup roller Spring Lifting plate F eed roller Separation roller.
3-41 F AX-L1000 Chapter 3: T echnical Reference b-2) Recording paper pickup jam detection configuration Recording paper pickup jams are detected by the photo-interrupter type recording paper pickup sensor equipped with an actuator arm. There are the following two types of recording paper pickup jams.
3-42 F AX-L1000 Chapter 3: T echnical Reference b-3) No recording paper detection configuration The presence of paper on the multi-purpose tray is detected by the multi-purpose tray paper sensor (PS105).
3-43 F AX-L1000 Chapter 3: T echnical Reference Figure 3-13 Paper Size Detection Conf iguration (Paper feeder) Figure 3-14 Paper Size Detection Conf iguration (Option paper feed unit PF-52) P aper siz.
3-44 F AX-L1000 Chapter 3: T echnical Reference 2.5 Printer Section The LASER beam printer engine comprises the following sections. Figure 3-15 Printer Section Fixing unit F eed roller T oner car tr i.
3-45 F AX-L1000 Chapter 3: T echnical Reference 2.5.1 Paper feed/eject section a) Functions a-1) Paper feed/eject The feed section feeds the recording paper fed from the pickup section to the toner transfer section and fixing unit. The eject section ejects the paper from the recording paper eject outlet on the main unit after printing.
3-46 F AX-L1000 Chapter 3: T echnical Reference Figure 3-16 P aper F eed/Eject Section P aper path F eed roller ECNT board Photosenstiv e drum Pre-tr ansf er roller Pressure roller Fixing eject roller.
3-47 F AX-L1000 Chapter 3: T echnical Reference b-2) Recording paper jam detection configuration Recording paper jams in the paper feed/eject section are detected by the photo-interrupter type pre-feed sensor , top of page sensor , recording paper eject sensor 1 and 2, which is equipped with an actuator arm.
3-48 F AX-L1000 Chapter 3: T echnical Reference 2.5.2 LASER/Scanner section a) Functions Figure 3-17 LASER/Scanner Section The VIDEO signal (nVDO) is sent from the SCNT board to the laser dri ver of the laser/ scanner unit through the TWINS board and ECNT board.
3-49 F AX-L1000 Chapter 3: T echnical Reference b) A utomatic power contr ol of laser diode The laser driver IC conducts the automatic power control (APC) of the laser diode so that the laser diode emits a beam of constant intensity .
3-50 F AX-L1000 Chapter 3: T echnical Reference 2.5.3 T oner car tridg e a) Functions Figure 3-18 T oner Cartr idge The image formation system is the central hub of the fax, and consists of the photosensiti ve drum, dev eloping unit, charging rollers, etc.
3-51 F AX-L1000 Chapter 3: T echnical Reference b) Electrostatic latent image formation block This block follows two steps to produce an electrostatic latent image on the photosensitive drum.
3-52 F AX-L1000 Chapter 3: T echnical Reference b-2) Laser beam exposure Figure 3-21 Laser Beam Exposur e When the laser beam scans the drum surface, it causes the charges in the areas struck by the laser beam to be neutralized. These areas on the drum surface form the electrostatic latent image.
3-53 F AX-L1000 Chapter 3: T echnical Reference As shown in Figure 3-23, the developing unit consists of a fixed magnet, a developing cylinder and a rubber blade. The de v eloping cylinder rotates around the f ix ed imagnet. The single-component toner consists of magnetite and a resin binder , and is held to the cylinder by magnetic attraction.
3-54 F AX-L1000 Chapter 3: T echnical Reference d-1) Drum cleaning Figure 3-24 Drum Cleaning The residual toner on the drum surface is scraped away with the cleaner blade to clean the drum surface in preparation for the ne xt print. The remo v ed waste toner is collected into the waste toner case.
3-55 F AX-L1000 Chapter 3: T echnical Reference • The high-voltage terminal of the toner cartridge is sho wn belo w . Figure 3-25 High V oltage T erminals • The A C bias applied to the de v eloping cylinder during de velopment is about 1600 Vp-p.
3-56 F AX-L1000 Chapter 3: T echnical Reference 2.5.4 T ransfer/Separation section In this block, the toner image is transferred from the drum surface to the paper . a) T ransfer Figure 3-26 T ransfer Positi ve char ges are applied to the back of the paper to attract the ne gati v ely char ged toner particles to the paper .
3-57 F AX-L1000 Chapter 3: T echnical Reference 2.5.5 Fixing section As the toner image transferred onto the paper in the transfer block is only adhered by electrostatic attraction, even a light touch will smear the image. In the fixing block, the toner image is fixed by applying heat and pressure to the paper and the toner .
3-58 F AX-L1000 Chapter 3: T echnical Reference • This fax machine does not hav e "-A CVIN signal". • If the ECNT board CPU detects with the thermistor that the fixing heater temperature is ov er 428°F (220°C), it cuts of f the po wer to the fixing heater (Software protection).
3-59 F AX-L1000 Chapter 3: T echnical Reference 5 . When the thermistor is in the high temperature detection mode and the initial temperature is 185°F(85°C) or more, it does not exceed about 320°F(160°C) (about 284°F(140°C) in case of 1200DPI) within about 6 seconds after the heater is turned ON.
3-60 F AX-L1000 Chapter 3: T echnical Reference 2.6 Circuit Overview 2.6.1 SCNT board function block diagram Figure 3-29 Function Block Diagram (1) Display OPCNT board Serial communication function Bu.
3-61 F AX-L1000 Chapter 3: T echnical Reference 2.6.2 Functions a) SCNT board The SCNT board performs the following functions. Drive control The drive control section controls the document feed motor in the document scanning section.
3-62 F AX-L1000 Chapter 3: T echnical Reference Memory functions User data, service data, data registered before shipment from the f actory , and communications management information, are stored to the SRAM.
3-63 F AX-L1000 Chapter 3: T echnical Reference d) OPCNT board Buttons detection and LED drive function The control IC on the OPCNT board detects the buttons operation status, and drives the LCD and LEDs. Display The control IC in the LCD module controls the 20-column × 2-line LCD according to the display signals from the SCNT board.
3-64 F AX-L1000 Chapter 3: T echnical Reference 2.6.3 ECNT board function block diagra Figure 3-30 Function Block Diagram (2) ECNT board Horizontal synchronization signal (-BD) control paper size dete.
3-65 F AX-L1000 Chapter 3: T echnical Reference 2.6.4 Functions a) ECNT board Fixing heater control The fixing heater control section monitors the DC voltage supplied from the power supply in response to the A C 187~264 V , and the fixing heater thermistor , and dri ves the heater so that the temperature reaches the specified level.
3-66 F AX-L1000 Chapter 3: T echnical Reference T oner detection Signals are receiv ed from the antenna type toner sensor , and monitors the remaining toner of the toner cartridge.
3-67 F AX-L1000 Chapter 3: T echnical Reference 2.6.5 SCNT board component block diagram Figure 3-31 Component Block Diagram (1) M M Cam sensor Cam motor DC AC DC OPCNT board LED LCD Button P ow er supply Speaker ECNT board ROM 8M IC4 SRAM 256K IC5 RTC IC7 UHQ-6.
3-68 F AX-L1000 Chapter 3: T echnical Reference a) System control section (SCNT board) The system control section consists of the following components and controls the entire facsimile system. a-1) MPU (Micro Processor Unit) (IC 17) The MPU, on NEC UPD70741GC-25-7EA, has the following main functions.
3-69 F AX-L1000 Chapter 3: T echnical Reference a-4) DRAM (IC 3, 31) This 16-Mbit DRAM is backed up by rechar geable battery (approx. 12 hour after A C power interruption), and is used as memory for storing image data and MPU work area. a-5) SRAM (IC 5, 6) These 256-kbit SRAMs are backed up by lithium battery .
3-70 F AX-L1000 Chapter 3: T echnical Reference b-2) CODEC IC (IC 22) The main functions of the CODEC IC are as follows: •Scanner interface • Serial interface to image processing IC •Encoder •.
3-71 F AX-L1000 Chapter 3: T echnical Reference 2.6.6 ECNT board component block diagram Figure 3-32 Component Block Diagram (2) SL FA N SL SL SL FA N SL SL Recoding paper ov erload sensor 1 Recoding .
3-72 F AX-L1000 Chapter 3: T echnical Reference a) Printer control section (ECNT boar d) The printer control section consists of the following components and controls the LBP printer . a-1) Single chip microcomputer (IC 501) The single chip microcomputer has the following main functions.
3-73 F AX-L1000 Chapter 3: T echnical Reference 2.6.7 Flow of image signals a) G3 memory transmission (1) The image is scanned by the contact sensor , and the analog image data is sent to the SCNT board. (2) The image processing IC (IC20) converts the analog image data from the contact sensor into digital data.
3-74 F AX-L1000 Chapter 3: T echnical Reference Figure 3-33 T ransmission (6) (6) (6) (2) (5) A B D C E F NCU board J23 IC26 IC17 IC3 IC22 SCNT board A:Image processing IC B:CODEC IC C:DRAM D:MODEM IC.
3-75 F AX-L1000 Chapter 3: T echnical Reference b) G3 reception (1) The received image signal by L1, L2 is passed through a 2-line - 4-line conversion circuit in the NCU board, and amplified. The encoded data received by the MODEM IC (IC26) is read out by the CPU and then it is written into the DRAM (IC3) reception buf f er by the CPU.
3-76 F AX-L1000 Chapter 3: T echnical Reference Figure 3-34 Reception (1) (1) (4) (1) (4) (2) (5) (3) (5) (5) (6) A B D C E F NCU board Print out J23 IC26 IC18 IC17 IC3 IC22 J2 J32 J51 TWINS board ECN.
3-77 F AX-L1000 Chapter 3: T echnical Reference 3. NEW FUNCTION 3.1 High-speed T ransmission The image transmission time is reduced drastically compared with the previous models by the V .34 modem (maximum transmission speed 33600 bps) recommended by ITU-T .
3-78 F AX-L1000 Chapter 3: T echnical Reference NO TE 1. The V .34 protocol uses ECM. If the ECM SW in user data is set to OFF , the V .8 protocol is not e xecuted. Therefore, the V .34 protocol is not used, and V .17 or a lo wer protocol is selected.
3-79 F AX-L1000 Chapter 3: T echnical Reference b) T ypical protocol Figure 3-35 T ypical Protocol CNG ANSam JM CM CJ INFO0a INFO0c B A Connected to the line L1 L2 A B INFO0h S PP TRN PPh AL T MPh MPh.
3-80 F AX-L1000 Chapter 3: T echnical Reference b-1) Network interaction (Phase 1) The V .8 protocol is used as the startup protocol for high-speed modem V .34. The V .8 protocol determines the best modulation method (V -series modem mode) that is av ailable between the transmitter and receiv er .
3-81 F AX-L1000 Chapter 3: T echnical Reference b-2) Probing (Phase 2) The line characteristics are measured and modulation-related parameters, such as symbol rate, are set.
3-82 F AX-L1000 Chapter 3: T echnical Reference b-3) Primary channel equalizer training (Phase 3) Filters, such as equalizers, are trained (adjusted) with the parameters set in phase 2. • T ransmitter Abbre- Signal viation Meaning Remarks S signal S Short training The phase of S is shifted from S signal S the phase of S.
3-83 F AX-L1000 Chapter 3: T echnical Reference b-5) Control channel The con ventional T .30 protocol is ex ecuted. The transmission speed is 600bps. • T ransmitter Abbre- Signal viation Meaning Remarks Flag flags Maintain synchronization.
3-84 F AX-L1000 Chapter 3: T echnical Reference b-6) Primary channel resyncronization procedure T r aining is performed with the parameters set in phase 4. The transmission speed is 1200bps. • T ransmitter Abbre- Signal viation Meaning Remarks S signal S Short training The phase of S is shifted from S signal S the phase of S.
3-85 F AX-L1000 Chapter 3: T echnical Reference b-8) Control channel resyncronization procedure (Communication end procedure) Protocol for terminating transmission.
3-86 F AX-L1000 Chapter 3: T echnical Reference c) Examples of sequences The signals in the shaded areas are important in the protocol. c-1) Late start Since the recei ver cannot detect the CM signal while sending the ANSam signal, it sends the DIS signal containing the "V .
3-87 F AX-L1000 Chapter 3: T echnical Reference c-2) Between-page sequence The transmitter sends image data, then the PPS-MPS signal in the same as for the T .
3-88 F AX-L1000 Chapter 3: T echnical Reference c-3) Mode change The transmitter sends PPS-EOM and the receiv er sends the MCF signal. Then the recei ver sends the DIS signal and the transmitter sends the DCS signal to change the mode.
3-89 F AX-L1000 Chapter 3: T echnical Reference c-4) Image transmission speed change from the receiver The receiv er r eturns to the PPh signal in response to the Sh signal from the transmitter . The image transmission speed is then determined by the MPh sequence sent from both modems.
3-90 F AX-L1000 Chapter 3: T echnical Reference c-5) Image transmission speed change from the transmitter The transmitter sends image data, and then the PPh signal, and the receiver returns the PPh signal to the transmitter . The image transmission speed is then determined by the MPh sequence sent from both modems.
3-91 F AX-L1000 Chapter 3: T echnical Reference 3.2 JBIG Image Compression Encoding Method 3.2.1 Outline of the JBIG Image Compression Encoding Method The JBIG Image Compression Encoding Method is recommended in ITU-T T .
3-92 F AX-L1000 Chapter 3: T echnical Reference NO TE The characteristics of Progressi ve Bi-lev el Image Compression are explained below as a reference. First of all, after the original image has been read in at high resolution, it is converted to low resolution, and this low resolution image data proceeds to be encoded (compressed).
3-93 F AX-L1000 Chapter 3: T echnical Reference 3.2.3 Encoding Method In the JBIG encoding used in the Single Progression Sequential Bi-level Image Compression Method, uses in the encoder shown below .
3-94 F AX-L1000 Chapter 3: T echnical Reference b) In the model template, the combination (10-bit pixel pattern) of 10 pix els is output to the arithmetic encoding section using the template shown below (inside the bold outline). All of the 10-bit pixel patterns inside this template e xist in the study table.
3-95 F AX-L1000 Chapter 3: T echnical Reference Figure 3-44 P ositions of Pix els in Model T emplate T able 3-1 Study T able (Initial values) T able 3-2 Probability Estimation T able ST : Status numbe.
3-96 F AX-L1000 Chapter 3: T echnical Reference Example: A brief explanation of ho w the study table works is gi ven belo w . It is assumed that each of the model template pixels 1~10 in the image below are white. 1. In this case, the model template pixel pattern is 000h.
3-97 F AX-L1000 Chapter 3: T echnical Reference d) The probability estimation table, published in the ITU-T T .82. Its contents are fix ed, dif fering from those of the study table. NO TE This table shows probability of accuracy/inaccuracy in the form of a range, according to the accurate/inaccurate results of a given status prediction value.
3-98 F AX-L1000 Chapter 3: T echnical Reference The concept of arithmetic encoding is simply explained belo w . The following assumptions are made in order to make the explanation easy to understand. The probability of accuracy will be 50%, and the probability of inaccuracy will be 50%.
3-99 F AX-L1000 Chapter 3: T echnical Reference Next, the encoding for continuous accurate predictions will be simply explained. The assumptions below will be made for easy understanding. The value of an accurate LSZ will be decimal 100 *1 in all statuses.
3-100 F AX-L1000 Chapter 3: T echnical Reference 3.2.4 Construction of image data with JBIG Image Compression Encoding Images are encoded in block units called stripes, as shown in the f igure below .
3-101 F AX-L1000 Chapter 3: T echnical Reference 3.2.5 Explanation of Bi-level Image Header section (BIH) The BIH is shown in the construction f igure below .
3-102 F AX-L1000 Chapter 3: T echnical Reference 3.2.6 Explanation and parameters f or each symbol used in BIH The 0x of each parameter shows that the following integers are hexadecimal.
3-103 F AX-L1000 Chapter 3: T echnical Reference 3.2.7 Explanation of Bi-level Image Data (BID) section BID is as sho wn in the construction f igure belo w , and consists onl y of the number of stripes.
3-104 F AX-L1000 Chapter 3: T echnical Reference COMMENT (Private comment: 0x07) An optional comment may be added. ESC 0x07 Lc:Comment length NEWLEN (New length: 0x04) Redefine the document length. Only usable when VLENGTH=ON. ESC 0x04 YD:Document length RESER VE (Reserve: 0x01) Only usable for characteristic use.
3-105 F AX-L1000 Chapter 3: T echnical Reference 3.3 Energy Save Standby (ESS) a) Function ESS is an energy sa v e function for minimizing po wer loss during standby . During ESS, the ESS control section of the system control IC inside the SCNT board halts all oscillators other than the real time clock (R TC) IC in order to reduce power loss.
3-106 F AX-L1000 Chapter 3: T echnical Reference NO TE The po wer consumption at standby is 22 W in non-ESS mode and 2 W in ESS mode. The ESS function does not operate when the F AX-L1000 ISDN Kit or F AX-L1000 Printer Kit are installed.
Chapter 4 Maintenance and Ser vice.
.
4-1 F AX-L1000 Chapter 4: Maintenance and Service 1. MAINTENANCE 1.1 Maintenance Items 1.1.1 Consumables Level Consumable When User Canon FX 6 Cartridge When “INST ALL CAR TRIDGE” is displayed or when toner has run out. Stamp ink *1 When the stamp becomes thin.
4-2 F AX-L1000 Chapter 4: Maintenance and Service KANGAS W eight 80 g/m 2 Paper size A4 Manufactured by KANGAS NEUSIEDLER Canon Paper W eight 80 g/m 2 Paper size A4 Manufactured by NEUSIEDLER NO TE *3 Consumable parts are expected to require replacement at least once during the warranty period of this fax, due to deterioration or damage.
4-3 F AX-L1000 Chapter 4: Maintenance and Service 1.1.2 Cleaning Level Location When User Main unit outer cover When dirty . Document pick-up When document pick-up roller performance fails. Document separation When document separation or feed roller (upper) performance fails.
4-4 F AX-L1000 Chapter 4: Maintenance and Service Level Location When Service technician Multi-purpose tray When recording paper pick-up pick-up roller performance fails. Cassette pick-up When recording paper pick-up roller performance fails. Cassette separation When recording paper separation roller or feed performance fails.
4-5 F AX-L1000 Chapter 4: Maintenance and Service Level Location When Fixing pressure roller When marks on back of recording paper at intervals of 2.48" (63 mm), poor fixing, paper jam, or wrinkles in printed- out. Fixing eject roller When recording paper jam.
4-6 F AX-L1000 Chapter 4: Maintenance and Service 1.2 T ools 1.2.1 General tools T ool Use Phillips screwdriver Removing/inserting screws Slot head screwdriver Removing/inserting screws Precision phil.
4-7 F AX-L1000 Chapter 4: Maintenance and Service 2. CONSUMABLES REPLACEMENT 2.1 T oner Car tridg e REFERENCE For details on how to replace the toner cartridge, see Chapter 5: 1.4 Assembling the Fax . 2.2 Recording Paper REFERENCE For details on ho w to refill the paper , see Chapter 5, 1.
4-8 F AX-L1000 Chapter 4: Maintenance and Service 2.3 Stamp Ink Figure 4-1 Ref illing the Stamp Ink 1 1. Disconnect the power cord of the fax unit fr om its power sour ce. 2. Lift the document feeder tray , and gently open the ADF cover until it stops, grasping the document feeder tray and the ADF cover at the same time.
4-9 F AX-L1000 Chapter 4: Maintenance and Service Figure 4-2 Ref illing the Stamp Ink 2 Figure 4-3 Ref illing the Stamp Ink 3 4. Gently lift the ADF cover up to the full open position. 5. Locate the stamp pad then apply only one drop of ink to the stamp ink compartment.
4-10 F AX-L1000 Chapter 4: Maintenance and Service 6. Close the ADF cover , lower the document feeder tray , and connect the power cord of the fax unit to the power sour ce. • Make sure that you do not drip ink on any other part of the fax. • Make sure that you put the plastic loop back in place when you close the ADF cover .
4-11 F AX-L1000 Chapter 4: Maintenance and Service 3. CLEANING 3.1 Main Unit W ipe any dirt of f with a soft, dry cloth. 3.2 Document Pick-up Roller Open the upper reader frame unit and wipe any dirt of f with a soft, dry cloth. 3.3 Separation Roller (Upper) Open the upper reader frame unit and wipe any dirt of f with a soft, dry cloth.
4-12 F AX-L1000 Chapter 4: Maintenance and Service Figure 4-4 Cleaning Location 1 Figure 4-5 Cleaning Location 2 Do not use tissue. Otherwise, paper dust may stick to the parts or a static charge may be generated. NO TE In cases where there is a lot of dirt in item 3.
4-13 F AX-L1000 Chapter 4: Maintenance and Service 3.10 T ransfer Guide a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Lift the document feeder tray , the document output tray and the upper output tray .
4-14 F AX-L1000 Chapter 4: Maintenance and Service b) Cleaning (1) Using a soft clean cloth, wipe any paper dust of f the black plate of the transfer guide. Figure 4-8 Cleaning Location 1 (2) While holding the green le ver , flip the transfer guide up.
4-15 F AX-L1000 Chapter 4: Maintenance and Service (3) Pull the transfer guide back to its full extent, then wipe the silv er metal strip with cloth. Then gently guide the transfer guide back to its original position. Figure 4-10 Cleaning Location 3 NO TE The spring for the transfer guide is strong.
4-16 F AX-L1000 Chapter 4: Maintenance and Service 3.11 T ransfer Charging Roller a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Lift the document feeder tray , the document output tray and the upper output tray .
4-17 F AX-L1000 Chapter 4: Maintenance and Service b) Cleaning (1) Using lint-free paper , wipe any dirt of f the transfer char ging roller . Figure 4-12 Cleaning Location NO TE Do not touch or hold the rubber section of the transfer charging roller .
4-18 F AX-L1000 Chapter 4: Maintenance and Service 3.12 Cassette Pick-Up Roller/Feed Roller/Separation Roller a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Disconnect the telephone line mojular jack cord.
4-19 F AX-L1000 Chapter 4: Maintenance and Service b) Cleaning (1) Using lint-free paper dipped in alcohol, wipe any dirt of f the cassette pick-up roller and the cassette feed roller while rotating the shaft in the indicated direction.
4-20 F AX-L1000 Chapter 4: Maintenance and Service 3.13 Multi-Purpose T ray Pic k-Up Roller/Separation P ad a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Open the multi-purpose tray . (3) Remov e the entrance co ver .
4-21 F AX-L1000 Chapter 4: Maintenance and Service b) Cleaning (1) Using lint-free paper dipped in alcohol, wipe any dirt of f the multi-purpose tray pick-up roller . Figure 4-19 Cleaning Location 1 ( 2 ) Using lint-free paper dipped in alcohol, wipe any dirt of f the multi-purpose tray separation pad.
4-22 F AX-L1000 Chapter 4: Maintenance and Service 3.14 Feed Roller a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source.
4-23 F AX-L1000 Chapter 4: Maintenance and Service (4) Remov e the right co ver , front right cov er , rear cov er and the read motor cov er . (5) Remove the joint of the printer cover using the needle nose prier and release the claw using the precision slot head scre w dri v er .
4-24 F AX-L1000 Chapter 4: Maintenance and Service (10) Remove the shield cover and the operation panel. Figure 4-25 Pr eparation for Cleaning 5 (11) Remov e the PCBs and the metal frame.
4-25 F AX-L1000 Chapter 4: Maintenance and Service (12) Remove the entrance co v er . (13) Disconnect the multi-purpose paper sensor cable. Figure 4-27 Pr eparation for Cleaning 7 (14) Remove the two long screws. (15) Remove the one scre w of the en v elope feeder gear cov er .
4-26 F AX-L1000 Chapter 4: Maintenance and Service b) Cleaning (1) After removing the en velope feeder gear co ver and the multi-purpose pick-up ass’y , using lint-free paper dipped in alcohol, wipe any dirt of f the feed roller while rota ting the gear .
4-27 F AX-L1000 Chapter 4: Maintenance and Service 3.15 Pre-T ransfer Roller and Registration Arm a) Preparations for cleaning (1) Refer to 3.14 Feed Roller to remove the envelope feeder gear cover and the multi- purpose pick-up ass’y . (2) Remove the six screws.
4-28 F AX-L1000 Chapter 4: Maintenance and Service b) Cleaning (1) Using lint-free paper dipped in alcohol, wipe any dirt off the pre-transfer roller and registration arm.
4-29 F AX-L1000 Chapter 4: Maintenance and Service 3.16 Paper Feed Belt and Paper Feed Guide a) Preparations for cleaning (1) Refer to 3.11 T ransf er Charging Roller to remov e the transfer char ging roller . (2) Remov e the paper feed roller using the precision slot head scre wdriv er .
4-30 F AX-L1000 Chapter 4: Maintenance and Service (2) Using lint-free paper dipped in alcohol, wipe any dirt of f the paper feed guide. Figure 4-35 Cleaning Location 2 P aper f eed guide.
4-31 F AX-L1000 Chapter 4: Maintenance and Service 3.17 Fixing Unit Entrance Guide a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Remov e the right rear cov er and the left rear cov er . (3) Remov e the face-up tray .
4-32 F AX-L1000 Chapter 4: Maintenance and Service 3.18 Fixing Film a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Refer to 3.17 Fixing Unit Entrance Guide to remov e the f ixing ass’y . (3) While pushing the claw , remove the left f ixing ass’y connector .
4-33 F AX-L1000 Chapter 4: Maintenance and Service (4) Remov e the upper crossmember . Figure 4-40 Pr eparation for Cleaning 3 b) Cleaning (1) Using lint-free paper , wipe any dirt of f the f ixing f ilm. Figure 4-41 Cleaning Location NO TE When cleaning, be careful not to touch the fixing film.
4-34 F AX-L1000 Chapter 4: Maintenance and Service 3.19 F ace-Up Deflector , Fixing Delivery Roller and Lower P aper Delivery Guide a) Preparations for cleaning (1) Disconnect the power cord of the fax from the power source. (2) Refer to the Figure 4-36, 4-37 and 4-40 to remov e the upper crossmember .
4-35 F AX-L1000 Chapter 4: Maintenance and Service 4. ADJUSTMENT 4.1 Parts Replacement Please refer to the separate P AR TS CA T ALOG for disassembly / assembly procedures to follow when replacing parts. The P ARTS CA T ALOG shows illustrations which follo w the disassembly procedures.
4-36 F AX-L1000 Chapter 4: Maintenance and Service 4.4 Leading Edge Margin Adjustment a) When As VR501 on the ECNT board is adjusted at the factory , its adjustment at the time of installation is not required. Howe ver , when the ECNT board is replaced in the field, the leading edge mar gin needs to be readjusted.
4-37 F AX-L1000 Chapter 4: Maintenance and Service (7) Make several test prints again, and perform step (5). Check that the leading edge margin is 2.0mm.
4-38 F AX-L1000 Chapter 4: Maintenance and Service 5. TROUBLESHOOTING 5.1 T r oubleshooting 5.1.1 Repairs a) Check installation environment Check that the following conditions have been met with regard to installation environment. (1) This fax must be installed on a level surface.
4-39 F AX-L1000 Chapter 4: Maintenance and Service 5.2 Error Shown on the Display 5.2.1 User error message "# ALREAD Y IN USE" Cause: The box specified with conf idential or polling communications is already in use. Solution: Change the setting or select another box.
4-40 F AX-L1000 Chapter 4: Maintenance and Service "CHECK POLLING ID" (#0008, #0021) Cause: Polling was impossible because the polling ID or your subaddress/ password did not match. Solution: Check the polling ID or subaddress/password with the other party and try polling again.
4-41 F AX-L1000 Chapter 4: Maintenance and Service "ENTER DAC" Cause: The department access code is not entered to send document. Solution: Enter the department access code. "HANG UP PHONE" Cause: The handset was left of f the hook after the completion of transmission or reception.
4-42 F AX-L1000 Chapter 4: Maintenance and Service "NO RX P APER" (#0012) Cause: Declares that the other fax has no recording paper for DIS. Solution: Contact the other party and have them load paper into their fax.
4-43 F AX-L1000 Chapter 4: Maintenance and Service "REC. P APER JAM" (#0009) Cause: Recording paper jam This is displayed when the pre-feed sensor or the fixing unit delivery sensors 1&2 detects a paper jam.
4-44 F AX-L1000 Chapter 4: Maintenance and Service "ST OP KEY PRESSED" Cause: Y ou hav e pressed the Stop button to cancel the current transaction.
4-45 F AX-L1000 Chapter 4: Maintenance and Service 5.2.2 Error codes a) Service error code output If Service Data #1 SSSW SW01 bit 0 is set to “1”, then service error codes are printed on the activity management reports, reception result reports, error transmission reports, and system dump lists when communication ends in an error .
4-46 F AX-L1000 Chapter 4: Maintenance and Service •Echo measures Change the follo wing bit switches of service data #1SSSW SW03 . Bit 4 → 1: Ignore the first DIS signal sent by the other f ax machine. 0: Not to ignore the first DIS signal sent by the other fax machine.
4-47 F AX-L1000 Chapter 4: Maintenance and Service c) Error code list The error codes used for this fax are as follows. Codes listed as “New” in the list below indicate new error codes, or codes whose measures dif fer from those listed in the separate document G3 F acsimile Error Code List (Rev .
4-48 F AX-L1000 Chapter 4: Maintenance and Service No. Tx or Rx Definition #0995 [ TX/RX ] The image data stored in memory have been cleared c-2) Service error codes • G3 mode error codes No.
4-49 F AX-L1000 Chapter 4: Maintenance and Service No. Tx or Rx Definition ##0290 [ TX ] Receiv e signals other than PIN, PIP , MCF , R TP or R TN after MPS transmission • Printer error codes No.
4-50 F AX-L1000 Chapter 4: Maintenance and Service • ECM mode error codes No. Tx or Rx Definition ##0750 [ TX ] Exceed repeat protocol due to failure to receive significant signals after transmittin.
4-51 F AX-L1000 Chapter 4: Maintenance and Service No. Tx or Rx Definition ##0770 [ TX ] Exceed repeat protocol limit due to failure to receive significant signals after transmitting EOR-NULL during E.
4-52 F AX-L1000 Chapter 4: Maintenance and Service No. Tx or Rx Definition ##0792 [ RX ] Fail to detect PPS-NULL between partial pages during ECM reception ##0793 [ RX ] T ime over due to failure to r.
4-53 F AX-L1000 Chapter 4: Maintenance and Service d) Recovery methods for codes indicated as “New” d-1) User error codes #0001 [TX] Paper jam Cause: The document jammed in the fax machine. Solution: Remove the document and transmit/copy again. Cause: The document width size or thickness does not meet the standards.
4-54 F AX-L1000 Chapter 4: Maintenance and Service Cause: Internal structure defect Solution: (1) Check if the document edge sensor (DES) is operating correctly using the methods gi v en in Chapter 2: 2.4.7 F aculty tests , T est Mode [6] Faculty T est, [3] Sensor T ests.
4-55 F AX-L1000 Chapter 4: Maintenance and Service #0009 [RX] Recording paper jam or out of paper Cause: The recording paper jammed. Solution: Clear the recording paper jam.
4-56 F AX-L1000 Chapter 4: Maintenance and Service (21) Check the recording paper eject sensor 2, the cable and the fixing unit (J131) connections. (22) Replace the recording paper eject sensor 2. (23) Replace the ECNT board. (24) Replace the ECNT board.
4-57 F AX-L1000 Chapter 4: Maintenance and Service #0059 [TX] The number you dial and connected number (CSI) does not match Cause: “ USER TEL ” on the reception side not programmed, or wrongly programmed. Solution: (1 ) Contact reception side and check whether “ USER TEL ” has been properly programmed.
4-58 F AX-L1000 Chapter 4: Maintenance and Service #0099 [TX/RX] Pressed stop button during communication Cause: The Stop b utton was pressed during communication. Solution: T r y transmit or receiv e again. #0102 [TX] In transmission, DCN received in response to password/sub- address Cause: Password/subaddress does not match.
4-59 F AX-L1000 Chapter 4: Maintenance and Service d-2) Service error codes • Printer error codes ##0322 [RX] Fixing heater temperature abnormality Cause: Y our fax is connected to a UPS (Uninterruptable Power Supply).
4-60 F AX-L1000 Chapter 4: Maintenance and Service • V .8/V .34 protocol error codes ##0670 [TX] At V .8 late star t, the called par ty declares the V .8 pr otocol in DIS signal and this unit transmits a CI signal, but the protocol does not progress and a T1 time-out occurs.
4-61 F AX-L1000 Chapter 4: Maintenance and Service ##0675 [RX] The protocol did not move from phase 3 to phase 4 and a T1 time-out occurred during V .34 reception. Cause: The transmitter disconnected the line during phase 3 or the signal from the transmitter was not able to be detected.
4-62 F AX-L1000 Chapter 4: Maintenance and Service • ECM mode error codes ##0753 [TX] Exceed protocol retransmission limit or T5 time (60 seconds) after PPS-NULL transmission during ECM transmission.
4-63 F AX-L1000 Chapter 4: Maintenance and Service ##0773 [TX] Exceed protocol retransmission limit or T5 time (60 seconds) after EOR-NULL transmission during ECM transmission Cause: The other fax’ .
4-64 F AX-L1000 Chapter 4: Maintenance and Service 5.3 Err ors not Shown on the Displa y a) No power Solution: (1) Plug in the power cord. (2) Check the fuse in the power supply unit. If the fuse (F1, F2) blows, replace the fuse. (3) Check the power supply and ECNT board (J101) connections.
4-65 F AX-L1000 Chapter 4: Maintenance and Service Document read motor does not run at all or dose not run normally Solution: (1) Make a copy , and make sure that the document read motor is operating correctly . (2) Check the SCNT board (J4) and document read motor connections.
4-66 F AX-L1000 Chapter 4: Maintenance and Service V er tical black band in images Solution: (1) Clean the white sheet of the middle reader frame unit. (2) Clean the scanning glass. (3) Set SSSW #1 SW06 Bits 0 and 1 to "1", as explained in the separate document G3 F acsimile Ser vice Data Handbook (Rev .
4-67 F AX-L1000 Chapter 4: Maintenance and Service P oor fixing Distor tion -BD f ailure Irregular and smudged blac k hor izontal lines Blank spots White ver tical lines Irregular and smudged blac k v.
4-68 F AX-L1000 Chapter 4: Maintenance and Service Light Solution: (1) In user data, set “ SELECT DENSITY ” of “ F AX’S PRINTER SET ” to “ DK ”.
4-69 F AX-L1000 Chapter 4: Maintenance and Service All black Solution: (1) Clean the high-voltage terminal and the toner cartridge contact. (2) Replace the toner cartridge. (3) Replace the ECNT board. Dots Solution: (1) Clean the static charge eliminator with brush.
4-70 F AX-L1000 Chapter 4: Maintenance and Service Black vertical lines Solution: (1) Clean the mirror . (2 ) During printing, open the printer cover , remo ve the toner cartridge drum protective shutter by hand, and check if there are vertical black lines on the photosensitive drum.
4-71 F AX-L1000 Chapter 4: Maintenance and Service Marks Solution: (1) Copy a few white paper documents. (2) If the marks is at intervals of approx. 3.70" (94 mm), replace the toner cartridge. (3) If the marks is at intervals of approx. 2.97" (75 mm), clean the cassette separation roller .
4-72 F AX-L1000 Chapter 4: Maintenance and Service Faulty registration Solution: (1) Check if more than the regulation amount of recording paper is loaded in the cassette. (2) Clean the cassette pickup roller . (3) Clean the multi-purpose tray pickup roller .
4-73 F AX-L1000 Chapter 4: Maintenance and Service NO TE Checking the nip width of the pressure roller The fixing unit is not designed to allow adjustment of the pressure (nip width); ho we v er , the incorrect nip width can cause fixing problems.
4-74 F AX-L1000 Chapter 4: Maintenance and Service h) Recording paper pickup error The recording paper is not picked up from the multi-purpose tray Solution: (1) Check that the recording paper is not curled and is set correctly . (2) Check if more than the regulation amount of recording paper is loaded in the multi-purpose tray .
4-75 F AX-L1000 Chapter 4: Maintenance and Service Recording paper is not picked up from the cassette 2 (Option paper feeder) Solution: (1) Check that the cassette 2 is installed correctly . (2) Check if more than the regulation amount of recording paper is loaded in the cassette 2.
4-76 F AX-L1000 Chapter 4: Maintenance and Service i) Recording paper feed error The recording paper is not fed between transfer and feed section Solution: (1) When a paper 180mm or less in length is jammed before reaching the fixing roller , examine whether the paper is curled do wnward.
4-77 F AX-L1000 Chapter 4: Maintenance and Service The recording paper is not fed between fixing and delivery section Solution: (1) If the nip width is not within the specification, replace the f ixing ass’y .
4-78 F AX-L1000 Chapter 4: Maintenance and Service Multiple feed Solution: (1) If jams occur in the multi-purpose tray , go to step (7) and thereafter . (2) Set the paper caught by the claw of the cassette. (3) Check the cassette claw . If it is deformed, replace it.
4-79 F AX-L1000 Chapter 4: Maintenance and Service j) Printer error PRINTER ERROR MESSAGES Solution: (1) For the detail of the printer error messages, refer to the Chapter 5, 3.10 F AX-L1000 Pr inter Kit, 3.10.4 Maintenance and service, b) T roub leshooting .
4-80 F AX-L1000 Chapter 4: Maintenance and Service 6. WIRING DIAGRAM 6.1 Wiring Diagram Figure 4-48 Wi ring Diagram (1) 2 2 J1 2 J2 J1 J2 10 10 MODULAR OPCNT2 Modular cord 2 10 J1 J2 10 15 15 J5 J100 .
4-81 F AX-L1000 Chapter 4: Maintenance and Service Figure 4-49 Wi ring Diagram (2) ENVELOP FEEDER(Option) T ONER CARTRIDGE LASER/SCANNER UNIT for Pow er supply unit P APER FEED UNIT PF-52 (Option) P a.
4-82 F AX-L1000 Chapter 4: Maintenance and Service Figure 4-50 Wi ring Diagram (3) Update PDL ROM DIMM 72 Update ROM DIMM sock et (bank 0) PS3 ROM DIMM 72 PS3 ROM DIMM sock et (bank 1) J6 J7 J8 Not us.
4-83 F AX-L1000 Chapter 4: Maintenance and Service 6.2 Signal Description SCNT boar d (J1) ,/ Memory board J1 Memory Signal name Description A1 . 1 DGND Ground A2 . 2 VD0 Data signal A3 . 3 VD1 Data signal A4 . 4 VD2 Data signal A5 . 5 VD3 Data signal A6 .
4-84 F AX-L1000 Chapter 4: Maintenance and Service SCNT board (J1) ,/ Memory board J1 Memory Signal name Description A43 / 43 nCASH Column address/high-order byte access A44 / 44 nRAS2 Row address strobe signal No.2 A45 . 45 N.C Not connected A46 . 46 N.
4-85 F AX-L1000 Chapter 4: Maintenance and Service SCNT boar d (J2) ,/ TWINS board (J31) J2 J31 Signal name Description 1 / 1 V A5 Address signal 2 / 2 V A4 Address signal 3 / 3 V A3 Address signal 4 / 4 V A2 Address signal 5 / 5 V A1 Address signal 6 / 6 V A0 Address signal 7 .
4-86 F AX-L1000 Chapter 4: Maintenance and Service SCNT board (J2) ,/ TWINS board (J31) J2 J31 Signal name Description 44 , 44 +24V +24V 45 , 45 DGND Ground 46 , 46 +5V +5V 47 / 47 +5V +5V(off while ESS) 48 . 48 DGND Ground 49 / 49 +3.3V +3.3V 50 . 50 DGND Ground 51 .
4-87 F AX-L1000 Chapter 4: Maintenance and Service SCNT boar d (J2) ,/ TWINS board (J31) J2 J31 Signal name Description 87 , 87 +5V +5V 88 , 88 OPTION3 Option board detection signal 3 89 , 89 PCLK Pri.
4-88 F AX-L1000 Chapter 4: Maintenance and Service SCNT board (J5) ,/ OPCNT boar d 1(J100) J5 J100 Signal name Description 1 / 18 +5V +5V 2 / 17 +5V +5V 3 / 16 ESSLED ESS LED drive signal 4 , 15 ESSKEY ESS key input signal 5 , 14 PR TCT SRAM protect signal 6 , 13 PNLRX Panel data receive signal 7 .
4-89 F AX-L1000 Chapter 4: Maintenance and Service SCNT boar d (J9) ,/ NCU board (J1) J9 J1 Signal name Description 1 . 23 DGND Ground 2 , 22 BIT3 for future use 3 , 21 BIT2 for future use 4 , 20 BIT1 for future use 5 . 19 LPL2 Not used 6 . 18 LPL1 Not used 7 .
4-90 F AX-L1000 Chapter 4: Maintenance and Service SCNT board (J12) ,/ Sensor board(J1) J12 (J1) Signal name Description 1 / 1 1 +3.3V +3.3V(of f while ESS) 2 .
4-91 F AX-L1000 Chapter 4: Maintenance and Service SCNT boar d (J25) ,/ NCU board (J6) J25 J6 Signal name Description 1 . 14 OUT Direct current of line detection signal 2 / 13 IPSEL1 HIC terminal impedance setting 3 / 12 IPSEL2 HIC terminal impedance setting 4 .
4-92 F AX-L1000 Chapter 4: Maintenance and Service NCU board (J8) ,/ Modular boar d (J3) J5 G.wire Signal name Description 1 . 1 1 A Line from handset terminal T12 in priority mode (handset/extension telephone). 2 . 10 W Line from handset terminal T11 in priority mode (handset/extension telephone).
4-93 F AX-L1000 Chapter 4: Maintenance and Service ECNT boar d (J101) ,/ P o wer supply unit J101 PSU Signal name Description 1 , 1 HOT AC power input 2 , 2 NEUTRAL AC power input ECNT boar d (J31) ,/ Fixing unit(J131) J31 J131 Signal name Description 1 , 1 THRM Thermistor signal 2 .
4-94 F AX-L1000 Chapter 4: Maintenance and Service ECNT board (J52) ,/ Main motor(J301) J52 J301 Signal name Description 1 / 7 nHALF Main motor speed switching signal 2 , 6 nMRDY Main motor ready signal 3 / 5 +24V Main motor drive voltage 4 / 4 +24V Main motor drive voltage 5 / 3 nMON Main motor drive signal 6 .
4-95 F AX-L1000 Chapter 4: Maintenance and Service ECNT board (J55F) ,/ Not used J55F Signal name Description 1 .. DGND Not connected 2 ,. RxD Not connected 3 /.
4-96 F AX-L1000 Chapter 4: Maintenance and Service ECNT board (J59) ,/ Printer co ver sensor (J119F) J59 J119F Signal name Description 1 / 2 +24V A Printer cover sensor drive voltage 2 .
4-97 F AX-L1000 Chapter 4: Maintenance and Service ECNT boar d (J72) ,/ Paper size boar d(J603) J72 J603 Signal name Description 8 / 7 SL1 Pick-up module identification signal 1 Lower cassette pick-up.
4-98 F AX-L1000 Chapter 4: Maintenance and Service ECNT board (J101) ,/ TWINS board(J42) J101 Signal name Description 10 , 1 MODRST Modem reset signal 11 , 2 CLKCTL Clock control signal ECNT board (J1.
4-99 F AX-L1000 Chapter 4: Maintenance and Service TWINS board (J31) ,/ SCNT board (J2) J31 J 2 Signal name Description 18 , 18 CLKCTK Clock control signal 19 , 19 TC T erminal count 20 , 20 DACK2 DMA.
4-100 F AX-L1000 Chapter 4: Maintenance and Service TWINS board (J31) ,/ SCNT boar d (J2) J31 J 2 Signal name Description 61 . 61 VD3 Data signal 62 . 62 VD2 Data signal 63 . 63 VD1 Data signal 64 . 64 VD0 Data signal 65 / 65 +5V +5V 66 / 66 ESSACT ESSACT 67 , 67 FIORD IO read signal 68 , 68 FIOWR IO write signal 69 .
4-101 F AX-L1000 Chapter 4: Maintenance and Service TWINS board(J32) ,/ ECNT board (J51) J32 J51 Signal name Description 1 . 1 DGND Ground 2 , 2 nBD Beam detection signal 3 / 3 nPPRDY Printer power re.
4-102 F AX-L1000 Chapter 4: Maintenance and Service TWINS board(J33) ,/ F AX-L1000 Printer kit (J2) J33 J2 Signal name Description 11 . c16 DGND Ground 12 , c15 nCCLK Controller clock signal 13 , c14 nCMD Command signal 14 .
4-103 F AX-L1000 Chapter 4: Maintenance and Service TWINS board(J36) ,/ P ower supply unit (J202) J36 J202 Signal name Description 5 / 5 +24V +24V(off while ESS) 6 . 6 24GND Ground 7 . 7 24GND Ground 8 / 8 +5V +5V 9 / 9 +5V +5V 10 . 10 GND Ground 11 .
4-104 F AX-L1000 Chapter 4: Maintenance and Service TWINS board (J39) ,/ ISDN G4 board (J1) (F AX-L1000 ISDN KIT) J39 J700 Signal name Description A13 . A8 PD6 Data signal A14 . A7 PD5 Data signal A15 . A6 PD4 Data signal A16 . A5 PD3 Data signal A17 .
Chapter 5 Appendix.
.
5-1 F AX-L1000 Chapter 5: Appendix 1. INST ALLA TION Here is the procedure for installing this fax. Contents 1.1 Setting up the Fax • Where to set up the fax • Space around the fax • Power requirements 1.2 Unpacking 1.3 Removing the Shipping Material 1.
5-2 F AX-L1000 Chapter 5: Appendix 1.1 Setting up the Fax CAUTIONS SHOW YOU HOW TO A VOID CONDITIONS OR INCORRECT OPERA TIONS THA T COULD CAUSE DAMAGE TO YOUR HARDW ARE OR SOFTW ARE OR CAUSE PERSONAL IN- JUR Y . This icon denotes feeding a document. Where to Set Up the F ax ❏ A void direct sunlight.
5-3 F AX-L1000 Chapter 5: Appendix ❏ Choose a location that is clean and free fr om dust and moisture. ❏ Do not use or store the fax outdoors. ❏ Place the fax unit near a telephone line.
5-4 F AX-L1000 Chapter 5: Appendix Space Ar ound the F ax T o ensure proper ventilation and easy operation, set up the fax in an ar ea that meets the minimum requir ements for clearance as illustrated below . TO A VOID DAMAGE TO THE F AX UNIT FROM OVERHEA TING, DO NOT BLOCK THE EXHAUST VENT .
5-5 F AX-L1000 Chapter 5: Appendix P o wer Requirements ❏ Place the fax near a standard 200 – 240 V AC power outlet. This fax unit is intended for domestic use. Do not attempt to use it outside the country where you pur chased it. ❏ Do not plug the power cord into an extension cor d connector or power strip shared with other plugs.
5-6 F AX-L1000 Chapter 5: Appendix Unpac king: Have Y ou Got Ever ything? As you unpack the fax, save the carton and packing material in case you want to move or ship the fax unit in the future. Ask someone to help you remove all items fr om the box. LIFTING THE F AX UNIT REQUIRES TWO PEOPLE.
5-7 F AX-L1000 Chapter 5: Appendix 3. Remove the four stoppers on the side of the box by squeezing the center grip. 4. Lift and remove the upper carton. Remove the four styr ene foam blocks positioned on top of the fax unit. Then lift the fax unit by gripping the handles on the right and left sides.
5-8 F AX-L1000 Chapter 5: Appendix Check each item against this list as you remove it fr om the box. ❏ 1 Fax machine ❏ 1 Document feeder tray ❏ 1 Document output tray ❏ 1 Upper output tray ❏.
5-9 F AX-L1000 Chapter 5: Appendix FAX UNIT (with Paper Cassette 1 installed) DOCUMENT OUTPUT TRA Y UPPER OUTPUT TRA Y FX6 T ONER CARTRIDGE DOCUMENT FEEDER TRA Y F A CSIMILE USER’S GUIDE DESTINA TIO.
5-10 F AX-L1000 Chapter 5: Appendix Remo ving the Shipping Material All shipping materials must be removed. Shipping materials ar e attached inside the fax unit and inside the paper cassette to protect delicate parts from vibration during shipping. Removing the Shipping T apes Remove all the shipping tapes from the unit.
5-11 F AX-L1000 Chapter 5: Appendix 2. Close the ADF cover . 3. Open the printer cover and the MP tray . 4. Remove the tapes and packing materials..
5-12 F AX-L1000 Chapter 5: Appendix 5. Close the printer cover and the MP tray . • Save all the packing materials. Y ou may want to insert them again if you have to transport the fax unit. • When removing the packing materials fr om inside the printer ar ea, be careful not to touch the transfer char ging r oller .
5-13 F AX-L1000 Chapter 5: Appendix Removing the Pr otective Plastic Sheet The LCD on the operation panel is covered with a plastic sheet to pr otect it during shipping.
5-14 F AX-L1000 Chapter 5: Appendix Assembling the F ax Follow the instructions in this section to assemble the fax and pr epare it for full operation.
5-15 F AX-L1000 Chapter 5: Appendix Save the protective bag and all other shipping material. Y ou will need this material later when you dispose of the cartridge after it has run out of toner . 3. Hold the cartridge by the ends and rock it gently five or six times to distribute the toner evenly inside the cartridge.
5-16 F AX-L1000 Chapter 5: Appendix 6. T o avoid pinching your fingers between the toner cartridge and fax unit, grip the cartridge as shown below . 7. Load the cartridge in the direction indicated by the arr ow . Gently slide the cartridge into the printer area until it is down inside the fax unit and level.
5-17 F AX-L1000 Chapter 5: Appendix Attaching the Document Output T ray and the Upper Out- put T ra y 1. Attach the upper output tray to the front of the fax unit. Slide the end of the upper output tray down into the fax unit at an incline, lifting the end nearest you.
5-18 F AX-L1000 Chapter 5: Appendix Make sure the knobs on each side of the tray fit into the holes on the side of the fax unit. Back of the tray sits on top of the extended lip of the fax unit. Attaching the Document Feeder T ray Slide one side in position first and then the other side.
5-19 F AX-L1000 Chapter 5: Appendix Installing P aper Feed Unit (PF-52) (option) 1. T ake out Paper Feed Unit (PF-52) from its carton box. 2. Remove the tape at the front of Paper Feed Unit (PF-52).
5-20 F AX-L1000 Chapter 5: Appendix 4. If tapes are attached to the paper cassette, r emove them. Then remove the spacers under the paper guide clips by first pr essing down on the bottom metal plate with one hand and then sliding the white spacers inwards with the other hand.
5-21 F AX-L1000 Chapter 5: Appendix 7. Replace the cassette into Paper Feed Unit (PF-52) and place it in the location you wish to use the fax after the cassette has been installed. Y ou will need to move the fax unit if you want to use it in the same location it now occupies.
5-22 F AX-L1000 Chapter 5: Appendix 9. Make sure the fr ont of the fax unit is facing the same dir ection as the front of Paper Feed Unit (PF-52). Slowly lower the fax unit onto the four positioning poles on the corners of Paper Feed Unit (PF-52).
5-23 F AX-L1000 Chapter 5: Appendix Loading P aper in P aper Cassettes 1 and 2 Before you load paper , follow these general guidelines: ❏ The paper cassettes can be adjusted to hold various sizes of paper . Paper Cassette 1 holds letter-, legal- or A4-size paper , and Paper Cassette 2 holds letter-, legal-, A4-, executive- or B5-size paper .
5-24 F AX-L1000 Chapter 5: Appendix 1. Pull out the paper cassettes from the fax unit. 2. Check if the selectors inside the paper cassettes are set for the size of the paper you are loading. If the setting is correct, go on to step 3. -if not- Set the paper cassettes to fit the sizes of the paper you are loading.
5-25 F AX-L1000 Chapter 5: Appendix Lift the stopper in the center of the paper size rear guide slightly , and slide it to the mark indicating the desired paper size.
5-26 F AX-L1000 Chapter 5: Appendix Push up the stopper of the paper size rear guide, and slide it to the mark indicating the desired paper size. Y ou can load executive- or B5-size paper in Paper Cassette 2 only when you use it for the printer function.
5-27 F AX-L1000 Chapter 5: Appendix 3. Before you load a stack of paper into the paper cassettes, tap the leading edge of the paper stack on a flat surface so that the edges are evenly aligned. 4. Place the stack of paper in the paper cassettes with the print side facing down.
5-28 F AX-L1000 Chapter 5: Appendix 5. Press down on the fr ont of the paper stack to make sure the corners are below the paper size guide clips. Then pr ess the stack down again to make sure it is below the paper limit marks on the side of the paper cassettes and the paper size guides hook at the back of the cassettes.
5-29 F AX-L1000 Chapter 5: Appendix 7. Reinsert the cassette into the fax unit: Align the cassette with the rails on the fax unit, then lift slightly to insert the cassette. Slide it all the way into the fax unit. Make sure you insert the cassette all the way into the fax unit until it locks into place.
5-30 F AX-L1000 Chapter 5: Appendix Connecting an Extension Phone T o connect an extension phone to the fax, you have to use the extension phone jack. Only one jack is provided to be used with the optional handset or an extension phone. A separate jack is not provided for an extension phone.
5-31 F AX-L1000 Chapter 5: Appendix Using the MP T ra y The MP (multi-purpose) tray can hold letter -, legal- or A4-size paper . The capacity is approximately 100 sheets of cut-sheet paper (80 g/m 2 ). T o use the MP tray as one of the input trays, you need to set USE MP TRA Y to ON in the F AX’S PRINTER SET menu.
5-32 F AX-L1000 Chapter 5: Appendix • A void pressing or applying excessive force on the MP tray as this may cause damage. • The paper stack must not exceed the paper limit mark. • Do not load differ ent sizes of paper on the MP tray at the same time.
5-33 F AX-L1000 Chapter 5: Appendix 1. Pull the MP tray out using the handle on the panel. 2. Pull out the extension tray using the center grip. 3. The MP tray holds appr oximately 100 sheets of paper . Befor e you load paper on the MP tray , tap the edges of the stack to make sure the leading edge and sides of the stack are even.
5-34 F AX-L1000 Chapter 5: Appendix 4. Insert the paper stack as far as it will go into the fax unit, with the print side facing up and the top of the paper going into the fax unit first.
5-35 F AX-L1000 Chapter 5: Appendix • Make sure that the paper guides are set corr ectly . T o print with the MP tray , you also need to select the paper size in the USE MP TRA Y menu. • Make sure that the paper is loaded correctly and that the leading edge is fully inserted into the fax unit.
5-36 F AX-L1000 Chapter 5: Appendix T urning on and off USE MP TRA Y and Setting the P aper Size in the USE MP TRA Y Menu T o use the MP tray as one of the input trays, you need to set USE MP TRA Y to ON in the F AX’S PRINTER SET menu.
5-37 F AX-L1000 Chapter 5: Appendix Set 5. Press Set . USE MP TRA Y OFF 6. Press the sear ch buttons to display ON. USE MP TRA Y ON If you use the MP tray for the printer function and load paper of sizes other than letter , legal or A4, it is necessary to set USE MP TRA Y to OFF on the F AX’S PRINTER SET menu.
5-38 F AX-L1000 Chapter 5: Appendix T urning on the P o wer 1. Connect the power cord to the power socket on the r ear of the fax unit. 2. Connect the other end of the power cord to the power sour ce. THE F AX MUST BE CONNECTED TO A PROPERL Y GROUNDED, THREE-PRONG 200 – 240 V AC OUTLET .
5-39 F AX-L1000 Chapter 5: Appendix INST ALL CARTRIDGE Y ou have not yet installed the toner cartridge. Install the FX6 toner car- tridge. REPLACE CARTRIDGE The toner cartridge has run out of toner . Replace the toner cartridge. CHECK PRINTER COVER The printer cover is not closed com- pletely .
5-40 F AX-L1000 Chapter 5: Appendix Pr ocessing When T rouble Occurs V ery rarely , during use the display may go out, all the ke ys stop working, or some other trouble occur because of intense noise or a strong shock. If such trouble occurs, perform an All Clear operation.
5-41 F AX-L1000 Chapter 5: Appendix Set the document COPY ST ART Copy oper ation COPY 01 XXXXXXXXXXX MEMOR Y IN USE X % DOCUMENT READ Y Star t/Scan Cop y 1.
5-42 F AX-L1000 Chapter 5: Appendix 1.6 Moving the Fax Unit Mo ving the F ax Unit The fax unit is heavy . Be sure to follow these general guidelines when lifting the fax to move it or to install the optional Paper Feed Unit (PF- 52), etc. ❏ Moving the fax unit requir es two people.
5-43 F AX-L1000 Chapter 5: Appendix 2. SER VICE T OOLS 2.1 Printer Driver T ester 2.1.1 Outline Figure 5-3 Printer Dri ver T ester Printer driver tester is a special tool that operates the printer to check printer operations.
5-44 F AX-L1000 Chapter 5: Appendix 2.1.2 Explanation of LEDs and Switches Figure 5-4 LEDs and Switches LED1 to LED16 Monitors the state of the sensors and various status sent from the printer with the 16 LEDs. LED17 (Communication) Lights up when communicating with the printer .
5-45 F AX-L1000 Chapter 5: Appendix 2.1.3. Operation a) Connecting to the printer NO TE Before handling the printer dri ver tester , make sure to touch metallic parts of the printer to discharge electrical static as it may cause malfunctions or failures in the printer and the tester .
5-46 F AX-L1000 Chapter 5: Appendix b) Setting the printer operations T able 5-1 shows printer operations that can be set by combinations of switches on the printer dri ver tester . Set the operation mode with SW1 and SW2 and various data with SW3 to SW9 according to the table 5-1.
5-47 F AX-L1000 Chapter 5: Appendix T able 5-1 Printer Operation Setting NO TE T o set the printer to enter ready inhibit mode at power -ON, set the mode using the switches and then turn ON the printer while holding SW11 to “1”.
5-48 F AX-L1000 Chapter 5: Appendix c) Monitoring the printer condition Select items to monitor from the table 5-2 and 5-3. Make settings with SW12 to SW14 and monitor the printer condition with LED1 to LED16.
5-49 F AX-L1000 Chapter 5: Appendix T able 5-3 Printer Condition (2) NO TE 1. The specif ied pick-up source was eliminated from the pick-up unit configuration. 2. Any of the follo wing four has taken a place. • The specif ied deli very unit was eliminated from the deliv ery unit configuration.
5-50 F AX-L1000 Chapter 5: Appendix • T wo sheets of paper are fed to the duple xing unit when the duple x deli v ery has been selected. • The duplexing unit was eliminated from the delivery unit configuration when the option delivery slot has been selected.
5-51 F AX-L1000 Chapter 5: Appendix 3. OPTION 3.1 Option Memory VII (4M-BYTE) 3.1.1 Safety and precautions Damage due to electrostatic discharge Electrostatic charge in the human body is the cause of damage to electronic parts as well as changes in their characteristics.
5-52 F AX-L1000 Chapter 5: Appendix b) Installation b-1) Unpacking Check that the box contains the memory board. b-2) Preparation Perform the operations below before attaching the memory boards. (1) Output all image data if there is any remaining in image memory .
5-53 F AX-L1000 Chapter 5: Appendix b-3) Attaching memory boards (1) T o disable memory backup, remo ve the jumper plug on the SCNT board jumper switch (JP1).
5-54 F AX-L1000 Chapter 5: Appendix (2) T o install the first DRAM board, follo w the steps q and w sho wn belo w . T o install the second DRAM board, follow the steps e and r sho wn below .
5-55 F AX-L1000 Chapter 5: Appendix b-4) Check after DRAM boards installation After installing the DRAM boards, carry out the following procedure to ensure that the DRAM boards are properly identified by the fax. (1) Referring to the flow chart, enter test mode D-RAM test [1].
5-56 F AX-L1000 Chapter 5: Appendix b-5) Removing the memory boar d When removing the memory board, perform the steps in b-3) Attaching memor y boards in re v erse order . Be sure to remov e the memory board only after turning the po wer off and removing the jumper plug on SCNT board jumper switch (JP1).
5-57 F AX-L1000 Chapter 5: Appendix 3.1.3 T echnical information a) Configuration and construction 1. Product name OPTION MEMOR Y VII (4MB) 2. External view Figure 5-13 DRAM Board (4MB) b) Specificati.
5-58 F AX-L1000 Chapter 5: Appendix 3.1.4 Maintenance and service a) T roubleshooting The fax does not recognize the DRAM boards even when the test mode D- RAM test is executed. Solutions: (1) Check that the DRAM boards are securely connected. (2) Replace the DRAM board.
5-59 F AX-L1000 Chapter 5: Appendix SCNT board (J1) ,/ Memory board J1 Memory Signal name Description A33 . 33 N.C Not connected A34 . 34 N.C Not connected A35 . 35 VD15 Data signal A36 . 36 N.C Not connected A37 . 37 VD0 Data signal A38 . 38 VD1 Data signal A39 .
5-60 F AX-L1000 Chapter 5: Appendix NO TE The J1 connector on the SCNT board has two ro ws A and B and has a total of 144 pins. Since ro ws A and B hav e similar pin layout , only different pins are s.
5-61 F AX-L1000 Chapter 5: Appendix 3.2 V erification Stamp Unit 3.2.1 Service operations a) External View Figure 5-14 Exter nal V iew b) Installation b-1) Unpacking Check that the box contains the stamp unit and one screw . b-2) Attachment to the main unit (1) Disconnect the power cord of the fax unit at the power source.
5-62 F AX-L1000 Chapter 5: Appendix (3) Remov e the three scre ws, and remove the lo wer reader cover . Figure 5-16 Attachment to the Main Unit 2 (4) Connect the stamp unit connector cable to the main unit, and fasten the stamp unit with the one scre w as sho wn belo w .
5-63 F AX-L1000 Chapter 5: Appendix (5) Remove the cap from the stamp unit. Figure 5-18 Attachment to the Main Unit 4 (6) Fasten the lower reader cover in place with the three screws. (7) Place the end of the stopper over the end of the stub so it locks in place, and close the upper reader frame.
5-64 F AX-L1000 Chapter 5: Appendix (9) In the service mode, set #1SSSW SW06 Bit3 to 1. Figure 5-20 Flo wchart of Changing SSSW b-3) Operation check After setting 8.
5-65 F AX-L1000 Chapter 5: Appendix 3.2.2 Maintenance and service a) Signal description ST AMP unit ,/ ,/ ,/ ,/ ,/ SCNT board (J8) Stamp J8 Signal name Description 1 , 1 ST AMP+24V ST AMP+24V 2 , 2 ST.
5-66 F AX-L1000 Chapter 5: Appendix 3.3 Paper Feed Unit PF-52 3.3.1 Safety and precautions a) Personal precautions During servicing, if you ha ve to operate the sensor arm, be careful to keep hair , clothes, accessories, etc. from becoming wrapped up in moving and rotating parts.
5-67 F AX-L1000 Chapter 5: Appendix 3.3.2 Service operations a) External Views Figure 5-22 Exter nal V iew.
5-68 F AX-L1000 Chapter 5: Appendix b) Installation b-1) Unpacking REFERENCE Please refer to item Installing Paper Feed Unit (PF-52) in this Chapter , 1.4 Assembling the Fax , for installation. b-2) Attachment to the main unit REFERENCE Please refer to item Installing Paper Feed Unit (PF-52) in this Chapter , 1.
5-69 F AX-L1000 Chapter 5: Appendix b-3) Cassette installation (1) When you plug the power cord into a sock et, “ SUPPL Y REC. P APER ” is displayed and the Alarm lamp blinks.
5-70 F AX-L1000 Chapter 5: Appendix 3.3.3 T echnical information a) Configuration and construction External structure Item Dimensions and weight Remarks Dimensions 15.35" (W) × 19.41" (D) × 4.96" (H) W ith cassette (390 × 493 × 126 mm) W eight approx.
5-71 F AX-L1000 Chapter 5: Appendix b) Specifications Recording paper dimensions Letter 8.50"(W) × 10.98"(L) (216 × 279 mm) Lega l 8.50"(W) × 14.00"(L) (216 × 356 mm) A4 8.27"(W) × 11.69"(L) (210 × 297 mm) B5-JIS 7.
5-72 F AX-L1000 Chapter 5: Appendix 3.3.4 Operations a) Functions a-1) Recording paper pickup function The paper feeder is dri v en by the main motor of the fax via the gear . When the nPRNT signal is sent to the ECNT board from the SCNT board, the main motor of the printer starts rotation.
5-73 F AX-L1000 Chapter 5: Appendix c) Arrangement of switches Figure 5-26 Arrangement of Switches P ape r size SW801 SW802 SW803 No cassette LEGAL Ex ecutiv e LETTER Other Custom B5 A4 OFF OFF OFF OFF ON ON ON ON OFF OFF ON ON OFF OFF ON ON OFF ON OFF ON OFF ON OFF ON (Av ailable f or pr inter function.
5-74 F AX-L1000 Chapter 5: Appendix d) Electrical circuit section The operation sequences of the paper feeder are controlled by the paper feeder dri ver . A 4- bit microprocessor is used in the paper feeder dri ver , which controls the sequences of the paper feeder and the serial communication with the engine controller (ECNT board) of this fax.
5-75 F AX-L1000 Chapter 5: Appendix 3.3.5 Maintenance and service a) T roubleshooting The fax main unit does not detect that the P APER FEED UNIT PF-52 is mounted. Solutions: ( 1 ) Check the connection between the main unit and the paper size detection board 2.
5-76 F AX-L1000 Chapter 5: Appendix b) Signal description P aper size detection board 2 (J801) ,/ P aper siz e detection board 1 (J601) J801 J601 Signal name Description 1 / 6 +24V Paper feeder unit dri v e v oltage 2 , 5 nSEL1 Paper feed select signal 3 .
5-77 F AX-L1000 Chapter 5: Appendix 3.3.6 Recor ding P aper Size Priority a) Cassette selection switches Here are the two cassette selection switch items. Switch A: divided recording Enables/disables recording of received images onto recording paper with a length shorter than the received/copied length.
5-78 F AX-L1000 Chapter 5: Appendix b) Reading the recording paper size table When the recording paper size is determined with reduction, the combination of user data cassette selection switches A and B determine the priority order for the recording paper actually printed and the contents of printing.
5-79 F AX-L1000 Chapter 5: Appendix c) Printed recording paper table Reception image siz e: A4 Cassette switches A B A4/Letter Letter/Legal OFF OFF 1) Actual size 1) Automatic reduction (A4) (Letter) .
5-80 F AX-L1000 Chapter 5: Appendix Reception image siz e: Legal Cassette switches A B A4/Letter Letter/Legal OFF OFF 1) Automatic reduction 1) Actual size (A4) (Legal) 2) Automatic reduction 2) Autom.
5-81 F AX-L1000 Chapter 5: Appendix 3.4 Envelope Feeder EF-52 3.4.1 Service operations a) External Views Figure 5-29 Exter nal V iew b) Installtion b-1) Unpacking Check that the box contains the en velope feeder . b-2) Attachment to main unit (1) Open the envelope feeder packaging.
5-82 F AX-L1000 Chapter 5: Appendix 3.4.2 T echnical information a) Configrution and construction External structure Item Dimensions and weight Dimensions 12.91" (W) × 13.94" (D) × 4.45" (H) (328 × 354 × 113 mm) W eight approx.4.85 lbs (2.
5-83 F AX-L1000 Chapter 5: Appendix 3.4.3 Operation a) Function a-1) Paper pickup function The pick-up roller , feed roller , and separation roller are rotated sequentially by the main motor rotation, and an en velope is picked up.
5-84 F AX-L1000 Chapter 5: Appendix c) Arrangement of sensors Figure 5-33 Arrangement of Sensors d) Electrical circuit section The signal detect by the en velope multiple feed sensor , en v elope sensor and en velope pick- up solenoid, are sent ECNT board via the envelope feeder driver PCB.
5-85 F AX-L1000 Chapter 5: Appendix 3.4.4 Maintenance and service a) T roubleshooting a-1) Paper jam troubleshooting <Possible causes> 1.W arped or twisted en velope Action: Straighten the warped or twisted en velope, and then instruct the user .
5-86 F AX-L1000 Chapter 5: Appendix a-2) Malfunction status troubleshooting “5F-61 ERROR” (Envelope Option error) <Possible causes> 1. Defective envelope feeder connector Action: Remov e the en velope feeder from the fax and check the connector .
5-87 F AX-L1000 Chapter 5: Appendix b) Signal description En velope feeder(J901) ,/ ECNT board (J911) J901 J911 Signal name Description .. 4 N.C Not connected 1 / 3 +24V Envelope feeder drive voltage 2 , 2 nSEL2 Envelope feeder select signal 3 . 1 DGND Ground Envelope feeder(J901) ,/ ECNT board (J912) J901 J912 Signal name Description 4 .
5-88 F AX-L1000 Chapter 5: Appendix 3.4.5 Installation P osition Adjustment of Separation Guide of Envelope Feeder (adjustment of gap between separation guide and lower separation roller) a) When Normally , the separation guide and the top co ver of the en velope feeder must be remo v ed as one.
5-89 F AX-L1000 Chapter 5: Appendix 3.4.6 Installation P osition Adjustment of En velope Multiple Feed Sensor a) When The installation position of envelope multiple feed sensor is normally adjusted at the factory .
5-90 F AX-L1000 Chapter 5: Appendix Figure 5-36 Adjustment of En velope Multiple F eed Sensor Screw Env elope multiple feed sensor Connecting to the multiple f eed sensor connecter. Printer driver tester (RY9-0124) Sensor T est LED Connecting to the printer's connector f or the envelope feeder.
5-91 F AX-L1000 Chapter 5: Appendix 3.5 Duplex Unit DU-52 3.5.1 Service operations a) External Views Figure 5-37 Exter nal V iew b) Installtion b-1) Unpacking Check that the box contains the duplexing feeder . b-2) Attachment to main unit (1) Open the duplexing unit packaging.
5-92 F AX-L1000 Chapter 5: Appendix 3.5.2 T echnical information a) Configration and construction External structure Item Dimensions and weight Dimensions 12.56" (W) × 14.17" (D) × 5.55" (H) (319 × 360 × 141 mm) W eight approx. 7.72 lbs (3.
5-93 F AX-L1000 Chapter 5: Appendix 3.5.3 Operation a) Function a-1) Reversing function When the duplexing unit receives the duplexing unit command from the fax, it turns ON the duplexing unit solenoid, moves the face-up deflector and feeds the paper to the duplexing unit.
5-94 F AX-L1000 Chapter 5: Appendix a-3) Paper jam detection The following paper sensors are installed to detect whether the paper is present or not and whether the paper is fed normally or not.
5-95 F AX-L1000 Chapter 5: Appendix b) Structure The paper is led to the duplexing unit by the f ace-up deflector . This f ace-up deflector mov es in conjunction with the f ace-up tray , ho we ver , it moves by the duple xing unit solenoid (SL701) when the face-up tray is closed.
5-96 F AX-L1000 Chapter 5: Appendix c) Arrangement of sensors Figure 5-41 Arrangement of Sensors PS701 PS703 PS702.
5-97 F AX-L1000 Chapter 5: Appendix d) Electrical circuit section The signal detect by the duplexing unit pick-up sensor , face-up sensor and re versed paper sensor , are sent ECNT board via the duplexing unit dri ver PCB. Figure 5-42 Electrical Cir cuit Section Duple xing unit dr iver PCB Accepts the command when "L.
5-98 F AX-L1000 Chapter 5: Appendix 3.5.4 Maintenance and service a) T roubleshooting a-1) Paper jam troubleshooting <Possible causes> 1. Paper is curled due to having been left for a long time. Action: Straighten the paper , and then instruct the user .
5-99 F AX-L1000 Chapter 5: Appendix 14. Defectiv e F AX-L1000 Printer kit Action: Replace the F AX-L1000 Printer kit. a-2) Malfunction status troubleshooting "5F-56 ERROR" (Duplexing unit exhaust fan (FM701) malfunction) <Possible causes> 1.
5-100 F AX-L1000 Chapter 5: Appendix "DUPLEX JAM" message appears when the paper jam has not occurred; so, the fax cannot be in READY mode. <Possible causes> 1. Rev ersing paper sensor lev er does not mov e smoothly , or is damaged. Action: Set the lev er to mo ve smoothly .
5-101 F AX-L1000 Chapter 5: Appendix Duplexing unit(J702) ,/ Duplex feed motor J701 Motor Signal name Description 1 / 1 FMT A Duplex feed motor drive signal 2 / 2 nFMT A Duplex feed motor drive signal.
5-102 F AX-L1000 Chapter 5: Appendix Duplexing unit(J707) ,/ Duplexing unit exhaust fan J707 Fan Signal name Description 1 / 1 F ON Duplexing unit fan drive signal 2 , 2 F LOCK Duplexing unit fan lock detection signal 3 .
5-103 F AX-L1000 Chapter 5: Appendix 3.6 F AX-L1000 ISDN Kit 3.6.1 Safety and precautions Damage due to electrostatic discharge Electrostatic charge in the human body is the cause of damage to electronic parts as well as changes in their characteristics.
5-104 F AX-L1000 Chapter 5: Appendix b) Installation b-1) Unpacking Check that the box contains the F AX-L1000 ISDN Kit, cables, ROM, modular spacers and four screws. b-2) Preparation Perform the operations below before attaching the kit. (1) Disconnect the modular jack cord (telephone line) from the fax.
5-105 F AX-L1000 Chapter 5: Appendix (6) Refer to Figure 5-43 and bend cables 1 and 2 as shown in order to make insertion of the kit easier . (7) Insert cables 1 and 2 into J2 and J1 on the G4 board ass’y . (8) Insert the connectors of cable 3 into J1 and J2 on the G4 relay board unit.
5-106 F AX-L1000 Chapter 5: Appendix (10) Remove the seven screws. (11) Disconnect the connectors of the option from J33, J34, J35 and J40 on the TWINS board. Then, remo v e the option. Figure 5-47 Pr eparation for Installation 3B (12) Remove the two screws and remove the shield cover 2.
5-107 F AX-L1000 Chapter 5: Appendix b-3) Attaching the kit (1) Insert the kit, aligning the tabs with the slots on the main unit. (2) After inserting the kit, insert cables 1, 2 and 3 into J37, J39 and J43 on the TWINS board. (3) Fasten the kit in place with the 4 included screws.
5-108 F AX-L1000 Chapter 5: Appendix If a F AX-L1000 Printer Kit (Option) is installed proceed to step (5). (4) Fasten the shield cover in place with the six screws.
5-109 F AX-L1000 Chapter 5: Appendix b-4) Replacing the ROM (1) Remov e the six scre ws and remo ve the shield cov er . Figure 5-51 R OM Replacement 1 (2) Remov e the R OM on the SCNT board using the IC-Removing T ool (HY9-0022).
5-110 F AX-L1000 Chapter 5: Appendix (4) Fasten the shield cover of the SCNT board in place with the six screws. (5) Fasten the right co v er in place with the one scre w . (6) Attach the modular spacers into the extension phone jack and telephone line jack.
5-111 F AX-L1000 Chapter 5: Appendix b-6) Check after the Kit Installation After installing the kit, carry out the following procedure to ensure that the kit is properly identified by the main unit. (1) Referring to the flow chart, enter service data registration, then check that the ROM versions are displayed.
5-112 F AX-L1000 Chapter 5: Appendix 3.6.3 T echnical information a) Configuration and construction 1. Product names F AX-L1000 ISDN KIT 2. External view Figure 5-55 Exter nal V iew 1 1.
5-113 F AX-L1000 Chapter 5: Appendix b) Specifications Dimensions 11.06" (W) × 9.70" (D) × 1.65" (H) (281mm × 246.5mm × 42mm) W eight Approx. 2.20 lbs (1.0 kg) Applicable lines Euro-ISDN Communication method Half-duplex Communication control protocol ITU-T T .
5-114 F AX-L1000 Chapter 5: Appendix Time required for transmission pr otocol Post-message Post-message Pre-message Protocol *2 Protocol *3 Mode Protocol *1 (between pages) (after pages) G4 Approx. 1.1 s Approx. 1 s Approx. 0.6 s *1 T ime from when other facsimile is connected to the line until image transmission be gins.
5-115 F AX-L1000 Chapter 5: Appendix c) Service soft switch #4C ISDN (ISDN settings) ISDN BASIC Bitswitch SW01 Bit Function 1 0 0 Not used 1 Not used 2 Not used 3 Not used 4 Progress Indicator informtion Add Don’t Add element for outgoing Speech calls 5 Progress Indicator informtion Add Don’t Add element for outgoing 3.
5-116 F AX-L1000 Chapter 5: Appendix ISDN BASIC Bitswitch SW02 Bit Function 1 0 0 Not used 1 Send RELCOMP message Ye s No when incoming call is rejected 2 G4/G3 automatic fallback No Ye s 3 3.
5-117 F AX-L1000 Chapter 5: Appendix ISDN BASIC Bitswitch SW03 Bit Function 1 0 0 Outgoing TEL call bearer 3.1kHz audio SpeechNot used capability 1 Not used 2 Outgoing G4 call HLC Don’t Add Add 3 Ac.
5-118 F AX-L1000 Chapter 5: Appendix [Bit 6] In the conditions for enforced G4/G3 fallback, it is possible to select whether or not to add "Does the error code set in the fallback table coincide .
5-119 F AX-L1000 Chapter 5: Appendix ISDN BASIC Bitswitch SW06 Bit Function 1 0 0 Sending Complete information Add Don’t Add element 1 Not used 2 Not used 3 Not used 4 Not used 5 Not used 6 LLC info.
5-120 F AX-L1000 Chapter 5: Appendix ISDN BASIC Bitswitch SW08 Bit Function 1 0 0 Not used 1 Not used 2 Outgoing G3 call HLC Don’t Add Add 3 Not used 4 enforced G4/G3 fallback Ye s No 5 Calling Part.
5-121 F AX-L1000 Chapter 5: Appendix ISDN BASIC Bitswitch SW13 Bit Function 1 0 0 Not Used 1 Not Used 2 Bearer Capability of ON-HOOK call Speech 3.1kHz-audio 3 Not used 4 Not Used 5 Not Used 6 Incoming address check for Don’t respond Respond global number incoming calls 7 Not used [Bit 2] It is possible to set either “ Speech ” or “ 3.
5-122 F AX-L1000 Chapter 5: Appendix ISDN BASIC Numeric parameter No. Function Selecting range Default setting 16 F allbac k W ait Time 0-255 ( × 100msec.) 0 (0msec.) 18 progress description of 0-127 3 3.1kHz-audio call-time 19 progress description of 0-127 3 speech call-time [No.
5-123 F AX-L1000 Chapter 5: Appendix ISDN BASIC Redial Code No. Function Selecting range Default setting 01-128 Redial 1001-1131 See d) SSSW default setting ISDN BASIC G4/G3 Fallback No. Function Selecting range Default setting 01-128 G4/G3 fallback 1001-1131 See d) SSSW default setting ISDN BASIC Speech Fallback No.
5-124 F AX-L1000 Chapter 5: Appendix Example) G4/G3 Fallbac k function and operation pr ocedure • In the case where the F AX-L1000 makes on outgoing G4 call to a G3 machine a) After the F AX-L1000 sends the SETUP message which includes the Bearer Capability information element “unrestricted digital.
5-125 F AX-L1000 Chapter 5: Appendix b) Next, the 4 digits “1088” of the service error code “##1088” are registered in service data #4C ISDN BASIC G4/G3 Fallback , and another outgoing call is made to the G4.
5-126 F AX-L1000 Chapter 5: Appendix ISDN G4 Bitswitch SW01 Bit Function 1 0 0 Not used 1 Not used 2 Not used 3 Multi-document transmission Y e s No 4 Not used 5 Not used 6 G4 B-channel communication .
5-127 F AX-L1000 Chapter 5: Appendix ISDN G3 Bitswitch SW01 Bit Function 1 0 0 Enforced G3 calling Y e s No 1 Not used 2 Not used 3 Not used 4 Not used 5 Not used 6 Not used 7 Not used [Bit0] For all outgoing calls, it is possible to set whether or not to enforce G3 calling.
5-128 F AX-L1000 Chapter 5: Appendix d) SSSW default setting TYPE EUROPE GERMAN IT A L Y FRANCE #4C ISDN ISDN BASIC Bitswitch SW01 00100000 00100000 00100000 00100000 SW02 01100011 01100011 11100011 0.
5-129 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 2 5 : 0000 2 6 : 0000 2 7 : 0000 2 8 : 0000 2 9 : 0000 3 0 : 0000 3 1 : 0000 3 2 : 0000 3 3 :.
5-130 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 6 8 : 0000 6 9 : 0000 7 0 : 0000 7 1 : 0000 7 2 : 0000 7 3 : 0000 7 4 : 0000 7 5 : 0000 7 6 :.
5-131 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 111: 0000 112: 0000 113: 0000 114: 0000 115: 0000 116: 0000 117: 0000 118: 0000 119: 0000 120.
5-132 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 23: 1025 1025 1025 1025 24: 1026 1026 1026 1026 25: 1027 1027 1027 1027 26: 1028 1028 1028 10.
5-133 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 66: 1070 1070 1070 1070 67: 1071 1071 1071 1071 68: 1072 1072 1072 1072 69: 1073 1073 1073 10.
5-134 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 109: 1113 1113 1113 1113 110: 1114 1114 1114 1114 111: 1115 1115 1115 1115 112: 1116 1116 111.
5-135 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 21: 1023 1023 1023 1023 22: 1024 1024 1024 1024 23: 1025 1025 1025 1025 24: 1026 1026 1026 10.
5-136 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 64: 1068 1068 1068 1068 65: 1069 1069 1069 1069 66: 1070 1070 1070 1070 67: 1071 1071 1071 10.
5-137 F AX-L1000 Chapter 5: Appendix d) SSSW default setting (Continue) TYPE EUROPE GERMAN IT A L Y FRANCE 107: 1111 1111 1111 1111 108: 1112 1112 1112 1112 109: 1113 1113 1113 1113 110: 1114 1114 111.
5-138 F AX-L1000 Chapter 5: Appendix e) Report and List e-1) System data list This list shows service data settings of service soft switches and service parameters.
5-139 F AX-L1000 Chapter 5: Appendix Figure 5-59 System Data List (2/10).
5-140 F AX-L1000 Chapter 5: Appendix Figure 5-60 System Data List (3/10).
5-141 F AX-L1000 Chapter 5: Appendix Figure 5-61 System Data List (4/10).
5-142 F AX-L1000 Chapter 5: Appendix Figure 5-62 System Data List (5/10).
5-143 F AX-L1000 Chapter 5: Appendix Figure 5-63 System Data List (6/10).
5-144 F AX-L1000 Chapter 5: Appendix Figure 5-64 System Data List (7/10).
5-145 F AX-L1000 Chapter 5: Appendix Figure 5-65 System Data List (8/10).
5-146 F AX-L1000 Chapter 5: Appendix Figure 5-66 System Data List (9/10).
5-147 F AX-L1000 Chapter 5: Appendix Figure 5-67 System Data List (10/10).
5-148 F AX-L1000 Chapter 5: Appendix e-2) System dump list This list sho ws the past communications statuses and error communications history . Figure 5-68 System Dump List (1/3).
5-149 F AX-L1000 Chapter 5: Appendix Figure 5-69 System Dump List (2/3).
5-150 F AX-L1000 Chapter 5: Appendix Displays error information for the 3 most recent communication. Figure 5-70 System Dump List (3/3).
5-151 F AX-L1000 Chapter 5: Appendix e-4) Dch log report This list sho ws the D-channel communication history . Up to the latest 32 messages can be displayed.
5-152 F AX-L1000 Chapter 5: Appendix •How to View the Dch dump list a) Title Column *1: Date and T ime. *2: Elapsed time since the power was turned ON (msec.). Increases every 5 msec.. *3: Message direction. TX> : The message the machine sent <RX : The message the netw ork sent *4: Message Name.
5-153 F AX-L1000 Chapter 5: Appendix c-2) V ariable Length Information Elements The main information element is composed of an information element identifier (1 octet), an length of contents of inform.
5-154 F AX-L1000 Chapter 5: Appendix “ 90 ”: 3.1kHz audio “ 80 ”: Speech •High Layer Compatibility ( * 13) Number 1 octet : “ 7D ” Number 4 octet : High layer characteristics identificat.
5-155 F AX-L1000 Chapter 5: Appendix e-4) Bch Log report This report shows B-channel communication histo y . Up to the latest 3 communications can be displayed Figure 5-72 Bch Log Report ∗ 5 ∗ 8 .
5-156 F AX-L1000 Chapter 5: Appendix •How to View the Bch dump list a) Title Column *1: Communication Number . *2: Error Code. “None” will be shown for normal communications. *3: When B-channel communication has commenced. *4: When B-channel communication has completed.
5-157 F AX-L1000 Chapter 5: Appendix 3.6.4 G4 board components Fig. 5-73 Component bloock diagram a) DTMF signal detection circuit This circuit uses a dedicated IC (IC38 DTMF receiver) to detect a DTMF signal.
5-158 F AX-L1000 Chapter 5: Appendix e) PCM CODEC IC (IC50) This IC converts receive signals (digital signals through ISDN lines) to analog signals. It converts transmit signals (analog audio signals) to digital signals. f) Slave CPU (IC21) The slav e CPU, NEC-made uPD70F3025A GC-33 (V .
5-159 F AX-L1000 Chapter 5: Appendix 3.6.5 Flow of Image Signals a) T ransmission Figure 5-74 T ransmission Image Signal Flow (2) IC22 A:Image processing IC B:CODEC IC C:DRAM D:TWINS IC E:DRAM F:Slav .
5-160 F AX-L1000 Chapter 5: Appendix (1) The image is scanned by the contact sensor , and the analog image data is sent to the SCNT board. (2) The image processing IC (IC20) converts the analog image data from the contact sensor into digital data.
5-161 F AX-L1000 Chapter 5: Appendix b) Reception Figure 5-75 Reception Image Signal Flow (5) IC22 A:Image processing IC B:CODEC IC C:DRAM D:TWINS IC E:DRAM F:Slav e CPU G:ISDN interf ace IC (4) IC20 .
5-162 F AX-L1000 Chapter 5: Appendix ( 1 ) The receiv ed data is sent to the slav e CPU from the modular board of the F AX-L1000 ISDN KIT through the ISDN interface IC.
5-163 F AX-L1000 Chapter 5: Appendix 3.6.6 ISDN Protocol Messages Main messages which are used in the communication protocols of Layer 2 - Layer 3 of the control channel’ s D-channel and Layer 2 - Layer 6 of the information channel’ s B-channel are listed.
5-164 F AX-L1000 Chapter 5: Appendix Layer 3 (Continue) Message Description Remark REL Release Sent when layer 3 is released or when DISC is received. REL COMP Release Complete Sent when REL is received.
5-165 F AX-L1000 Chapter 5: Appendix Layer 5 Message Description Remark CSS Command Session Start The first thing sent when layer 5 is started. Canon mode communication parameters are mainly added to this command. RSSP Response Session Start Sent when CSS is received and layer 5 can Positive be started.
5-166 F AX-L1000 Chapter 5: Appendix Layer 5 (Continue) Message Description Remark CDCL Command Document Indicates the function of the sending side Capability List (page size, resolution). RDCLP Response Document Indicates the function of the receiving side Capability List Positive (page size, resolution).
5-167 F AX-L1000 Chapter 5: Appendix c) D-Channel Standard Protocol Figure 5-76 D-Channel Pr otocol Flow UA DISC REL COMP REL DISC CONN A CK CONN (ALERT) * UA SABME (CALL PROC) * SETUP Calling par ty .
5-168 F AX-L1000 Chapter 5: Appendix d) Information elements in the SETUP message The SETUP message is one of the messages used in the D-channel Layer 3 communication protocol, as opposed to a network, and requires commencement of call settings.
5-169 F AX-L1000 Chapter 5: Appendix High Layer Compatibility W ith an outgoing G4 call, “G4 F AX” is set, with an outgoing G3 call, “G2/G3 F AX”, and with telephone, “TEL”. (There is no telephone in this machine.) Addition of this required information is handled as an option in ITU-T recommendations.
5-170 F AX-L1000 Chapter 5: Appendix f) B-Channel Standard Protocol (G3) Figure 5-78 B-Channel Pr otocol Flow (G3) T ransmitter Receiv er CNG CED DIS DCS TFC CFR Messege MPS MCF Messege EOP La yer 6 L.
5-171 F AX-L1000 Chapter 5: Appendix 3.6.7 Maintenance and service a) T roubleshooting The fax does not recognize the F AX-L1000 ISDN KIT even when it is attached properl y . Solutions: (1) Check that the kit is securely connected. (2) Replace the kit.
5-172 F AX-L1000 Chapter 5: Appendix ##1002 [TX/RX] No route to specified transit network. Cause: Indicated above Solutions: ( 1 ) Re-check the method of connection to the designated relay network. (2) Output a communications analysis list, and analyze it.
5-173 F AX-L1000 Chapter 5: Appendix ##1007 [TX/RX] a ) Call awarded and being delivered in an established channel. b) Call identity not exist. Cause a): Indicated above Solutions a): (1) W ait a while, then r e-establish communication. (2) Output a communications analysis list, and analyze it.
5-174 F AX-L1000 Chapter 5: Appendix ##1016 [TX/RX] a) Normal call clearing user busy . b) No basic channel free. Cause a): Indicated above Solutions a): (1) Re-establish communication.
5-175 F AX-L1000 Chapter 5: Appendix ##1018 [TX/RX] No user responding Cause: Indicated abov e Solutions: (1) Re-transmit. (2) Make sure that the other party’ s machine is plugged in and connected to the line. (3) Output a communications analysis list, and analyze it.
5-176 F AX-L1000 Chapter 5: Appendix ##1026 [TX/RX]`Non-selected user cleaning. Cause: Indicated abov e Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-177 F AX-L1000 Chapter 5: Appendix ##1030 [TX/RX] Response to status enquiry . Cause: Indicated abov e Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-178 F AX-L1000 Chapter 5: Appendix ##1034 [TX/RX] a) No circuit/channel available b) No access to a closed user gr oup. Cause a): Indicated abov e Solutions a): (1) W ait a while, then re-transmit, because the other party’ s machine is b usy . (2) Output a communications analysis list, and analyze it.
5-179 F AX-L1000 Chapter 5: Appendix ##1041 [TX/RX] T emporary failure Cause: Indicated abov e Solutions: (1) W ait a while, then re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-180 F AX-L1000 Chapter 5: Appendix ##1047 [TX/RX] Resources unavailable, unspecified Cause: Indicated abov e Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-181 F AX-L1000 Chapter 5: Appendix ##1056 [TX/RX] The calling number of the wished connection has been changed Cause: Indicated abov e Solutions: (1) Re-check the telephone number , then re-transmit. (2) Output a communications analysis list, and analyze it.
5-182 F AX-L1000 Chapter 5: Appendix ##1058 [TX/RX] a) Bearer capability not presently available b) Call has not been accessed, break down through time-out Cause a): Indicated above Solutions a): (1) Re-check the contract, and re-transmit. (2) Output a communications analysis list, and analyze it.
5-183 F AX-L1000 Chapter 5: Appendix ##1061 [TX/RX] Called party is closed or does not support the service Cause: Indicated abov e Solutions: (1) Designated number/Re-check the contract, and re-transmit. (2) Output a communications analysis list, and analyze it.
5-184 F AX-L1000 Chapter 5: Appendix ##1065 [TX/RX] Bearer capability not implemented Cause: Indicated abov e Solutions: (1) Re-check the designated service contract, and re-transmit.
5-185 F AX-L1000 Chapter 5: Appendix ##1079 [TX/RX] Service or option not implemented, unspecified Cause: Indicated abov e Solutions: (1) Re-check the designated service contract, and re-establish communication. (2) Output a communications analysis list, and analyze it.
5-186 F AX-L1000 Chapter 5: Appendix ##1084 [TX/RX] Call identity in use Cause: Indicated abov e Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-187 F AX-L1000 Chapter 5: Appendix ##1089 [TX/RX] Line busy Cause: Indicated abov e Solutions: (1) Re-transmit. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-188 F AX-L1000 Chapter 5: Appendix ##1095 [TX/RX] Invalid message, unspecified Cause: Indicated abov e Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-189 F AX-L1000 Chapter 5: Appendix ##1099 [TX/RX] Information element non-existent or not implemented Cause: Indicated above Solutions: (1) Re-establish communication.
5-190 F AX-L1000 Chapter 5: Appendix ##1103 [TX/RX] Disconnection from network Cause: Indicated above Solutions: (1) Re-check the phone number and try the call again.
5-191 F AX-L1000 Chapter 5: Appendix ##1113 [TX/RX] a) Release because of error in a distant area b) Disconnection from network Cause a): Indicated above Solutions a): (1) Re-establish communication. (2) Output a communications analysis list, and analyze it.
5-192 F AX-L1000 Chapter 5: Appendix ##1127 [TX/RX] Interworking, unspecified Cause: Indicated abov e Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it. (3 ) Make sure the 4 digits of the applicable error code are registered in #4C ISDN BASIC, [G4/G3 Fallback] and [Speech Fallback] .
5-193 F AX-L1000 Chapter 5: Appendix • B-channel error codes ##1255 [RX] B-channel was disconnected without the document being started Cause: After the negotiation procedure on the transmitting side, a disconnection occurred without the document being transmitted.
5-194 F AX-L1000 Chapter 5: Appendix ##1334 [RX] Document attributes abnormal Cause: Attributes of the recei ved page such as size, resolution, and encoding method are abnormal. Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it.
5-195 F AX-L1000 Chapter 5: Appendix ##1348 [TX/RX] Session layer abnormal (Document procedure) Cause: Underfined document procedure frame recei ved with document properties Solutions: (1) Re-establish communication. (2) Output a communications analysis list, and analyze it.
5-196 F AX-L1000 Chapter 5: Appendix ##1372 [RX] CDS parameter abnormal Cause: Document procedures recei ved, abnormality disco v ered in CDS contents Solutions: (1) Hav e the document set properly on the transmitting side. (2) Output a communications analysis list, and analyze it.
5-197 F AX-L1000 Chapter 5: Appendix ##1389 [TX] RDCLP parameter abnormal Cause: Document procedures receiv ed, abnormality disco vered in RDCLP contents Solutions: (1) Check whether the transmitting machine has been stopped (2) Re-transmit. (3) Output a communications analysis list, and analyze it.
5-198 F AX-L1000 Chapter 5: Appendix ##1600 [RX] T ransmission err or in lay er 4 or below of B-channel Cause: Session procedures recei ved, abnormality disco vered in RSEP contents Solutions: (1) Re-transmit. (2) Output a communications analysis list, and analyze it.
5-199 F AX-L1000 Chapter 5: Appendix c) Communication problems • D-channel connection error (Service err or code “##1001~##1131”) (1) Set #4B ISDN BASIC Bitswitch SW03 bit2 to “1”. (2) Set #4B ISDN BASIC Bitswitch SW03 bit4 to “1”. (3) Set #4B ISDN BASIC Bitswitch SW03 bit5 to “0”.
5-200 F AX-L1000 Chapter 5: Appendix d) Signal discription ISDN G4 board (J1) ,/ ,/ ,/ ,/ ,/ TWINS board (J39) J1 J39 Signal name Description A1 , A20 nSTR OBE Strobe signal A2 . A19 PD0 Data signal A3 . A18 PD1 Data signal A4 . A17 PD2 Data signal A5 .
5-201 F AX-L1000 Chapter 5: Appendix ISDN G4 board(J2) ,/ ,/ ,/ ,/ ,/ TWINS board (J37) J2 J37 Signal name Description 1 . 14 GND Ground 2 , 13 +12V Logic drive voltage 3 . 12 GND Ground 4 . 1 1 GND Ground 5 , 10 +3.3V Logic drive voltage 6 , 9 +3.3V Logic drive voltage 7 .
5-202 F AX-L1000 Chapter 5: Appendix 3.7 F AX-L1000 Network Printer Upgrade kit 3.7.1 Safety and precautions Danger by Static Charge Static charge can change the electrical characteristics of the ethernet board or damage it. Do not handle the ethernet board under circumstances where static charge might occur easily .
5-203 F AX-L1000 Chapter 5: Appendix 3.7.3 T echnical information a) Specification Interf ace 10Base-T Ether net, 100Base-TX Ether net CPU TOSHIB A TMPR3904AF LAN controller TOSHIB A TC35815AF T ranscei ver TDK TSC78Q2120 Flash R OM 2MB DRAM 2MB × 2 Dimensions 139.
5-204 F AX-L1000 Chapter 5: Appendix c) Status LEDs Figure 5-80 Status LEDs • ER (Error) LED When the ethernet board is operating normally: ER may flash se veral times during initialization, then go of f. When the ethernet board is not operating normally: ER lights or flashes all the time.
5-205 F AX-L1000 Chapter 5: Appendix 3.7.4 Maintenance and Service a) T roubleshooting Every time the main unit is switched ON, the ethernet board automatically performs a self- diagnostic test. If the self-diagnostic test detects no errors, the LK LED lights and stays on.
5-206 F AX-L1000 Chapter 5: Appendix b) Connector locations Figure 5-81 Connector Locations J1(RJ45 connector) J3.
5-207 F AX-L1000 Chapter 5: Appendix c) Signal description Ethernet board(J1) ,/ Network J1 Network Signal name Description 1 / Network TX+ Send Data Line(+) 2 / Network TX- Send Data Line(-) 3 , Network RX+ Receive Data Line(+) 4 . Network N.C. Not used 5 .
5-208 F AX-L1000 Chapter 5: Appendix Ethernet board(J3) ,/ Adapter boar d connector(J2) J3 J2 Signal name Description B6 . B6 (Reserved) B7 . B7 GND Ground B8 . B8 D01 Data bit 1 B9 . B9 D03 Data bit 3 B10 . B10 D05 Data bit 5 B11 . B1 1 D07 Data bit 7 B12 .
5-209 F AX-L1000 Chapter 5: Appendix 3.8 F AX-L1000 P ostScript kit 3.8.1 Safety and precautions Danger by Static Charge Static charge can change the electrical characteristics of the DIMM or damage it. Do not handle the DIMM under circumstances where static charge might occur easily .
5-210 F AX-L1000 Chapter 5: Appendix b) Installation b-1) Unplug the power cord and r emove any interface cables fr om the rear of the printer . b-2) Remove the telephone line from the fax jack marked . b-3) Remove end of the handset connector cord fr om the extension phone jack marked and remove the handset from the handset cradle.
5-211 F AX-L1000 Chapter 5: Appendix b-6) Flip the top of the side cover outwards, then lift the cover slightly and remove it fr om the printer . b-7) Loosen the screw at the top of the memory slot cover . b-8) Swing open the cover and lift it off the printer .
5-212 F AX-L1000 Chapter 5: Appendix b-9) Remove the ROM DIMM from its packaging and insert it into the socket by pushing it into the middle of the three slots at the top right of the motherboard until it snaps into place. b-10) Place the memory slot cover back on the printer and close it.
5-213 F AX-L1000 Chapter 5: Appendix b-11) T ighten the screw at the top of the memory slot cover to secure it in position. b-12) Performing a Cold Reset. Please refer to 3.10.2 Ser vice Opera- tions: c) Cold Rest when performing a Cold Reset. NO TE • Replace the side cover after you have finished adding the DIMM boards.
5-214 F AX-L1000 Chapter 5: Appendix 3.8.3 T echnical Information a) Specifications T ype R OM DIMM, 72-pin Capacity 8MB Font 136fonts PDL Adobe PostScript Lev el 3 b) Operations This DIMM contains 136 types of PS fonts and a program to interpret PostScript Level 3 (PS).
5-215 F AX-L1000 Chapter 5: Appendix 3.9 RAM DIMM Module 3.9.1 Safety and precautions Danger by Static Charge Static charge can change the electrical characteristics of the DIMM or damage it. Do not handle the DIMM under circumstances where static charge might occur easily .
5-216 F AX-L1000 Chapter 5: Appendix b) Installation Please refer to F AX-L1000 PostScript Kit step b-8) for the procedures up to opening the side cov er .
5-217 F AX-L1000 Chapter 5: Appendix 3.9.3 T echnical informations a) Specifications T ype EDO RAM DIMM, 72-Pin Access time 60ns Capacity 4MB, 8MB, 16MB b) Operations This option memory is used to store print data, and it comes in several sizes:4MB, 8MB, and 16MB.
5-218 F AX-L1000 Chapter 5: Appendix 3.9.4 Maintenance and service a) T roubleshooting The main unit does not recognize the optional memory <Possible causes> 1.Defective optional memory Action: Replace the optional memory 2.Defective PDL board Action: Replace PDL board "OPTION RAM ERROR" <Possible causes> 1.
5-219 F AX-L1000 Chapter 5: Appendix 3.10 F AX-L1000 Printer kit 3.10.1 Safety and precautions When attaching this unit to the main unit, take care not to touch the hands with the power supply elements (heat sink, etc.). If the hands touch the elements, burns may result.
5-220 F AX-L1000 Chapter 5: Appendix Figure 5-85 Pr eparations for Installation 1 (4) Remov e the six scre ws and r emov e the shield cov er . Figure 5-86 Pr eparations for Installation 2 Right cov er.
5-221 F AX-L1000 Chapter 5: Appendix b-3) Attaching the option (1) Insert the option into the main unit. Attach the option by aligning it with the hooks in the circles in the figure and sliding it in the f igure indicated by the b lack arrow .
5-222 F AX-L1000 Chapter 5: Appendix Cold Reset may be any of the follo wing three types: •Cold Reset Used to rest all settings except the recording paper size under P A GE COUNT and TEST PRINT of TEST MENU back to their factory def ault settings.
5-223 F AX-L1000 Chapter 5: Appendix 3.10.3 T echnical informations a) Configuration and construction 1. Product name F AX-L1000 Printer kit 2. External view Figure 5-88 Exter nal V iew 7.
5-224 F AX-L1000 Chapter 5: Appendix b) Specifications Printing resolution 600/1200 dpi Printing speed (*1) Approx. 17 pages/min. (Letter , 600 dpi), about 8.5 pages/min. (Letter , 1200 dpi) Approx. 16 pages/min. (A4, 600 dpi), about 8 pages/min. (A4, 1200 dpi) First print time (*2) 15.
5-225 F AX-L1000 Chapter 5: Appendix P aper sizes Multi-purpose tray 98.4mm (W) × 190mm (L)(min.) ~ 216mm (W) × 356mm (L) (max.) size plain paper (60g/m 2 ~ 128g/m 2 recommended paper), abov e-menti.
5-226 F AX-L1000 Chapter 5: Appendix ROM DIMM soc ket 3 RAM DIMM socket 2 Host interface Standard: IEEE 1284 parallel interface Option: expansion interf ace (10B ASE-T , 100B ASE-TX) Language Standard.
5-227 F AX-L1000 Chapter 5: Appendix c) Overview •High speed printing Equipped with the Intel 960HD-50 processor , this printer is compact in size and capable of printing a maximum of approx.
5-228 F AX-L1000 Chapter 5: Appendix d) Operations •Outline When this unit is attached to the main unit, the main unit can be used as a PCL printer . This unit has a centronics interface, and can be used as a local printer by connection with a PC. Also, the following options are available with this board.
5-229 F AX-L1000 Chapter 5: Appendix •The Flow of Print Data The main unit’ s printing operations are done totally independently when faxing and printing, but data communications between the PDL board and the ECNT board are all done through the SCNT board.
5-230 F AX-L1000 Chapter 5: Appendix b.Image Signal (1) The image signal (nVDO) is sent from the PDL board to the TWINS board selector IC. (2) The image signal (nVDO) from the fax (SCNT board) and the image signal (nVDO) from the printer (PDL board) are switched by the selector IC.
5-231 F AX-L1000 Chapter 5: Appendix •Menus Operation Flow Figure 5-92 PDL Menu Flo w CONFIG MENU JAMRECO VER Y=OFF CONFIG MENU AUT OCONT=ON CONFIG MENU DENSITY=7 ECONOMY MODE= OFF CONFIG MENU REFIN.
5-232 F AX-L1000 Chapter 5: Appendix e) Components V ideo controller circuit recei ves print data consisting of code or image data from e xternal device (such as host computer) via interface cable. The circuit analyzes and processes the print data including the data specified by the operation panel, and then con verts them to the dot data.
5-233 F AX-L1000 Chapter 5: Appendix EEPROM (IC10) EEPROM is 4-Kbytes, and is used for storing the factory default value and the user set value defined on the operation panel.
5-234 F AX-L1000 Chapter 5: Appendix Figure 5-94 Block Diagram ASIC RESET Resident ROM ROM DIMM ROM DIMM Extension I/O Extension I/O RAM DIMM RAM 4MB <J2> TWINS board AIR Buffer IEEE1284 EEPROM .
5-235 F AX-L1000 Chapter 5: Appendix 3.10.4 Maintenance and service a) T est print The following items can be printed by selecting and executing a TEST MENU: •SHO W P A GE COUNT Displays the total number of printed pages when used as a printer . The total page number is only shown briefly on the display b ut does not print.
5-236 F AX-L1000 Chapter 5: Appendix Use the T est Print to verify the operation panel selections, system conf igurations (memory and options), and print quality .
5-237 F AX-L1000 Chapter 5: Appendix •Cleaning Page When the dirty fixing unit is the cause of image defect, the fixing unit can be cleaned by the user . The toner on the upper pressure roller can be removed by printing the cleaning pattern in figure 5-96 Cleaning P age and re-feeding the pa per (cleaning page).
5-238 F AX-L1000 Chapter 5: Appendix (1) Press the Go b utton to set the printer off-line. The On line indicator should be OFF and P A USED appears in display . (2) Press the Menu button until you see “ TEST MENU ” in the top line. (3) Go to the “ CLEANING P A GE ” item in the TEST MENU.
5-239 F AX-L1000 Chapter 5: Appendix "5F-52 ERROR" (Scanner unit malfunction) <Possible causes> 1.Poor contact in LASER/scanner unit connectors Action: Reconnect the BD board connector J551, LASER driver board connector J501 and scanner motor connector J401.
5-240 F AX-L1000 Chapter 5: Appendix "5F-56 ERROR" (Duplexing unit exhaust fan (FM701) malfunction) <Possible causes> 1.Poor contact in the connectors of the FM701 drive signal line Action: Reconnect the intermediate connectors J718 and J719, then the duplexing unit driver board connector J707.
5-241 F AX-L1000 Chapter 5: Appendix 4.Defectiv e ECNT board Action: Replace the ECNT board 5.Defective SCNT board Action: Replace the SCNT board. 6.Defectiv e TWINS board Action: Replace the TWINS board. 7.Defective PDL board Action: Replace the PDL board.
5-242 F AX-L1000 Chapter 5: Appendix 3.Defecti ve paper feeder dri ver board Action: Replace the paper feeder driver board. 4.Defective ECNT board Action: Replace the ECNT board. 5.Defective SCNT board Action: Replace the SCNT board. 6.Defecti ve TWINS board Action: Replace the TWINS board.
5-243 F AX-L1000 Chapter 5: Appendix "T ONER CARTRIDGE MISSING" message appears when it is installed <Possible causes> 1.Poor contact between the printer contact and the cartridge contact Action: Clean the contacts if dirty . Replace the part(s) if deformed or damaged, or the problem still remains after cleaning.
5-244 F AX-L1000 Chapter 5: Appendix 2.Defecti ve printer co v er Action: Replace the printer cov er sensor . 3.Defective ECNT board Action: Replace the ECNT board. 4.Defective SCNT board Action: Replace the SCNT board. 5.Defecti ve TWINS board Action: Replace the TWINS board.
5-245 F AX-L1000 Chapter 5: Appendix 3.Defective paper size detection board Action: Replace the paper size detection board. 4.Defective ECNT board Action: Replace the ECNT board. 5.Defective SCNT board Action: Replace the SCNT board. 6.Defectiv e TWINS board Action: Replace the TWINS board.
5-246 F AX-L1000 Chapter 5: Appendix 3.Defecti ve paper feeder dri ver board Action: Replace the paper feeder driver board. 4.Defective paper size detection board Action: Replace the paper size detection board. 5.Defective ECNT board. Action: Replace the ECNT board.
5-247 F AX-L1000 Chapter 5: Appendix 2.Damaged top cover sensor lever of the duplexing unit Action: Replace the top cov er . 3.Defective face-up tray paper sensor Action: Replace the sensor . 4.Defective duplexing unit driver board Action: Replace the duplexing unit driver board.
5-248 F AX-L1000 Chapter 5: Appendix 3.Defecti ve re versing paper sensor Action: Replace the sensor . 4.Defective duplexing unit pick-up paper sensor 1 Action: Replace the sensor . 5.Defective duplexing unit driver board Action: Replace the duplexing unit driver board.
5-249 F AX-L1000 Chapter 5: Appendix PDL board(J2) ,/ TWINS board connector(J33) J2 J33 Signal name Description c1 . 26 GND Ground c2 , 25 nBD Horizontal sync signal c3 , 24 nPPRDY Printer power ready.
5-250 F AX-L1000 Chapter 5: Appendix This page intentionally left blank.
.
Printed on paper that contains 60% reused paper . PRINTED IN JAP AN (IMPRIME AU JAPON) 0200A T0.80-0 CANON INC..
デバイスCanon L1000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Canon L1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCanon L1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Canon L1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Canon L1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Canon L1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCanon L1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Canon L1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCanon L1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
