Carrierメーカー90MAの使用説明書/サービス説明書
ページ先へ移動 of 22
90MA/MU Single-Package Marine Cooling Units Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
FIGURE 1 - BA SE UNIT INTERIOR DETAILS (TYPICA L UNIT SHOWN) Step 4 - Rig and Place Unit - NOTE: Install accessories before placing unit. a. Provide space around unit for service, filter access, and overhead clearance as indicated in Figure 2. b. Move and store unit in upright position.
DIMENSION “D” MUST BE EQUAL ALL AROUND FIGURE 3 - HORIZONTA L WHEEL CENTERING FIGURE 4 - CONCENTRIC WHEEL A LIGNMENT Step 6 – Check Fan Shaft and W heel Alignme nt - HORIZONTAL WHEEL CENT ERING - All wheels must be horizontally centered betw een the inside edges of their fan scroll ventures (Figure.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.S.A. 90MA-3SI SUPERCEDES FORM 62-02971-00 09-2009 Pg 10 a. Route regulating valve capilla ry w ith its flare nut to the fitting on refrigerant discharge line (Figure.
TA BLE 3 - RECOMMENDED LINE SIZ ES (INCHES) REMOTE CONDENSERS DISCH LIQ UID DISCH LIQUID DISCH LIQUID DISCH LIQ UID 404 R-407C 1/2 3/8 5/8 3/8 5/8 3/ 8 5/8 3/8 406 R-407C 5/8 3/8 3/4 3/8 3/4 3/ 8 3/4 .
Step 12 - Make Electrical Connections GENERAL - Provide an adequate fused disconnect switch within sight of the unit. Provision for locking sw itch open (OFF) is advisable to prevent power from being turned on when unit is being serviced. POWER WIRING - Conduit opening for all units is on left side of unit near control box.
SERVICE WARNING NEVER reach into unit while fan is running. LOCK OPEN AND TAG unit disconnect before working on fan. Remove fuses and take them with you after noting this on tag . CAUTION 1. Sharp edges of coil fins are exposed. To prevent injury, cover top of evaporator with cardboard or a few layers of heavy tape.
Eva porator Coil - Observe fan compartment Caution note at the beginning of the Service section. Remove dirt and debris from evaporator coil as required by condition.
Charging the System (90MA) - These units are shipped with a full operating charge. If recharging is necessary (complete charge lost), wei gh in amount of refrigerant indicated on unit nameplate and in Table 1.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.S.A. 90MA-3SI SUPERCEDES FORM 62-02971-00 09-2009 Pg 16 compressor equipped units and on the suction line on all other units.
FOR NOTES AND LEGEND, SEE FIGURE 13 FIGURE 12 WIRING SCHE MATIC - 90MA/MU*04/*06 Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
FIGURE 13 COMPONENT ARRA NGEMENT - 90MA/MU*04/*06 Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
FOR NOTES AND LEGEND, SEE FIGURE 15 FIGURE 14 - ELECTRICAL SCHEMATIC - 90MA/MU*08/*12 Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
FIGURE 15 - COMPONENT ARRANGEMENT - 90MA/MU008/012 Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
FIGURE 16 – MOUNTING BASE ASSEMBLY – 90MA/MU*04/*06 Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
Manufacturer reserves the right to discont inue, or change at any time, specifications or designs without notice and without incurring obligations Printed in U.
デバイスCarrier 90MAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Carrier 90MAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCarrier 90MAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Carrier 90MAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Carrier 90MAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Carrier 90MAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCarrier 90MAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Carrier 90MAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCarrier 90MAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。