CarrierメーカーWIRELESS TRANSCEIVER 33CNOAANT1の使用説明書/サービス説明書
ページ先へ移動 of 16
Manufactu rer reser ves the rig ht to dis continue , or chan ge at a ny time, spec ificat ions or des igns without notice an d withou t inc urring obligations.
2 PREINST ALLA TIO N Every installer should perform site evaluation prior to installing the transceivers. In order to perform this evaluation the following minimum equipment must be purchased from Carrier . The two modem starter kit (33CNWI RMOD) is re- quired to begin performing a site eval uation.
3 Table 1 — H ardwar e Specif ication s Serial Comm unications — In order to configure any transceiver , a 9-pin RS-232 cable must be used. This is neces- sary because Pin 4 is used to transmit the configuration data into EEPROM and other pins are use d during the configuration process as well (see T able 2).
4 Table 2 — Stand-Alone Transceiver Pin Out Anten na I ns talla tion — A ntennas must be connected to each transceiver for proper operation. W ithout an antenna, two units will not communicate. The higher the gain of the an- tenna, the longer t he range of the t ransceiver signal .
5 NO TE: Not recommended f or use on sites with secondary buses. Fig. 3 — Wir eless Mu ltiple Bus Ex tensions of Primary Bus NO TE: Not recommended f or use on sites with secondary buses . Fig. 4 — W ireless Workstat ion NO TE: Not recommended for use on s ites with secondar y buses.
6 W ireless links can only be used t o extend a CCN primary bus (bus D). Do not use bri dges when using a wireless link. Utilizing this primary bus wireless connection to acce s s CCN devices through a bri dge will cause communication messages to be generated on the primary bus.
7 k. Repeat as necessary for m ore transceivers . l. Check Report Genera tio n. m. Clic k Clos e. n. Clic k Canc el. o. Select Ex it f rom the file m enu. 6. V i ew the report . a. Open W indows Explor er. b. Once in W indows Explorer , Open the followin g file: C:Program FilesConfiguration Manager RReport.
8 Modifying Set tings — Y ou can run the Quick Configu- ration wizard to modify settings or you can change e ntries manually in the fields in the modification tabs provided. When manually changing entries, you must cl ick apply and/or store for the changes to take effect.
9 Generating Rep ort s — Reports can be generated dur- ing the Quick Configure (if the box was chec ked) or can be generated at any time using menu commands. T w o types of re- ports can be generated. Information in each report can be cleared separat ely .
10 US E R F U NC T I O N S — T o ch ange the passw ord as a user: 1. Select Change Password from the File menu. Change password dialog appears. See Fig. 15. 2. Enter the desired criteria. Enter user nam e and new password. Retype the new pass- word in Confirm Password.
11 Session Holdoff — (Adjustment of these settings is not recommended.) This will only be enabl ed for a host transceiver and is re - quired to manage t he communication from mul tiple remotes. It prevents a host unit from starting a new session until it com- pletes its current session.
12 T est Communications Between Units: 1. Open the Configuration Manager . See Fig. 17. 2. Click the T e rminal Mode tab. 3. In T est String, enter some text.
13 Fig. 18 — RX Configuration Window Fig. 19 — Loopback Test Window.
14 TROUBLESHOO TING (See T able 7) Table 7 — Troubleshooting System Configur ation — Ref er to th e foll owing to check system configuration: • Do th e power a nd link LE Ds blink 3 time s as de.
15 Q: Should I incorporate lightning surge protection for my tran sceive r? A: It is a good idea whene ver your coax ial cable lengths ar e 20 feet or more. Cont act your Carrier represent ative. Q: What is the hi ghest baud rate of the Carrier RS-485 adapter? A: 9600 Baud.
Manufactu rer reser ves the rig ht to dis continue , or chan ge at a ny time, spec ificati ons or des igns without notice an d wit hout inc urring obligations.
デバイスCarrier WIRELESS TRANSCEIVER 33CNOAANT1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Carrier WIRELESS TRANSCEIVER 33CNOAANT1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCarrier WIRELESS TRANSCEIVER 33CNOAANT1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Carrier WIRELESS TRANSCEIVER 33CNOAANT1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Carrier WIRELESS TRANSCEIVER 33CNOAANT1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Carrier WIRELESS TRANSCEIVER 33CNOAANT1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCarrier WIRELESS TRANSCEIVER 33CNOAANT1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Carrier WIRELESS TRANSCEIVER 33CNOAANT1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCarrier WIRELESS TRANSCEIVER 33CNOAANT1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
