CasioメーカーIT-3000の使用説明書/サービス説明書
ページ先へ移動 of 79
Handheld Printer Terminal User’s Guide Series Be sure to read “Safety Precautions” inside this guide before trying to use your Handheld Printer Terminal. After reading this guide, keep it in a safe place for future reference. E PN410385-007 IT-3000_E_Hyo_1_4.
• This Product is equipped with the Brycen B-RAPPORE Stack and My W irefree Network Bluetooth User Interface Application, the use of which is gov erned by a license granted by Brycen Co., Ltd. ® • BLUETOO TH is a registered trademark owned by Bluetooth SIG, Inc.
E-1 W arning Caution Danger Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the first time. Markings and Symbols The following are the meanings of the markings and symbols used in these Safety Precautions.
E-2 Safety Precautions W arning Foreign Objects • Should any foreign matter get into the Handheld Printer T erminal and its options, immediately turn off the po wer and contact your original vendor or an authorized CASIO service provider . Continued use creates the danger of fire and electric shock.
E-3 Operation of Wireless Data Comm unication Function W ar ning Interference with the Operation of Other Equipment (Using Wireless Data Comm unication Function) • Please follow the instructions provided by health care facilities when using your Handheld Printer T erminal in hospitals or other locations where medical equipment is in use.
E-4 Safety Precautions Caution Foreign Objects • T ake care to ensure that metals or comb ustible objects are not inserted into the openings of the Handheld Printer T erminal and its options. Such objects inside of the Handheld Printer T erminal and its options create the danger of fire and electric shock.
E-5 Lithium-ion Battery Pack Danger • Nev er allo w the battery pack to become wet. W ater can create the danger of battery pack heat emission, explosion, and f ire. • Nev er use or lea ve the batter y pack next to open flame, near a sto ve, or an y other area exposed to high heat.
E-6 Safety Precautions W arning • Nev er place the battery pack in a micro wa v e ov en or any other high-v oltage device. Doing so cr eates the danger of battery pack heat emission, explosion, and f ire.
E-7 AC Power Supply W arning • Do not use the Handheld Printer T erminal at a voltage other than the specified v oltage. Also, do not connect the Handheld Pr inter T erminal to a multi-plug power strip. Doing so creates the danger of fire and electric shock.
E-8 A C Adaptor Caution • The housing of the AC adaptor can become w arm during normal use. • T ake normal precautions against electric shock. • At least once a year , unplug the A C adaptor from the wall outlet and clean any dust that builds up between the prongs of the plug.
E-9 Y our Handheld Printer T erminal and its options are precision digital instruments. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation.
E-10 • The contents of this guide are subject to change without notice. • Note that CASIO COMPUTER CO., L TD. shall not be held liable to you or any third parties for any losses or damages arising from the use of this guide.
E-11 GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
E-12 Regulatory Information L ’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) I’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
E-13 Products are for distribution within all member states of the EU. France limited to 2446.5-2483.5 Mhz Indoor use. Belgium limited to 2400-2483.5 Mhz Indoor , 2460-2483.5 Mhz Outdoor use. The information described abov e dates from January 2003 and may be subjected to future changes.
E-14 Contents Safety Precautions ......................................................................................... E-1 Operating Precautions ................................................................................... E-9 Important ....
E-15 General Guide ................................................................................................... E-54 Connecting the AC Adaptor and Connecting to a Computer ............................ E-56 Configuring DIP Switch Settings ......
E-16 Be sure to perform the following steps before trying to use the Handheld Printer T erminal for the first time. 1. When unpacking, make sure that everything is included. Open the box and make sure that all the items shown here are included. 2. Charge the battery pack.
E-17 3. Load the battery pack into the Handheld Printer T erminal. 1 T urn the battery pack co ver lock switch on the side of the Handheld Printer T erminal to the “FREE” position. 2 Open the battery pack cov er . 3 Install the battery pack(DT -9723LIC).
E-18 4. Hold down the power key for about one second to turn on the po wer . Start up the application you want to run. Before Getting Started IT-3000_E_P16_32.
E-19 Options IT -3000 Series Required A C Adaptor f or Bridge Satellite Cradle / Cradle-type Battery Charger Cradle-type Battery Charger HA-B30CHG HA-B61IO Bridge Satellite Cradle Handheld Printer T erminal System Configuration AD-S42120BE IT-3000_E_P16_32.
E-20 Handheld Priter T erminal System Configuration Battery Pac k DT -9723LIC Formed Sheet Paper Holder HA-B93PH Splash Protect Cover HA-B92PCV Screen Protect Co ver HA-B90DCV IT-3000_E_P16_32.
E-21 A C Adaptor AD-S10095AE AD-S10095A U * See page 66. IT-3000_E_P16_32.p65 07.10.16, 15:12 21.
E-22 Cables DT-887AXA Dsub 9-Pin (Female) RS-232C Cross Cable for Bridge Satellite Cradle DT-888RSC RS-422 Modular Cable for connecting Bridge Satellite Cradle DT-380USB USB Cable for connecting Bridg.
E-23 General Guide 25 3 4 5 6 7 8 9 10 1 2 24 11 12 13 14 15 16 17 18 23 19 20 18 21 22 IT -3000M53E/M54E2/M55E/M55U/M56E/M56U * The C-MOS Imager is only installed on the IT -3000M55E/ M55U/M56E/M56U * Magnetic Card Reader is only installed on the IT -3000M54E2/ M55E/M55U IT-3000_E_P16_32.
E-24 General Guide 1 SD Memory Card Slot 2 Program Key (L) 3 Roll Paper Holder 4 Splash Protect Cov er and Paper Cutter 5 Power K ey 6 Indicator 1 (Left Side) Indicator 2 (Right Side) 7 Speaker 8 Brig.
E-25 15 Battery Pack Cover Lock Switch 16 Battery Pack Cover 17 PC Card Slot 18 Hand Strap Hook 19 14-pin Serial Interface Connector 20 Power T erminals 21 Neck Strap Hooks 22 Magnetic Card Reader (IT.
E-26 1 Fn Key 2 Numeric Keys 3 (Cursor Key) 4 (Cursor Key) 5- 6. 7C 8B S 9 ENT This key is used to switch the character input mode or make various settings in combination with other keys, or start up a pre-registered application. These keys are used to input numbers and letters.
E-27 Replacing the Battery Y our Handheld Printer T erminal uses two types of battery: a battery pack and a memory backup battery . A battery pack (DT -9723LIC) is used for the main battery . A backup battery is housed inside the Handheld Printer T erminal.
E-28 Replacing the Battery T o replace the battery pack 1. Make sure that the Handheld Printer T erminal is turned off. If the power is on, press the po wer k ey to turn it of f. 2. T urn the battery pack cov er lock switch on the side of the Handheld Printer T erminal to the “FREE” position.
E-29 Important! • When replacing the battery pack, make sur e y ou do not lea ve the Handheld Printer T erminal without a battery pack for mor e than about 10 minutes. Doing so can cause data in the memory to be deleted. • Never try to use other type of ba ttery than the one that is specif ied for this product.
E-30 A flexible hand strap can be attached to the Handheld Printer T erminal. Hook A Hand Strap Hook B Attach the hand strap follo wing the procedure described below . 1. Attach Hook B of the hand strap to the hand strap hook located on the bottom of the Handheld Printer T erminal.
E-31 A neck strap can be attached to the Handheld Printer T erminal to keep it from being dropped while being carried. The stylus holder provided can also be attached. Attach the neck strap following the procedure described below . Attachment Pr ocedure 1.
E-32 Remov al Pr ocedure 1. Pull back the locking bar of the neck strap mounting hook and then release the hook from each ring as shown in the illustration.
E-33 2. Remove Mounting Hook C. 3. Pass the stylus holder through the strap as sho wn in the illustration. 4. Fold back the strap after passing through Bracket C, and then fasten in the same way it was originally f astened with Bracket A and Bracket B.
E-34 Calibrating T ouch Screen Alignment Whenever you feel that touch screen response is poor or that the operations being executed do not match the location you are tapping on the touch screen, perform the following operations to calibrate the alignment of the touch screen.
E-35 Adjusting Display Contrast Perform the following steps to adjust display contrast to make display colors more vivid and easier to see. • Press the “Fn” key and then press the “2” key or “3” key after confirming that “F” is displayed in the lower right corner of the screen.
E-36 The printer can print on roll paper (80 mm or 58 mm wide) or 80 mm wide formed sheet paper . When printing on for med sheet paper , use the paper holder (HA-B93PH) sold separately . When Using Roll Paper Installing the Roll Paper 1. Check that the power is of f.
E-37 5. Close the roll paper holder , slide the lock knobs on the left and right sides as shown in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear of f the protruding roll paper . • Please note that the positions of the lock knobs on the left and right sides are different.
E-38 Attaching the 58 mm P aper Width Adjuster Attach the 58 mm Paper Width Adjuster inside the roll paper holder when using 58 mm wide roll paper . Refer to the procedure described in “Installing the Roll Paper” for information on opening and closing the roll paper holder .
E-39 When Using Formed Sheet P aper Attaching the Paper Holder Attach the separately sold Paper Holder (HA-B93PH) when printing on formed sheet paper . The Paper Holder is composed of four parts and four scre ws. In addition, a PC card cushion is enclosed to pre vent the PC card from being dislodged by an impact and so forth.
E-40 5. Loosen the two screws shown in the illustration (the screws cannot be removed). 6. Open the cover (PC card slot cover) as shown in the illustration. 7. Loosen and remove the four screws shown in the illustration. Store the removed screws in a safe place so that they do not become lost.
E-41 10. Fasten P art A of the Paper Holder to the Handheld Printer T erminal. Press both ends of Part A to fasten to the Handheld Printer T erminal. 11 . Insert the projections on both sides of Part into the grooves of Part B and fasten to the Handheld Printer T erminal with the four screws for the Paper Holder .
E-42 Loading Formed Sheet Paper Enable the Auto Loading function by selecting Start, Settings, Control Panel and then “Printing Control” of Printer Settings in that order before loading the formed sheet paper . 1. Insert the formed sheet paper all the way into the printer until it stops with the side to be printed facing downward.
E-43 Precautions When Using Printer Printing Accuracy 1. During high-duty printing such as printing horizontal lines or printing while the battery remaining capacity is lo w , the printing speed may slow down to pre vent excess current consumption that may cause unaligned printing f or one dot or more.
E-44 Others 1. The temperature range f or printing with 2-ply paper and label paper is 5 to 35°C. 2. Once the end mark of the paper appears, promptly r eplace with new paper .
E-45 Using the C-MOS Imager (IT -3000M55E/IT -3000M55U/IT -3000M56E/IT -3000M56U only) 1. T urn on the Handheld Printer T erminal, position its C-MOS Imager reader port near the bar code or 2D code, and then press the T r igger K e y (R or L). 2. The Handheld Printer T erminal reads the code by emitting laser and red lights.
E-46 W arning Label • This label is a warning label f or Class 2 laser pr oducts that comply with IEC60825-1+A2:2001 CA UTION • Use of controls or adjustments or perf ormance of pr ocedur es other than those specified her ein may r esult in hazardous radiation exposur e.
E-47 The Magnetic Card Reader comes as standard with IT -3000M55E/M55U/M54E2. Only use cards that are compatible with the ISO standards. The procedure for reading cards is described belo w .
E-48 IR Communication IR communication can be used to transfer data between two Handheld Printer T erminals. When performing IR communication, orient the IR ports of both Handheld Printer T erminals so the y are pointing directly at each other . Data communication is possible within a distance of 0 (in direct contact) to 1 m (max.
E-49 Bluetooth ® Comm unication Bluetooth ® protocol can also be used to transfer data between two Handheld Printer T erminals. The two Handheld Printer T erminals should be no more than five meters apart (as long as there is nothing blocking the path in between).
E-50 Resetting the Handheld Printer T erminal is the same as restarting a computer . Performing a reset causes all unsaved inputs and edits to be lost, but data that is already stored in the memory as well as all settings should be unaf fected.
E-51 Performing a Full Reset (Initialization) Performing a full reset initializes memory . This means that all data stored in the memory (RAM) is deleted and all the settings are returned to their initial factory settings. Perform a full reset whenever any one of the following conditions exists.
E-52 1. T erminal Model: IT -3000M53E, IT -3000M55E, IT -3000M55U, IT -3000M54E2, IT -3000M56E, IT -3000M56U CPU: Marvell ® PXA255 Application Processor (400 MHz max.) Memory: 64MB RAM, 64MB R OM (user def ined: Approx. 30MB) OS: Microsoft ® W indo ws ® CE .
E-53 Character Size: Free double-width characters Generating Method : Black/white in version, mix ed character font printing 8. Card Slot PC Card Slot: PC Card T ype I/T ype II (3.3 V/5.0 V specifications) * W ake on function av ailable SD Memory Card Slot: SD Memory Card 9.
E-54 Back Bottom Right To p F ront The optionally av ailable Bridge Satellite Cradle (HA-B61IO) mak es it possible to transfer system data and file data between the Handheld Printer T erminal and a computer using an RS-232C interface or USB interface .
E-55 1 System Status Indicator Lamp 2 Communication Indicator Lamp 3 Pow er Indicator Lamp 4 T erminal Detect Switches 5 IR Port 6 Power Contacts 7 Pow er Switch 8 AC Adaptor Jack 9 RS-422 Port 10 RS-232C Port 11 USB Port 12 DIP Switches This lamp indicates whether the system is operating normally .
E-56 Using the Bridge Satellite Cradle (HA-B61IO) Connecting the AC Adaptor and Connecting to a Computer Use the AC adaptor a v ailable as an option for the Bridge Satellite Cradle to supply the po wer to it.
E-57 4. T urn on the po wer . This causes the Bridge Satellite Cradle po wer indicator lamp to light red. 5. Place the Handheld Printer T erminal so that the infrared communication unit on the right side is faced f irmly with the infrared communication unit of the Bridge Satellite Cradle.
E-58 Using the Bridge Satellite Cradle (HA-B61IO) Configuring DIP Switch Settings Removing the bottom co ver of the Bridge Satellite Cradle e xposes the DIP switches. Y ou can change the ON/OFF settings of the DIP switches to set the conf iguration. Only set the DIP switches after first switching OFF the po wer.
E-59 Connecting Multiple Bridge Satellite Cradles (HA-B61IO) Connect “C-OUT” of the Bridge Satellite Cradle connected to the host computer to “C-IN” of the next Bridge Satellite Cradle you want to connect. Important! Y ou can use the optional RS-422 modular cables (DT -888RSC) to link up to eight Bridge Satellite Cradles.
E-60 Model no. of ACAdaptor Area/Region Compliance AD-S42120BE All except China Compliant with CE, UL, FCC, and Energy Ef ficienc y Standards. AD-S42120BE-CN China only Compliant with Ener gy Ef ficienc y Standards and CCC. Bridge Satellite Cradle (HA-B61IO) Specifications 1.
E-61 The optionally av ailable Cradle-type Battery Char ger (HA-B30CHG) lets you charge the Handheld Printer T erminal’ s battery simply by placing the Handheld Printer T erminal onto the charger . General Guide To p F ront Bottom Right Back Using the Cradle-type Battery Char g er (HA-B30CHG) IT-3000_E_P54_77.
E-62 Using the Cradle-type Battery Charger (HA-B30CHG) 1 Power Indicator Lamp 2 T erminal Detect Switches 3 P o wer Contacts 4 Power Switch 5 AC Adaptor Jack This lamp indicates the po wer status and the mounting status of the Handheld Printer T erminal.
E-63 Connecting the A C Adaptor f or the Cradle-type Battery Char ger Use the dedicated A C adaptor for the Cradle-type Ba ttery Char ger to connect to a w all outlet. 1. After making sure that the Cradle-type Battery Charger po wer switch is turned of f, plug the AC adaptor into the A C adaptor jack on the back of the charger .
E-64 Cradle-type Battery Charger (HA-B30CHG) Specifications 1. Charging Charging System: Fix ed-voltage (with current limiter) Charge T ime: Approximately 8.0 hours 2. Po wer Supply Power Requirement: A C adaptor (AD-S42120BE*) Power Consumption: 12V DC, approximately 2,100mA Output to Handheld Printer T erminal : 10V DC 1,800mA (max.
E-65 1. T urn of f the power of the Handheld Printer T erminal by pressing the power key . 2. Open the jack cover ( ), and then insert the plug of the AC Adapter into the charging jack ( ). After connecting the po wer cable to the A C adaptor , plug the other end of it into an electrical outlet.
E-66 Specifications 1. Charging Specif ication Charging Method: Constant current/voltage Charge Period: Approx. 8 hours (with the power of f) 2. A C Adaptor Model: AD-S10095A Input: 100V to 240V AC 50/60 Hz 0.
E-67 PC card compatible with the PCMIA(T ype I/II) standard can be installed in the PC Card slot on the Handheld Printer T erminal. Insert a PC card according to the procedure described belo w .
E-68 Using PC Cards 4. Open the cover (PC card slot co v er) as shown in the illustration. 5. Insert a PC card having PC card remov al tape attached. Insert the PC card all the way in with the top of the card facing to wards the top of the Handheld Printer T erminal.
E-69 Removing a PC Car d Press the eject button on the left side of PC card slot with the stylus as shown b y the arrow , and pull out the PC card while holding onto the end of the PC card remov al tape. Inserting a PC Card (When Using the P aper Holder) Check the names of the parts of the Paper Holder before be ginning work.
E-70 Using PC Cards 3. After pushing on both ends of Part A and reattaching to the Handheld Printer T erminal ( ), remov e Part B by removing the scre ws ( ). 4. Insert a PC card to which PC card remov al tape has been attached. Insert the PC card all the way in so that the top of the PC card faces the top of the Handheld Printer T erminal.
E-71 7. While spreading apart both ends of P art A ( ), remov e Part A from the Handheld Printer T erminal by lifting up Part A until the projections reach the upper edges of the groov es of Part B ( ), and then press on Part C and P art D from the left and right sides ( ).
E-72 1 2 SD memory card can be installed in the SD Memory Card slot on the Handheld Printer T erminal. Insert (or remov e) an SD memory card according to the procedure described below . Inserting an SD Memory Card 1. Check that the power is of f. If the po wer is on, alw ays make sure to turn it of f by pressing the power k ey .
E-73 Connect a bar code reader to the RS-232C interface connector (8-Pin) on the Handheld Printer T erminal. Connecting the bar code reader 1. Check that the power is of f. If the po wer is on, always make sure to turn it of f by pressing the power k e y .
E-74 Attaching the Screen Protect Co ver to the Handheld Printer T erminal prev ents the screen from being cracked or damaged when carrying. 1. Remove the tw o screws on the right side of the Handheld Printer T erminal. Store the scre ws in a safe place after they ha ve been remov ed.
E-75 Attaching the Splash Protect Cov er to the Handheld Printer T erminal lets you use it e ven during inclement weather . Attach the Splash Protect Cov er by following the procedure described belo w .
E-76 5. Close the roll paper holder , slide the lock knobs on the left and right sides as shown in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear of f the protruding roll paper . • Please note that the positions of the lock knobs on the left and right sides are different.
E-77 Important! • Make sur e to attach the contact cov er pro vided when remo ving the Battery Pack from the Handheld Printer T erminal and storing. • If the battery pack has been left over unused f or a long period of time, the capacity remained decr eases due to spontaneous discharge or chemical decomposition by the battery pack itself.
デバイスCasio IT-3000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Casio IT-3000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCasio IT-3000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Casio IT-3000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Casio IT-3000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Casio IT-3000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCasio IT-3000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Casio IT-3000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCasio IT-3000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。