CDAメーカーci925の使用説明書/サービス説明書
ページ先へ移動 of 40
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
2 Important This appliance must only be used for the purpose for which it is intended, i.e. domestic use . Any other use could be dangerous and may lead to premature failure of the appliance. The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product.
3 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority dierentiated waste collection centre or to a dealer providing this service.
4 Safety W arnings • If the plug or cord is damaged, do not connect the appliance to the mains power supply . If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. • T o remove the plug from the socket, pull on the body of the plug, not the cable.
5 W arnings T o avoid the risk of fire, electric shocks, injury or damage when using your washer dryer , please take the following precautions: • Please read all the instructions before using the washer dryer .
6 R ecommendations • R esidues of detergent or softener left in the detergent drawer for long periods will dry and stick to the detergent drawer . T o prevent this put the detergent and softener into the detergent drawer just before washing. • It is recommended that the pre-wash programme should only be used for very dirty clothes.
7 Before First Use When your washer dryer has been correctly installed, we recommend that you pre-clean the machine. This is to check that the installation, the connections and the drainage are all correct, and to thoroughly clean the inside of the washer dryer before any wash programmes are run.
8 • Fasten all zips and buttons. • T urn garments, such as knitted fabrics, inside out. • Before placing the clothes in the drum, make sure all the pockets are empty . Any small objects may block the drain pump. • W e recommend loading the washer dryer to its full capacity for best water and energy eciency .
9 Detergents and Additives Y our washer dryer’ s detergent dispenser has three sections as shown in figure 1. Add the required amount of detergent and fabric softener into the specific sections of the detergent dispenser before starting the wash programme.
10 the remainder to the main detergent section. Do not ex ceed the “MAX” level in the fabric softener section and ensure that concentrated fabric softeners are diluted before use for best washing results. R emember that the amount of detergent to be used will always depend on: • The amount of clothes to be washed.
11 Control P anel C B D A E F G H I A Programme Selector B Display C Spin Speed Selection D W ash T emperature E Delay Button F Extra Rinse Button G Intense Button H Dry Button I Start / P ause Button g.
12 S tarting a W ash Programme • T urn the “Programme Selector” knob to the required programme . • Select the required spin speed using the “Speed Speed” button. • Select the wash temperature using the “W ash T emperature” button. • Select any required extra options, as detailed below .
13 W ash temperature selection Each selected programme has its own preset wash temperature, as shown in the programme listing below . If you press the “W ash T emperature” button the currently set temperature will show on the display .
14 • Once the required time delay is shown on the display , the washing machine will set after appro ximately three seconds delay . Extra rinse This function adds up to 3 extra rinse cycles to the programme, which is ideal for large loads and garments belonging to people with sensitive skin.
15 it is necessary to split the load into 2 batches for drying. See the maximum washing and drying capacities for each programme on page 17 . Start / P ause Press the “Start / P ause” button to start the selected wash programme running, the indicator light stays on.
16 Programme Listing The table below shows the extra functions and temperatures available for each wash programme. Extra Rinse W ash T emperature Options Preset Spin Speed Delay Intense Dry Index Prog.
17 Programme Details The table below shows the details of each wash programme. Index Programme Detergent Compart. Max. Spin Load Capacity (kg) Programme Time Type of L aundry A Prewash ** 1 & 2 6 .
18 EN60456 T esting Details Energy label program settings: 1. “Cotton+ 40°C+Intense Max speed” 2. “Cotton+ 60°C+Intense Max speed” The standard 40° and 60° cotton programmes are suitable to clean normally soiled cotton laundry and they are the most ecient programmes in terms of combined energy and water consumption.
19 Index Programme Max Load (kg) T emp. (°C) Energy Consumption (kWh) W ater Consumption (Litre) W ashing Time Spin Drying Performance B Cotton 6 60 0.808 5 7.7 3:00 53% B Cotton 3 60 0 .811 45. 0 3:00 - B Cotton 3 40 0.6 0 2 43.5 2:49 - Choice of Detergent Notes: The delayed start option is not recommended when using liquid detergent.
20 Care and Maintenance Before beginning any care or maintenance you should always disconnect the appliance from the electricity supply , and also turn o the water supply . If a programme has been run recently , wait for the water in the appliance to cool down to prevent risk of scalding.
21 Pump Filter The pump filter system prevents ingress of lint or foreign objects into the drain pump, reducing the risk of damage. The pump filter should be cleaned regularly , every two to three months at least.
22 g. 5 Detergent Drawer Detergents may cause residue build up in the detergent drawer and the drawer housing over time. The drawer should be cleaned regularly to remove these residues. T o remove the drawer: • Pull the drawer out until it stops.
23 Cleaning the W asher Dryer Exterior The exterior of the washer dryer should be cleaned with warm soapy water or a gentle cleaning agent. Do not use abrasive cleaning products or solvents.
24 Practical Information Alcoholic beverages: The stain should first be washed with cold water , then wiped with glycerine and water and be rinsed with water mix ed with vinegar . Shoe Polish: The stain should be slightly scratched without ruining the cloth, rubbed with detergent and rinsed.
25 Blood stain: Soak the item in cold water for 30 minutes. If the stain still does not disappear , soak in a mixture of water and ammonia (3 table-spoons of ammonia in 4 litres of water) for 30 minutes. Cream, ice-cream and milk: Soak the item in cold water and rub the stained area with detergent.
26 Failure Code Probable failure The process to be done Err1 The door is not shut properly . Shut the door properly so that you hear the click then press the “Start / P ause” button. If the error persists, unplug the machine, close the water tap and contact CD A Customer Care.
27 Failure Code Probable failure The process to be done Er14 Drying motor error Unplug the machine, close the water tap and contact CD A Customer Care. EuAr Communication failure between PCB and motor . Unplug the machine, close the water tap and contact CD A Customer Care.
28 T roubleshooting All repairs which must be done on the machine should only be performed by authorised service agents. When a repairs is required for your machine or you are unable to eliminate the failure with the help of the information given below: • Unplug the machine.
29 Fault Probable cause Methods of elimination The machine does not drain water . The drain hose is obstructed or bent. Check the drain hose. The pump filter is obstructed. Clean the pump filter . The drain hose is above 100cm. Install drain hose at specified height of 80-100cm.
30 Installation T ransit bolts, located at the rear of the appliance, must be removed prior to using the appliance to prevent damage. • R emove the back cover from the machine. • L oosen the transit bolts (T1, T2, T3 & T4 in fig. 6) using a suitable spanner by turning them anti-clockwise and then remove them.
31 installed on a flat, non-slippery and solid surface. The machine must be positioned on a solid support, such as the bare floor or a well-fitting riser , ensuring the machine is unable to fall when subjected to the typical vibrations generated by a washing machine.
32 Fitting the Furniture Door The machine is supplied with a fitting template that aligns with the top of the fascia door and has arrows cut out of it that point toward the door top. NO TE: If this template is aligned with the top of the décor door , the resultant position will align the décor door top with the top of the machine fascia.
33 Connecting to the Mains W ater Supply • Fit the seal included in the hose packing at the end of the water inlet hose on the tap side. • Connect the water inlet hose to a 3/4” BSP water tap.
34 The drain hose must be securely fastened to the outlet to prevent any risk of the drain hose becoming detached and causing ooding. Once the appliance is connected to the water supply and the dra.
35 How to connect an alternative plug If the fitted plug is not suitable for your socket outlet, then it should be cut o and disposed of safely to prevent the risk of electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used.
36 International W ashing Symbols W ash up to 90 °C W ash up to 60 °C Wash up to 30 °C Do not wash in a washing machine W ashing temparatur e Do not wash in a washing machine Lukewarm iron Medium hot iron Hot iron Do not iron Do not tumble dry Hang to dry Drip dry Dry flat Do not bleach Handy to bleach All of these are dry cleaning symbols.
37 NO TES.
38 NO TES.
39 NO TES E & O E. All instructions, dimensions and illustrations are provided for guidance only . CD A reserve the right to change specifications without prior notice.
Please contact our Customer Care Department for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.
デバイスCDA ci925の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
CDA ci925をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCDA ci925の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CDA ci925の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CDA ci925で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CDA ci925を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCDA ci925の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CDA ci925に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCDA ci925デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
