ChauvetメーカーProjector Accessoriesの使用説明書/サービス説明書
ページ先へ移動 of 17
User Manual.
CHAUVET®, 2010, All Rights Reserved Information and specificat ions in this User Manual are subject t o change without not ice. CHAUVET® assumes no responsibility or liabil ity f or any errors or inaccuracies t hat may appear in this manual. A uthor: A nthony Chiappone Revision: 01 Release Date: 01 - 12 - 2011 T ABLE OF C ONTENTS 1.
1. Before You Begin 3 1/13/2011 5:38 PM 1. B EFORE Y OU B EGIN What is i ncl uded • 1 x 6SPOT ™ • 1 x Mounting kit • 1 x Power Cord • 1 x W arrant y Card • 1 x User Manual Unpacki ng Instr.
1. Before You Begin 4 1/13/2011 5:38 PM Safety Instructions • Please keep this User Manual for future consult ation. If you sell the unit to another user, be sure that they also receive this inst ructi on bookl et.
2. Introduction 5 1/13/2011 5:38 PM 2. I NTRODUC TION Product Overview Power In Control P anel (LED Display) DM X Out D M X In Microph one Adjustm ent Power Out Microph one Fuseholder Tripod Stand Fas.
3. Setup 6 1/13/2011 5:38 PM 3. S ETUP AC P o w er This fixture is aut o - ranging and runs on 1 00~240 VAC , 50/ 60 Hz power . To determine the power requirements for a particular fixture, s ee the label affixed to the back plate of the fixture or refer to the fixture’s spec ific at i ons chart.
3. Setup 7 1/13/2011 5:38 PM Mounting Orientation The 6SP OT ™ may be mounted in any position , provided there is adequate room for ventilation. Rigging This fixture has multiple ri ggi ng options.
4. Operating Instruct i ons 8 1/13 /2011 5:38 PM 4. O PERATI NG I NSTRUC TIONS Using the Cont r ol Panel Access control panel functi ons using the four butt ons lo cated directly underneath the LED display.
4. Operating Instruct i ons 9 1/13 /2011 5:38 PM Opera tion DMX Operation This operating mode will allow for control with an external DMX controller. Y ou m ust set the starting address for t his mode. If this is your first time using DMX, then it is recommended that you refer to the “DMX Primer” section in the “Appendix” of this manual.
4. Operating Instruct i ons 10 1/13 /2011 5: 38 PM Master/Slave Mode (Sound - Ac t i v e ) This mode allows a single unit, the master, to operate in either aut omatic or sound - acti ve mode. When additional (slave) f i xtures are daisy chained to the master, t hey will all s ynchronize with the master and run the same lighting show.
5. Appendix 11 1/13/2011 5: 38 PM 5. A PPENDI X Gener al Tr oubleshooti ng S YMPTOM P OSSIBLE C AUSE ( S ) P OSSIBLE A CTION ( S ) Breaker/F use keeps blowing • Ex ce ssi v e cir cuit load • Check.
5. Appendix 12 1/13/2011 5: 38 PM DM X Prim er There are 512 channels in a DMX connection . A fixture capabl e of receiving D MX w ill require one or a number of sequential channels. The user must assign a starting address on the fixture that indicat es the first channel reserved in the controll er.
5. Appendix 13 1/13/2011 5: 38 PM Cable Conne c t or s Cabling must have a male XLR connector on one end and a female X LR connector on the other end . Do not allow contact between the common and the f ixture’s chassis gro und. Ground ing the common can cause a ground loop, and your fixture may perform erratically.
5. Appendix 14 1/13/2011 5: 38 PM 3-Pin to 5-Pin Con version Chart I f you use a controller with a 5 - pin DM X output c onnector, y ou will ne ed to use a 5 - pin to 3- pin adapter.
5. Appendix 15 1/13/2011 5: 38 PM General Maintenance To maintain optimum perform ance and minimize wear, fixtures should be cleaned frequent ly. Usage and environment are contributing f act ors in determi ning cl eaning frequency. As a general rule, fixtures should be cleaned at least t wice a month.
T ECHNI CAL S PECIFICATIO NS WEIGHT & DIME NSI ONS Length ........................................................................................................ 35.5 in (902 mm) W idt h ...........................................................
C ONTACT U S W ORL D HE A DQUARTERS General Inform ation ............................................................................................ CHAUVE T® Address ..................................................................................
デバイスChauvet Projector Accessoriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chauvet Projector Accessoriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChauvet Projector Accessoriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chauvet Projector Accessoriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chauvet Projector Accessoriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chauvet Projector Accessoriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChauvet Projector Accessoriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chauvet Projector Accessoriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChauvet Projector Accessoriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。