Chevroletメーカー2005の使用説明書/サービス説明書
ページ先へ移動 of 416
Seats and Restraint Systems ........................... 1 - 1 Front Seats ............................................... 1 - 3 Rear Seats ............................................... 1 - 8 Safety Belts .............................................
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, and the name COLORADO are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Safety Warnings and Symbols There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning. { CAUTION: These mean there is something that could hurt you or other people.
Vehicle Damage Warnings Also, in this manual you will find these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
These are some examples of symbols that may be found on the vehicle: v.
✍ NOTES vi.
Front Seats ..................................................... .1-3 Manual Seats ............................................... .1-3 Power Seats ................................................. .1-4 Manual Lumbar .................................
Airbag System .............................................. .1-61 Where Are the Airbags? ............................... .1-64 When Should an Airbag Inflate? .................... .1-67 What Makes an Airbag Inflate? ...................... .1-68 How Does an Airbag Restrain? .
Front Seats Manual Seats This section tells you about the seats – how to adjust them, and fold them up and down. { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Power Seats If your vehicle has this feature, there will be a control on the outboard side of the front seat(s). Horizontal Control: Raise or lower the front of the seat by raising or lowering the forward edge of the control. Raise or lower the rear of the seat by raising or lowering the rear edge of the control.
Manual Lumbar If your vehicle has this feature, there will be a knob located on the outboard side of the driver’s seat. Turn the knob counterclockwise to increase lumbar support and clockwise to decrease lumbar support. Heated Seats If your vehicle has this feature, the controls are located on the outboard side of the front seats.
Reclining Seatbacks Your vehicle may have reclining seatbacks. To manually recline your seatback, lift the lever on the outboard side of the seat. Release the lever to lock the seatback where you want it. Pull up on the lever and without pushing on the seatback, the seat will go to an upright position.
{ CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body.
Seatback Latches Your vehicle may be equipped with front seatbacks that fold forward to let people get into the rear seat or to access the storage area behind the seat. To fold the front seatback forward, push the lever on the side of the seat rearward and pull the seatback forward.
2. Grasp the loop located on the side of the seatback you want to fold and pull until you hear a click. 3. Fold the seatback down. 4. Repeat Steps 2 and 3 to fold down the other seatback. { CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash.
Rear Seat Operation (Extended Cab) If your vehicle has an extended cab, there may be a forward folding seat in the rear area. To fold the rear seat down, pull down on the bottom of the seat until the seat is in place. The rear seat storage compartments must be in the rearward position before folding the seat down.
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. { CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly.
A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without belts they could have been badly hurt or killed.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-13.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 1-14.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after an accident if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
3. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What is wrong with this? A: The belt is buckled in the wrong place. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it.
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. Shoulder Belt Height Adjustment Before you begin to drive, move the shoulder belt height adjuster to the height that is right for you.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
When you sit in the center front seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt. To make the belt shorter, pull its free end as shown until the belt is snug.
Rear Seat Passengers It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who are not safety belted can be thrown out of the vehicle in a crash.
2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. If the belt is not long enough, see Safety Belt Extender on page 1-31 .
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Rear Safety Belt Comfort Guides for Children and Small Adults Your vehicle may have rear safety belt comfort guides for the rear outside positions. Rear safety belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults.
2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.
4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-26 . Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. If you have a choice, a child should sit in a seat that has a lap-shoulder belt to get the additional restraint a shoulder belt can provide.
{ CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. Q: What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? A: If the child is sitting in a rear outside seat position, move the child toward the center of the vehicle.
{ CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen.
{ CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12-lb (5.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
{ CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a five-point harness. A booster seat can also help a child to see out the window.
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both.
CAUTION: (Continued) Even though the airbag off switch is designed to turn off the right front passenger’s frontal airbag, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off.
Top Strap Some child restraints have a top strap, or “top tether”. It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
When using a top strap-equipped child restraint in a rear outboard seating position of a crew cab model, route the top strap over the top of the seatback. Then, attach it to the anchor point for that seating position. { CAUTION: Each top tether bracket is designed to anchor only one child restraint.
Crew Cab A. Top Strap Anchorage B. Seatback Latch There are top strap anchors on the back wall behind each rear seating position. You must pull the seatback forward to access the top strap anchors (A). See Rear Seat Operation (Crew Cab) in the Index. 1.
Extended Cab with Rear Seats A. Top strap routing loops B. Top strap anchors C. LATCH anchors (See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-46 . There are two top strap anchorages on the center of the back wall located behind a removable cover for the rear seating positions.
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle is equipped with the LATCH System. For crew cabs, there are anchors for each outboard seating position. You will find the anchors where the seatback meets the back of the seat cushion.
A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. { CAUTION: If a LATCH-type child restraint is not attached to its anchorage points, the restraint will not be able to protect the child correctly.
Securing a Child Restraint Designed for the LATCH System (Crew Cab) 1. Find the LATCH anchorages for the seating position you want to use. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-46 . 2. Put the child restraint on the seat.
3. Attach the LATCH attachments on the child restraint to the LATCH anchorages in the vehicle. The child restraint instructions will show you how. 4. If the child restraint is forward-facing and it has a top tether, install the top tether according to the instructions in Top Strap Anchor Location on page 1-43 and also refer to your child restraint instructions to learn about the proper use of your top tether.
Unless the right front passenger’s frontal airbag has been turned off, never put a rear-facing child restraint in this vehicle. Here is why: { CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s frontal airbag inflates.
2. Find the LATCH anchorages in the passenger seat. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-46 . 3. Put the child restraint on the seat. 4. Attach the LATCH attachments on the child restraint to the LATCH anchorages in the vehicle.
Securing a Child Restraint in a Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-46 . See Top Strap on page 1-42 if the child restraint has one. If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position.
4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock (crew cab only). 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Securing a Child Restraint in the Center Front Seat Position Do not use child restraints in this position. The restraints will not work properly. Securing a Child Restraint in the Right Front Seat Position (Models without an Airbag Of f Switch) Crew Cab Models and Extended Cab Models with Rear Seats If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-46 .
If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Securing a Child Restraint in the Right Front Seat Position (Models with an Airbag Of f Switch) Regular Cab Models and Extended Cab Models without Rear Seats Your vehicle has a right front passenger’s frontal airbag. Regular cab models and extended cab models without rear seats have a switch on the instrument panel that you can use to turn off the right front passenger’s frontal airbag.
Unless the right front passenger’s frontal airbag has been turned off, never put a rear facing child restraint in the right front passenger’s seat. Here is why: { CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s frontal airbag inflates.
If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-46 . See Top Strap on page 1-42 if the child restraint has one. If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
If you were using a rear-facing child restraint, turn on the right front passenger’s frontal airbag when you remove the rear-facing child restraint from the vehicle unless the person who will be sitting there is a member of a passenger airbag risk group.
Here are the most important things to know about the airbag system: { CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
{ CAUTION: Both frontal and side impact airbags inflate with great force, faster than the blink of an eye. If you are too close to an inflating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag inflation before and during a crash.
There is an airbag readiness light on the instrument panel which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-25 for more information.
The right front passenger’s airbag is in the instrument panel on the passenger’s side. If your vehicle has a roof-mounted side impact airbag for the driver and the person seated directly behind the driver, it is located in the ceiling above the side windows.
If your vehicle has a roof-mounted side impact airbag for the right front passenger and the person seated directly behind that passenger, it is located in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? The driver’s and right front passenger’s frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact exceeds a predetermined deployment threshold.
If your vehicle has side impact airbags, it has electronic side sensors. The side impact airbags are designed to inflate in moderate to severe side crashes. A side impact airbag will inflate if the crash severity is above the system’s designed “threshold level”.
Side impact airbags would not help you in many types of collisions, including frontal or near frontal collisions, rollovers, and rear impacts, primarily because an occupant’s motion is not toward those airbags. Airbags should never be regarded as anything more than a supplement to safety belts, and then only in moderate to severe frontal or near-frontal collisions for the driver’s and right front passenger’s frontal airbags, and only in moderate to severe side collisions for side impact airbags.
Your vehicle may have a feature that will automatically unlock the doors, turn the interior lamps on and flash the hazard warning flashers when the airbag inflates (if battery power is available). You can lock the doors again by using the door lock.
Airbag Of f Switch Regular Cab Models and Extended Cab Models without Rear Seats If your vehicle is a regular cab model or an extended cab model without rear seats, it has a switch on the instrument panel that you can use to turn off the right front passenger’s frontal airbag.
Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: • my vehicle has no rear seat; • although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of my vehicle; or • the child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition.
To turn off the right front passenger’s frontal airbag, insert your ignition key into the switch, push in, and move the switch to the off position. The airbag off light will come on to let you know that the right front passenger’s frontal airbag is off.
To turn on the right front passenger’s frontal airbag, insert your ignition key into the switch, push in, and move the switch to the on position. Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to the front of the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, front end sheet metal or height, they may keep the airbag system from working properly.
Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Keys .............................................................. .2-2 Remote Keyless Entry System ........................ .2-3 Remote Keyless Entry System Operation .......... .2-4 Doors and Locks ............................................ .2-7 Door Locks .
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
There is one double-sided key for the ignition, driver’s door lock, and tailgate. When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a key code number. The key code number tells your dealer or a qualified locksmith how to make extra keys.
Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment. At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: • Check the distance.
LOCK: Press this button to lock all the doors. The parking lamps may also flash and the horn may chirp when this button is pressed. Press the button again within three seconds and the horn may chirp. If a door is open or ajar when the lock button is pressed, the horn will chirp several times to let you know that the doors did not lock and the content theft-deterrent system is not armed.
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about two years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Power Door Locks If your vehicle has power door locks, the switches are located on the driver’s and the front passenger’s armrests. Remove the ignition key and press L (lock) to lock all the doors at once. To unlock all the doors, press U (unlock).
Rear Door Security Locks (Crew Cab) If you have the crew cab model, your vehicle may be equipped with rear door security locks. With this feature, you can lock the rear doors so they cannot be opened from the inside by passengers. The security lock lever is located on the inside edge of each rear door.
Lockout Protection If you have power door locks, this feature protects you from locking your key in the vehicle when the key is in the ignition and a door is open. If the power door lock switch is pressed when a door is open and the key is in the ignition, all of the doors will lock and then the driver’s door will unlock.
Removing the Tailgate Follow these steps if you want to remove the tailgate: 1. Lift up slightly on the entire tailgate assembly. Remove the retaining cables from both ends of the tailgate by pulling upward on the clip. Then, push forward so the larger part of the hole on the bracket is over the bolt.
Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows The power window controls are located on the armrest of each door. The driver’s door has switches for the passenger windows as well. Your power windows will work when the ignition has been turned to ACC (Accessory) or ON or when Retained Accessory Power (RAP) is active.
Sliding Rear Window If your vehicle has this feature, squeeze the latch in the center of the window and slide the glass to open it. When you close the window, be sure the latch is engaged. Sun Visors To block glare, pull the visor down. It can also be detached from the center mount and moved to the side to block glare from that direction.
If the lock button on the remote keyless entry transmitter is pressed, but a door is open, the horn will chirp six times. Close the open door and the system will be activated. If a locked door is not opened using the remote keyless entry transmitter, or by OnStar ® , the alarm will go off.
Passlock ® Your vehicle is equipped with the Passlock ® theft-deterrent system. Passlock ® is a passive theft-deterrent system. Passlock ® enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder is tampered with, the fuel system is disabled and the vehicle will not start.
Ignition Positions With the key in the ignition switch, you can turn to four different positions. LOCK (A): This position locks your ignition and transmission on manual transmission vehicles. It is a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to LOCK.
Retained Accessory Power (RAP) Your vehicle is equipped with Retained Accessory Power (RAP) which will allow certain features of your vehicle to continue working for up to 20 minutes after the ignition key is turned to LOCK. Your radio and power windows will work when the ignition key is in ON or ACC.
Depending on the outside temperature, the engine starter may continue cranking the engine up to approximately four seconds after you release the ignition key. This is normal. When starting your engine in very cold weather (below 0°F or 18°C), do this: 1.
To Use the Engine Coolant Heater 1. Turn of f the engine. 2. Open the hood and unwrap the electrical cord. The cord is located in the engine compartment behind the underhood fuse block on the driver’s side of the vehicle. 3. Plug it into a normal, grounded 110-volt AC outlet.
If you need to leave your key in the ignition but not in LOCK for an extended period, it is recommended that you disconnect the battery cable from the battery to prevent discharging your battery. There are several different positions for your shift lever.
NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. { CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, your vehicle could move very rapidly.
SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. You can also use SECOND (2) for starting your vehicle from a stop on slippery road surfaces.
SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD, FOURTH AND FIFTH (3, 4 and 5): Shift into THIRD (3), FOURTH (4) and FIFTH (5) the same way you do for SECOND (2).
If your vehicle has four-wheel drive and is equipped with a manual transmission, disregard the shift light when the transfer case is in four-wheel low. For more information, see Up-Shift Light (Manual Transmission) on page 3-28 . Shift Speeds { CAUTION: If you skip a gear when you downshift, you could lose control of your vehicle.
N (Neutral): Shift the vehicle’s transfer case to NEUTRAL only when towing your vehicle. { CAUTION: Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured.
equipped with a manual transmission. The preferred method for shifting into four-wheel low is to have your vehicle moving 1.2 mph (2 km/h). Press and release the four-wheel low button. You must wait for the four-wheel low indicator light to stop flashing and remain illuminated before shifting your transmission into gear or releasing the clutch pedal.
Shifting to NEUTRAL Use NEUTRAL when you plan to tow your vehicle. See Recreational Vehicle Towing on page 4-50 for towing instructions. To shift the transfer case into NEUTRAL do the following: 1. Set the parking brake. 2. Start the vehicle. 3. Shift the transmission in NEUTRAL (N), or press in the clutch for vehicles with a manual transmission.
Parking Brake The parking brake pedal is located to the left of the regular brake pedal, near the driver’s door. To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot.
Shifting Into Park (P) (Automatic Transmission) { CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Leaving Your Vehicle With the Engine Running { CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
Shifting Out of Park (P) (Automatic Transmission) Your vehicle has an automatic transmission shift lock control system which locks the shift lever in PARK (P) when the ignition is in the LOCK position. In addition, you have to fully apply the regular brakes before you can shift from PARK (P) when the ignition is in ON.
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Running Your Engine While You Are Parked (Automatic Transmission) It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) (Automatic Transmission) on page 2-30 . If you are pulling a trailer, see Towing a Trailer on page 4-56 . Mirrors Manual Rearview Mirror While sitting in a comfortable driving position, adjust the outside rearview mirror so you can see clearly behind your vehicle.
Automatic Dimming Rearview Mirror with Compass and Temperature Display The vehicle may have an automatic dimming rearview mirror with a compass, temperature display, and map lamps. Mirror Operation The mirror automatically changes to reduce glare from headlamps behind you.
Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, your compass could give false readings. The mirror is set in zone eight upon leaving the factory.
Temperature Display Operation The outside air temperature is displayed in the window located at the lower center of the mirror face. Press and hold the far right button for four seconds and release. This will change the temperature reading between degrees Fahrenheit, degrees Celsius, or turn the display off.
The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure to return both mirrors to the unfolded position before driving.
OnStar ® Services For new vehicles equipped with OnStar ® , the Safe and Sound Plan is included for the first year. You can extend this plan beyond the first year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar ® button to speak with an advisor.
Storage Areas Glove Box To open the glove box, pull on the lever. Cupholder(s) Your vehicle may have two cupholders located on the lower part of the front doors as well as two cupholders located at the front end of the console. Vehicles with bench seats may have cupholders attached to the front of the center seat.
Assist Handles Your vehicle may have assist handles to be used when getting out of your vehicle. If your vehicle has assist handles, they may be located above the front passenger door if you have a regular cab, or above the front and rear passenger doors if you have an extended cab or crew cab.
To open a storage box, unhook the bottom of the latches and lift the two latches on each side of the storage box. Lift the lid to access the storage box.
✍ NOTES 2-44.
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 Other Warning Devices .................................. .3-6 Horn ............................................................ .
Audio System(s) ............................................ .3-43 Setting the Time for Radios without Radio Data Systems (RDS) ................................. .3-43 Setting the Time for Radios with Radio Data Systems (RDS) .........................
✍ NOTES 3-3.
Instrument Panel Overview Manual Transmission shown, Automatic Transmission similar 3-4.
The main components of your vehicle’s instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-21 . B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7 . C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-23 .
Hazard Warning Flashers Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located on the instrument panel, between the two air vents in the center.
Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. If you have the tilt steering wheel, you can raise it to the highest level to allow more room for the driver to enter and exit the vehicle. The tilt lever is located on the left side of the steering column, under the turn signal lever.
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.
Headlamp High/Low-Beam Changer 53 (Headlamp High/Low Beam Changer): To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on.
Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. 8 (Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer.
Cruise Control Your vehicle may be equipped with cruise control. 9 (Off): This position turns the system off. R (On): This position activates the system. + (Resume/Accelerate): Move the lever to this symbol to make the vehicle accelerate or resume to a previously set speed.
Setting Cruise Control { CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You’ll now cruise at the higher speed.
Exterior Lamps The control on the driver’s side of your instrument panel operates the exterior lamps. O (Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions. 9 (Off): Turn the knob to this position to turn of f all exterior lamps including the DRLs.
Headlamps on Reminder If a door is open, a reminder chime will sound when your headlamps or parking lamps are manually turned on and your key is out of the ignition. To turn off the chime, turn the headlamp switch to off and then back on. In the automatic mode, the headlamps turn off once the ignition is in LOCK.
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor sees a change in lighting lasting longer than the delay.
Exterior Cargo Lamps You can use the cargo lamps if you need more light in the cargo area of your vehicle or in the top-box storage units. Press this button, located on the driver side of the instrument panel near the exterior lamp control to turn the cargo lamps on and off.
Exit Lighting With exit lighting, the interior lamps will come on when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in. Battery Run-Down Protection This feature shuts off the dome lamp if it is left on for more than 20 minutes when the ignition is in LOCK.
Ashtrays and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. Your ashtray is located at the front of your center console area. The ashtray can be removed for cleaning. When the ashtray is removed, this area can also be used as a cupholder.
Fan Knob 9 (Fan): The center knob on the control panel is used to control the fan speed. Turn the knob clockwise or counterclockwise to increase or decrease the fan speed. If the knob is set on “0” (zero), some outside air will still enter the vehicle and will be directed according to the position of the mode knob.
The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine.
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada).
Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module.
Airbag Of f Light Regular Cab Models and Extended Cab Models without Rear Seats When you turn the airbag off switch to the of f position, the off indictor will come on and stay on to remind you that the airbag has been turned off. When you turn the airbag off switch to the on position, the on indicator will come on.
{ CAUTION: If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger’s frontal airbag could inflate even though the switch is off. If this ever happens, do not let anyone whom the national government has identified as a member of a passenger airbag risk group sit in the right front passenger’s position (for example, do not secure a rear-facing child restraint in the right front passenger’s seat) until you have your vehicle serviced.
Up-Shift Light (Manual Transmission) This light appears when you need to shift to the next higher gear on a manual transmission vehicle. Shifting when the indicator light is on will help you get the best fuel economy. See “Up-Shift Light” under Manual Transmission Operation on page 2-23 for more information.
When the ignition is on, the brake system warning light will also come on when you set your parking brake. See Parking Brake on page 2-29 for more information. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the gage pointer is near the top of the gage, the engine is too hot. It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
Notice: If you keep driving your vehicle with this light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty.
If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-8 .
Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down.
Security Light This light will come on briefly when you turn the key to START. The light will stay on until the engine starts. If the ignition is turned on, and the light flashes, the Passlock ® system has entered a tamper mode. If the vehicle fails to start, see Passlock ® on page 2-16 .
Daytime Running Lamps (DRL) Indicator Light This light turns on whenever the Daytime Running Lamps are on. See Daytime Running Lamps (DRL) on page 3-15 for more information. Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have remaining in the fuel tank.
Driver Information Center (DIC) The DIC display is located on the instrument panel cluster. The DIC can display information such as the trip odometer and personalization features. DIC Controls and Displays The Driver Information Center (DIC) comes on when the ignition is on.
In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 5-13 and Scheduled Maintenance on page 6-4 for more information. Automatic Door Locks This feature allows you to program your door locks to a preferred setting.
Remote Keyless Entry Feedback This feature allows you to program your remote keyless entry feedback to a preferred setting. To set your choice for this feature, perform the following steps: 1. With the engine of f, turn the key to LOCK. 2. Press and hold the lock and unlock buttons on the remote keyless entry transmitter at the same time.
Language This feature allows you to choose the language in which the DIC display will show information. To set your choice for this feature, perform the following steps: 1. With the engine of f, turn the key to ON. 2. Press and release the reset stem until the language is shown on the DIC display.
ABS (Anti-Lock Brake System) This message will be displayed if there is a problem with your antilock brake system. Check your antilock brake system as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page 5-36 and Anti-Lock Brake System Warning Light on page 3-29 for more information.
FLUID This message will be displayed if your brake fluid is low. Check the brake fluid as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page 5-36 for more information. Press the reset stem to acknowledge the message and clear it from the DIC display.
PARK BRK (Brake) This message will be displayed when your vehicle’s parking brake is active. See Parking Brake on page 2-29 and Brake System Warning Light on page 3-28 for more information. The message will clear from the display after the parking brake is released.
Audio System(s) Notice: Before adding any sound equipment to your vehicle, like a tape player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer. Also, check federal rules covering mobile radio and telephone units.
AM-FM Radio Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. RCL (Recall): Press this knob to switch the display between the radio station frequency and the time.
Setting Preset Stations Up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press AM FM to select FM1, FM2, or AM. 3. Tune in the desired station.
To adjust both tone controls and both speaker controls to the middle position, first end out of audio mode by pressing another button, causing the radio to perform that function or by waiting five seconds for the display to return to time of day. Then press and hold AUDIO for more than two seconds until you hear a beep.
With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming • Receive announcements concerning local and national emergencies • Display messages from radio stations • Seek to stations with traff ic announcements This system relies upon receiving specific information from these stations and will only work when the information is available.
For XM™ (if equipped), press the DISPL knob while in XM™ mode to retrieve four different categories of information related to the current song or channel: Artist, Song Title, Category or PTY, Channel Number/Channel Name. To change the default on the display, press the DISPL knob until you see the display you want, then hold this knob for two seconds.
Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2.
Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO knob until BAL appears on the display. Turn the knob to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speakers, push and release the AUDIO knob until FADE appears on the display.
If both PTY and TRAF are on, the radio will search for stations with the selected PTY and traff ic announcements. If the radio cannot find the desired program type, NONE will appear on the display and the radio will return to the last station you were listening to.
The last message can be displayed by pressing the INFO button. You can view the last message until a new message is received or a different station is tuned to. When a message is not available from a station, NO INFO will appear on the display. TRAF (Traff ic): If TRAF appears on the display, the tuned station broadcasts traff ic announcements and when a traff ic announcement comes on the tuned radio station you will hear it.
XM™ Radio Messages Radio Display Message Condition Action Required XL (Explicit Language Channels) XL on the radio display, after the channel name, indicates content with explicit language. These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696).
XM™ Radio Messages (cont’d) Radio Display Message Condition Action Required No Info Category Name not available No category information is available at this time on this channel. The system is working properly. No Info No Text/Informational message available No text or informational messages are available at this time on this channel.
Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in, and READING will appear on the display. The CD should begin playing. If you want to insert a CD with the ignition off, first press the EJT button or the DISPL knob.
4 FWD (Forward): Press and hold this pushbutton to advance quickly within a track. Press and hold this pushbutton for less than two seconds to advance at six times the normal playing speed. Press and hold it for more than two seconds to advance at 17 times the normal playing speed.
Using an MP3 CD MP3 Format This MP3 player will accept MP3 files that were recorded on an up to 700 MB CD-R CD. The files can be recorded with the following fixed bit rates: 32 kpbs, 40 kpbs, 56 kpbs, 64 kpbs, 80 kpbs, 96 kpbs, 112 kpbs, 128 kpbs, 160 kpbs, 192 kpbs, 224 kpbs, 256 kpbs, and 320 kpbs or a variable bit rate.
Order of Play Tracks will be played in the following order: • Play will begin from the first track in the first playlist and will continue sequentially through all tracks in each playlist. When the last track of the last playlist has been played, play will continue from the first track of the first playlist.
Playing an MP3 Insert a CD partway into the slot, label side up. The player will pull it in, and READING will appear on the display. The CD should begin playing and the CD symbol will appear on the display. If you want to insert a CD with the ignition off, first press the EJT button or the DISPL knob.
6 RDM (Random): To random the tracks in the current folder or playlist, press and release this pushbutton. FLDR RDM will appear on the display. Once all of the tracks in the current folder or playlist have been played the system will move on to the next folder or playlist and play all of the tracks in random order.
INFO (Information): INFO will appear on the display whenever a current track has ID3 tag information. Press this button to display the artist name and album contained in the tag. INFO will disappear from the display when the information in the ID3 tag has finished.
Radio with Six-Disc CD Playing the Radio PWR (Power): Push this knob to turn the system on and off. o VOLUME p : Turn this knob to increase or to decrease the volume. INFO (Information): Press this knob to switch the display between the radio station frequency and the time.
Finding a Station BAND: Press this button to switch between FM1, FM2, or AM. The display will show the selection. o TUNE p : Turn this knob to select radio stations. © SEEK ¨ : Press either the SEEK or the TYPE arrows to go to the next or to the previous station and stay there.
Setting the Tone (Bass/Treble) AUDIO: Push and release the AUDIO knob until BASS, MID, or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass, midrange, or treble level. If a station is weak or noisy, decrease the treble.
Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming • Receive announcements concerning local and national emergencies • Display messages from radio stations This system relies upon receiving specific information from these stations and will only work when the information is available.
SCAN: Scan the stations within a PTY by performing the following: 1. Press the TYPE button to activate program type select mode. P-TYPE and the last selected PTY will appear on the display. 2. Turn the TYPE knob or press and release the TYPE button to select a PTY.
A new group of words will appear on the display after every press of this button. Once the complete message has been displayed, INFO will disappear from the display until another new message is received. The last message can be displayed by pressing the INFO button.
LOAD: Press this button to load CDs into the CD player. This CD player will hold up to six CDs. To insert one CD, do the following: 1. Turn the ignition on. 2. Press and release the LOAD button. 3. Wait for the indicator light, located to the right of the slot, to turn green.
To eject multiple CDs, do the following: 1. Press and hold the CD eject button for five seconds. You will hear a beep and the indicator light, located to the right of the slot, will begin to flash and EJECT ALL will appear on the display. 2. Once the light stops flashing and turns green, REMOVE CD # will appear on the display.
RDM (Random): With random, you can listen to the tracks in random, rather than sequential, order, on one CD or on all of the CDs. To use random, do one of the following: • To play the tracks on the CD you are listening to in random order, press and release the RDM button.
Using Song List Mode The six-disc CD changer has a feature called song list. This feature is capable of saving 20 track selections. To save tracks into the song list feature, perform the following steps: 1. Turn the CD player on and load it with at least one CD.
To delete the entire song list, perform the following steps: 1. Turn the CD player on. 2. Press the SONG LIST button to turn song list on. S-LIST will appear on the display. 3. Press and hold the SONG LIST button for more than four seconds. One beep will be heard, followed by two beeps after two seconds, and a final beep will be heard after four seconds.
Theft-Deterrent Feature (Non-RDS Radios) THEFTLOCK ® is designed to discourage theft of your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identification Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOC will appear on the display.
Care of Your CD Player The use of CD lens cleaners for CD players is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD mechanism. Fixed Mast Antenna The fixed mast antenna can withstand most car washes without being damaged.
Your Driving, the Road, and Your Vehicle ......... .4-2 Defensive Driving .......................................... .4-2 Drunken Driving ............................................ .4-2 Control of a Vehicle ....................................... .4-5 Braking .
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-11 .
Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more than 300,000 people injured.
It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
{ CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Please do not drink and drive or ride with a driver who has been drinking.
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traff ic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
TCS operates in all transmission shift lever positions. But the system can upshift the transmission only as high as the shift lever position you have chosen, so you should use the lower gears only when necessary. See Automatic Transmission Operation on page 2-20 and/or Manual Transmission Operation on page 2-23 for more information.
Suppose you are steering through a sharp curve. Then you suddenly accelerate. Both control systems — steering and acceleration — have to do their work where the tires meet the road. Adding the sudden acceleration can demand too much of those places.
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traff ic for several seconds.
• Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane.
If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, your vehicle may straighten out. Always be ready for a second skid if it occurs. Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road.
Before You Go Of f-Roading There are some things to do before you go out. For example, be sure to have all necessary maintenance and service work done. Check to make sure all underbody shields (if so equipped) are properly attached. Be sure you read all the information about your four-wheel-drive vehicle in this manual.
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: • Always use established trails, roads and areas that have been specially set aside for public off-road recreational driving; obey all posted regulations.
Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: • you approach things faster and you have less time to scan the terrain for obstacles.
When you drive over obstacles or rough terrain, keep a firm grip on the steering wheel. Ruts, troughs or other surface features can jerk the wheel out of your hands if you are not prepared. When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground.
Approaching a Hill When you approach a hill, you need to decide if it is one of those hills that is just too steep to climb, descend or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top.
Driving Uphill Once you decide you can safely drive up the hill, you need to take some special steps. • Use a low gear and get a firm grip on the steering wheel. • Get a smooth start up the hill and try to maintain your speed. Do not use more power than you need, because you do not want your wheels to start spinning or sliding.
Q: What should I do if my vehicle stalls, or is about to stall, and I cannot make it up the hill? A: If this happens, there are some things you should do, and there are some things you must not do. First, here is what you should do: • Push the brake pedal to stop the vehicle and keep it from rolling backwards.
Q: Suppose, after stalling, I try to back down the hill and decide I just cannot do it. What should I do? A: Set the parking brake, put your transmission in PARK (P) (or the manual transmission in FIRST (1)) and turn off the engine. Leave the vehicle and go get some help.
Q: Are there some things I should not do when driving down a hill? A: Yes! These are important because if you ignore them you could lose control and have a serious accident. • When driving downhill, avoid turns that take you across the incline of the hill.
Driving Across an Incline Sooner or later, an off-road trail will probably go across the incline of a hill. If this happens, you have to decide whether to try to drive across the incline. Here are some things to consider: • A hill that can be driven straight up or down may be too steep to drive across.
Stalling on an Incline If your vehicle stalls when you are crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you will be right in its path.
Driving in Mud, Sand, Snow or Ice When you drive in mud, snow or sand, your wheels will not get good traction. You cannot accelerate as quickly, turning is more diff icult, and you will need longer braking distances. It is best to use a low gear when you are in mud — the deeper the mud, the lower the gear.
If the water is not too deep, drive slowly through it. At faster speeds, water splashes on your ignition system and your vehicle can stall. Stalling can also occur if you get your tailpipe under water. And, as long as your tailpipe is under water, you will never be able to start your engine.
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. • Drive defensively.
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with misaimed headlamps, slow down a little.
The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traff ic signals, pavement markings, the edge of the road, and even people walking. It is wise to keep your wiping equipment in good shape and keep your windshield washer tank filled with washer fluid.
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
City Driving One of the biggest problems with city streets is the amount of traff ic on them. You will want to watch out for what the other drivers are doing and pay attention to traff ic signals. Here are ways to increase your safety in city driving: • Know the best way to get to where you are going.
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traff ic and keep to the right.
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Highway Hypnosis Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. See Off-Road Driving with Your Four-Wheel-Drive Vehicle on page 4-14 for information about driving off-road.
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 5-54 . Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth, and a couple of reflective warning triangles.
What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing (32°F; 0°C) and freezing rain begins to fall.
If You Are Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: • Turn on your hazard flashers.
You can run the engine to keep warm, but be careful. { CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can.
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If you have a four-wheel-drive vehicle, shift into 4HI. If you have traction control, turn the traction control system off.
{ CAUTION: These hooks, when used, are under a lot of force. Always pull the vehicle straight out. Never pull on the hooks at a sideways angle. The hooks could break off and you or others could be injured from the chain or cable snapping back. Notice: Never use recovery hooks to tow the vehicle.
Tire and Loading Information Label A vehicle specific Tire and Loading Information is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will find the label attached below the door latch post. Vehicle’s without a center pillar, extended cab models, will have the Tire and Loading Information label attached to the driver’s side extended cab door, above the door latch post.
4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs).
Item Description Total A Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs ( 6 8k g )x5= 750 lbs (340 kg) C Available Cargo Weight = 250 lbs (113 kg) Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs ( 9 1k g )x5= 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions.
Certification/Tire Label A vehicle specific Certification/Tire label is attached to the bottom section of the center pillar, on the driver’s side of the vehicle. Vehicles without a center pillar, extended cab models, will have the Certification/Tire label attached to the edge of the driver’s side, extended cab door, below the door latch post.
Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way. Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty.
Two-Tiered Loading By positioning four 2” X 6” wooden planks across the width of the pickup box, you can create an upper load platform. The planks must be inserted in the pickup box depressions. The length of the planks must allow for at least a 3/4 inch (2 cm) bearing surface on each end of the plank.
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-6 . If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing” following.
Four-Wheel Drive Vehicles Use the following procedure to tow your vehicle with all four wheels on the ground: 1. Drive the vehicle to be towed into position behind the tow vehicle. 2. Firmly set the parking brake. See Parking Brake on page 2-29 for more information.
6. Release the parking brake only after the vehicle being towed is firmly attached to the tow vehicle. 7. Turn the ignition to LOCK. If the tow vehicle will not be started or driven for six weeks or more, remove the battery cable from the negative terminal (post) of the battery to prevent your battery from draining while towing.
{ CAUTION: Shifting a four-wheel-drive vehicle’s transfer case into NEUTRAL can cause your vehicle to roll even if the transmission is in Park (P) for an automatic transmission, or if your vehicle is in gear, for a manual transmission. You or others could be injured.
4. Follow the dolly manufacturer’s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle. Make sure the wheels are straight before towing. For manual transmission vehicles, make sure the wheels are straight before proceeding to the next steps.
4. Follow the dolly manufacturer’s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle. For manual transmission vehicles, make sure the wheels are straight before proceeding to the next steps.
Towing a Trailer { CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured.
• Don’t tow a trailer at all during the first 500 miles (800 km) your new vehicle is driven. Your engine, axle or other parts could be damaged. • Then, during the first 500 miles (800 km) that you tow a trailer, don’t drive over 50 mph (80 km/h) and don’t make starts at full throttle.
Vehicle* Axle Ratio Maximum Trailer Weight GCWR** 2WD Regular Cab Automatic Transmission, 2.8L Engine 3.73 3,400 lbs (1 542 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 3.5L Engine 3.42 4,000 lbs (1 814 kg) 8,500 lbs (3 856 kg) Automatic Transmission, 3.
Vehicle* Axle Ratio Maximum Trailer Weight GCWR** Manual Transmission, 2.8L Engine 3.73 2,000 lbs (907 kg) 6,000 lbs (2 722 kg) Manual Transmission, 3.5L Engine 3.42 3,200 lbs (1 451 kg) 7,000 lbs (3 175 kg) Manual Transmission, 3.5L Engine 3.73 3,700 lbs (1 678 kg) 7,500 lbs (3 402 kg) Vehicle* Axle Ratio Maximum Trailer Weight GCWR** 2WD Crew Cab Automatic Transmission, 2.
Vehicle* Axle Ratio Maximum Trailer Weight GCWR** 4WD Regular Cab Automatic Transmission, 2.8L Engine 3.73 3,100 lbs (1 406 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 2.8L Engine 4.10 3,100 lbs (1 406 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 3.
Vehicle* Axle Ratio Maximum Trailer Weight GCWR** 4WD Extended Cab Automatic Transmission, 2.8L Engine 3.73 2,900 lbs (1 315 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 2.8L Engine 4.10 2,900 lbs (1 315 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 3.
Vehicle* Axle Ratio Maximum Trailer Weight GCWR** 4WD Crew Cab Automatic Transmission, 2.8L Engine 3.73 2,700 lbs (1 225 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 2.8L Engine 4.10 2,700 lbs (1 225 kg) 7,000 lbs (3 175 kg) Automatic Transmission, 3.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You’ll find these numbers on the Certification label at the rear edge of the driver’s door above the door latch, or see Loading Your Vehicle on page 4-43 .
Your trailer’s brake system can tap into the vehicle’s hydraulic brake system only if: • The trailer parts can withstand 3,000 psi (20 650 kPa) of pressure. • The trailer’s brake system will use less than 0.02 cubic inch (0.3 cc) of fluid from your vehicle’s master cylinder.
Making Turns Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. Your vehicle could be damaged. Avoid making very sharp turns while trailering. When you’re turning with a trailer, make wider turns than normal.
Parking on Hills { CAUTION: You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged. But if you ever have to park your rig on a hill, here’s how to do it: 1.
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks.
Service ........................................................... .5-3 Doing Your Own Service Work ........................ .5-4 Adding Equipment to the Outside of Your Vehicle ..................................................... .5-5 Fuel ........
Uniform Tire Quality Grading ......................... .5-65 Wheel Alignment and Tire Balance ................. .5-66 Wheel Replacement ..................................... .5-66 Tire Chains ................................................. .5-68 If a Tire Goes Flat .
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-11 .
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
California Fuel If your vehicle is certified to meet California Emission Standards (see the underhood emission control label), it is designed to operate on fuels that meet California specifications. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected.
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty.
Filling Your Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
{ CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { CAUTION: Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs.
Hood Release To open the hood, do the following: 1. Pull the handle with this symbol on it. It is located inside the vehicle on the lower left side of the instrument panel. 2. Release the secondary latch on the hood. It is located below the front center of the hood.
Engine Compartment Overview When you open the hood on the 2.8 L engine (3.5 L engine similar), you will see the following: 5-12.
A. Windshield Washer Fluid. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-35 . B. Coolant Recovery Tank. See Engine Coolant on page 5-25 . C. Power Steering Fluid Reservoir (low in engine compartment). See Power Steering Fluid on page 5-34 .
When to Add Engine Oil If the oil is at or below the cross-hatched area (L), then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-103 .
• SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container.
GM Goodwrench ® oil meets all the requirements for your vehicle. If you are in an area of extreme cold, where the temperature falls below − 20°F ( − 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for your engine at extremely low temperatures.
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL message being turned on, reset the system.
Engine Air Cleaner/Filter The engine air cleaner/filter is located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after 50,000 miles (83 000 km).
{ CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flame if the engine backfires. If it is not there and the engine backfires, you could be burned.
How to Check Because this operation can be a little diff icult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick.
• With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in PARK (P). • Let the engine run at idle for three minutes or more. Then, without shutting off the engine, follow these steps: The transmission dipstick handle has this symbol on it.
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See Recommended Fluids and Lubricants on page 6-12 . Add fluid only after checking the transmission fluid while it is hot. A cold check is used only as a reference.
Then, follow these steps: 1. Remove the filler plug. 2. Check that the lubricant level is up to the bottom of the filler plug hole. 3. If the fluid level is good, install the plug and be sure it is fully seated. If the fluid level is low, add more fluid as described in the next steps.
Hydraulic Clutch The hydraulic clutch linkage in your vehicle is self-adjusting. The clutch master cylinder reservoir is filled with hydraulic clutch fluid. The hydraulic clutch fluid reservoir cap has this symbol on it. See Engine Compartment Overview on page 5-12 for reservoir location.
How to Check and Add Fluid The proper fluid should be added if the level does not reach the bottom of the diaphragm when it is in place in the reservoir. See the instructions on the reservoir cap. Engine Coolant The cooling system in your vehicle is filled with DEX-COOL ® engine coolant.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL ® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. { CAUTION: Adding only plain water to your cooling system can be dangerous.
Adding Coolant If you need more coolant, add the proper DEX-COOL ® coolant mixture at the coolant recovery tank. { CAUTION: Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Engine Overheating You will find a coolant temperature gage on your vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 3-30 . Your air conditioning may stop working if your engine is too hot. This is normal and helps cool the engine.
If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traf f ic, let the engine idle in NEUTRAL while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL and let the engine idle. 2.
When the engine is cold, the coolant level should be at least up to the FULL COLD mark. If it is not, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. { CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL ® engine coolant at the coolant recovery tank. See Engine Coolant on page 5-25 for more information.
When the coolant in the coolant recovery tank is at the FULL COLD mark, start your vehicle. If the overheat warning continues, there is one more thing you can try. You can add the proper mixture directly to the radiator, but be sure the cooling system is cool before you do it.
4. Then fill the coolant recovery tank to the FULL COLD mark. 5. Reinstall the cap on the coolant recovery tank, but leave the radiator pressure cap off. 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
Engine Fan Noise This vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the clutch is not engaged. This improves fuel economy and reduces fan noise.
How to Check Power Steering Fluid 1. Turn the key of f and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag. 4. Replace the cap and completely tighten it.
Adding Washer Fluid Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location. Notice: • When using concentrated washer fluid, follow the manufacturer’s instructions for adding water.
So, it is not a good idea to top off your brake fluid. Adding brake fluid will not correct a leak. If you add fluid when your linings are worn, then you will have too much fluid when you get new brake linings. You should add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system.
What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. See Recommended Fluids and Lubricants on page 6-12 . Always clean the brake fluid reservoir cap and the area around the cap before removing it.
{ CAUTION: The brake wear warning sound means that soon your brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you.
4. Open the hoods and locate the positive (+) and negative ( − ) terminal locations on the other vehicle. Your vehicle has a remote positive (+) and a remote negative ( − ) jump starting terminal. See Engine Compartment Overview on page 5-12 for more information on the terminal locations.
6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, located on the rear axle, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole.
Front Axle When to Check and Change Lubricant It is not necessary to regularly check your front axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Bulb Replacement For the proper types of bulbs to use, see Replacement Bulbs on page 5-51 . For any bulb changing procedure not listed in this section, contact your dealer’s service department. Halogen Bulbs { CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
To replace the bulbs, do the following: 1. Open and support the hood. See Hood Release on page 5-11 . 2. Access the bulb/sockets from the engine compartment. 3. Turn the bulb socket counterclockwise and pull it straight out of the headlamp housing. 4.
Front Turn Signal, Sidemarker and Daytime Running Lamps 1. Remove the turn signal/parking lamp/daytime running lamp (DRL) assembly by pressing on the release clip on the outboard side of the housing and pulling the outboard end of the lamp toward you.
Center High-Mounted Stoplamp (CHMSL) 1. Remove the screws and lift of f the lamp assembly. 2. Turn the bulb socket counterclockwise and remove it from the housing. 3. Pull the bulb straight out of the socket. 4. Insert the new bulb into the socket and press it in until tight.
2. Remove the two rear lamp assembly screws near the tailgate latch. 3. Pull out the lamp assembly. 4. Turn the bulb socket counterclockwise to remove it from the taillamp housing. 5. Pull the old bulb straight out from the socket. 6. Press a new bulb into the socket and turn the socket clockwise into the taillamp housing until it is tight.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear and cracking. See “Wiper Blade Check” under Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways.
4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced of f as the insert is fully inserted.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Tire Sidewall Labelling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. (A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description.
(A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) P-Metric Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kiloPascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall.
UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.
A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar), below the driver’s door latch. This label shows your vehicle’s original equipment tires and the correct inflation pressures for your tires when they are cold.
Tire Inspection and Rotation Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-63 and Wheel Replacement on page 5-66 for more information.
{ CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Buying New Tires To find out what kind and size of tires you need, look at the the Tire and Loading Information label. For more information about this label and its location on your vehicle, See Loading Your Vehicle on page 4-43 . The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traff ic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
{ CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Tire Chains { CAUTION: If your vehicle has P225/75R15, P265/75R15, P235/50R17 or P235/50R18 size tires, do not use tire chains. They can damage your vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts.
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
When you have a flat tire, use the following as a guide to assist you in the placement of the wheel blocks. The following information will tell you next how to use the jack and change a tire. Removing the Spare Tire and Tools The tools you will need are located under the passenger’s seat.
For regular and extended cab vehicles, the jack and wheel blocks are located under the cover at the center of the vehicle behind the front seats. The vehicle will have a cover if it is an extended or regular cab. 1. Move the seats forward to access the cover.
A. Jack Handle Extensions B. Bottle Jack C. Extension Tool D. Wheel Wrench E. Wheel Blocks 1. Assemble the wheel wrench (D) and the jack handle extensions (A) as shown. 2. Insert the hoist end (chiseled end) of the extension tool (C) through the hole in the rear bumper and into the funnel-shaped guide.
4. Tilt the retainer when the tire has been lowered, and slide it up the cable so it can be pulled up through the wheel opening. 5. Put the spare tire near the flat tire. Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions to remove the flat tire and raise the vehicle.
1. Remove the center cap by placing the chisel end of the wheel wrench (E) in the slot on the wheel and gently prying the cap out. If your vehicle has the Xtreme package, remove each wheel nut cap with the wheel wrench and remove the center cap by hand.
{ CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
If the flat tire is on the front of the vehicle, position the jack to the rear of the front tire in the pocket off of the frame. If the flat tire is on the rear, position the jack under the rear axle and get as close as possible to the shock absorber.
4. Make sure the jack head is positioned so that the rear axle is resting securely between the grooves that are on the jack head. 5. Turn the wheel wrench clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit under the wheel well.
7. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 8. Place the spare tire on the mounting surface. { CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.
10. Turn the wheel wrench counterclockwise to lower the vehicle. Lower the jack completely. Front Position Rear Position 5-80.
{ CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.
Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare must be installed with the valve stem pointing down.
3. Loosen the cable by turning the wheel wrench counterclockwise three or four turns. 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with Step 5 under Removing the Spare Tire and Tools on page 5-71 . 5. Turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed.
11. Remove the jack handle and insert the hoist end of the extension through the hole in the rear bumper. Turn the wheel counterclockwise one turn or until the wheel retainer assembly falls out. 12. Reinsert the jack handle into the jack. Lower the jack by turning the wheel wrench counterclockwise.
14. Tilt the tire retainer at the end of the cable and pull it through the wheel opening. Pull the tire out from under the vehicle. 15. If the cable is hanging under the vehicle, turn the wheel wrench clockwise to raise the cable back up. Have the hoist assembly inspected as soon as you can.
2. Tilt the retainer downward and through the wheel opening. Make sure the retainer is fully seated across the underside of the wheel. 3. Attach the wheel wrench and extensions together.
4. Insert the hoist end through the hole in the rear bumper and into the funnel-shaped guide. 5. Turn the wheel wrench clockwise to raise the tire part way up. Make sure the retainer is seated in the wheel opening and the valve stem is pointed down. 6.
To store the tools, do the following: 1. Return the wheel wrench, jack extensions and the storage bag to the locations described under Removing the Spare Tire and Tools on page 5-71 . 2. Reinstall the jack and wheel blocks, be sure to install the wheel blocks first.
The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can finish your trip and have your full-size tire repaired or replaced where you want. For heavy payloads or towing, and for low traction or four-wheel-drive conditions, repair or replace the full-size tire, and reinstall for best performance.
Appearance Care Cleaning products can be hazardous. Some are toxic. Other cleaning products can burst into flames if a match is struck near them or if they get on a hot part of the vehicle. Some are dangerous if their fumes are inhaled in a closed space.
Most stains can be removed with club soda water. To clean, use the following instructions: 1. For liquids: blot with a clean, soft, white cloth. For solids: remove as much as possible and then vacuum or brush. 2. Apply club soda water to a clean, soft, white cloth.
Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. This may have to be done more than once. • Things like tar, asphalt, and shoe polish will stain if they are not removed quickly. Use a clean cloth and vinyl cleaner.
Care of Safety Belts Keep belts clean and dry. { CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-93 . Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish.
Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap, or other material may be on the blade or windshield. Clean the outside of the windshield with a glass cleaning liquid or powder and water solution.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Description Usage Polishing Cloth Wax-Treated Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil, and asphalt.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Engine Compartment Fuse Block The engine compartment fuse block is located on the driver’s side of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. To remove the cover, push in on the tab on the end of the cover and lift.
Fuse Usage 12 Passenger’s Side Headlamp 13 Fuel Pump 14 Wiper 15 Front Axle Actuator 16 Antilock Brake System (ABS), ABS module, Four-Wheel Drive, Gravity Sensor 17 Supplemental Inflatable Restrain.
Fuse Usage 41 Climate Control Fan 42 Power Windows (If Equipped) 43 Starter Solenoid Relay 44 Antilock Brake System 2 (ABS Pump) 45 Antilock Brake System 1 (ABS Logic) 46 Power Seat Circuit Breaker/PO.
Capacities and Specifications The following approximate conversion capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Capacities and Specifications Application Capacities English Metric Air Conditioning Refrigerant R134a 1.
Capacities and Specifications (cont’d) Application Capacities English Metric Transmission (Drain and Refill) Automatic Manual 5.0 quarts 2.5 quarts 4.7 L 2.4 L Wheel Nut Torque 100 ft lb 140 Y All capacities are approximate. When adding, be sure to fill to the appropriate level or as recommended in this manual.
Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using Your Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.
This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-43 . • are driven on reasonable road surfaces within legal driving limits.
Owner Checks and Services on page 6-9 tells you what should be checked, when to check it and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Normal Maintenance Replacement Parts on page 6-14 .
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 5-13 . Reset oil life system. See Engine Oil Life System on page 5-16 . An Emission Control Service. •• Visually check for any leaks or damage.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) Inspect fuel system for damage or leaks.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) Engine cooling system service (or every 5 years, whichever occurs first). An Emission Control Service.
(e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench dealer can assist you with these checks and services.
At Least Once a Year Starter Switch Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK in each shift lever position. • With an automatic transmission, the ignition should turn to LOCK only when the shift lever is in PARK (P).
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Chassis Lubrication Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Front and Rear Axle SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 12378261, in Canada 10953455) meeting GM Specification 9986115.
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your GM dealer. Part GM Part Number ACDelco ® Part Number Automatic Transmission Filter Kit 24225323 — Engine Air Cleaner/Filter 15202408 A1624C Engine Oil Filter 2.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-16.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-17.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-18.
Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-3 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments.
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to filing a court action, use of the program is free of charge and your case will generally be heard within 40 days.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Chevrolet by dialing: 1-800-833-CHEV (2438).
Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.
Roadside Assistance Program As the owner of a new Chevrolet vehicle, you are automatically enrolled in the Chevrolet Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road.
While we hope you never have the occasion to use our service, it is added security while traveling for you and your family. Remember, we are only a phone call away. Chevrolet Roadside Assistance: 1-800-CHEV-USA (1-800-234-8872), text telephone (TTY) users, call 1-888-889-2438.
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, Chevrolet helps minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Participating dealers can provide you with shuttle service to get you to your destination with minimal interruption of your daily schedule.
Additional Program Information Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is not part of the New Vehicle Limited Warranty. A separate booklet entitled “Warranty and Owner Assistance Information” furnished with each new vehicle provides detailed warranty coverage information.
To read this information, special equipment is needed and access to the vehicle or the device that stores the data is required. GM will not access information about a crash event or share it with others other than: • with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee, • in response to an off icial request of police or similar government off ice, • as part of GM’s defense of litigation through the discovery process, or • as required by law.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited. You may write to: Transport Canada 330 Sparks Street Tower C Ottawa, Ontario K1A 0N5 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify General Motors.
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
A Accessory Power Outlets ................................. 3-18 Adding Equipment to Y our Airbag-Equipped V ehicle ....................................................... 1-75 Additives, Fuel ................................................. 5 - 6 Add-On Electrical Equipment .
Audio System(s) (cont.) Care of Y our CDs ........................................ 3-73 Chime Level Adjustment ............................... 3-74 Fixed Mast Antenna ..................................... 3-74 Radio with CD ...........................
Center Front Passenger Position, Safety Belts ....... 1-24 Center High-Mounted Stoplamp (CHMSL) ........... 5-50 Chains, T ire ................................................... 5-68 Check Engine Light ............................................... 3-30 Checking Things Under the Hood .
Customer Assistance Information (cont.) Customer Assistance for T ext T elephone (TTY) Users ....................................................... 7 - 4 Customer Assistance Off ices ........................... 7- 4 Customer Satisfaction Procedure ..
Engine Air Cleaner/Filter ......................................... 5-18 Battery ....................................................... 5-40 Check and Service Engine Soon Light ............ 3-30 Coolant ...............................................
G Gage Engine Coolant T emperature ......................... 3-30 Fuel .......................................................... 3-35 Speedometer .............................................. 3-24 T achometer ........................................
J Jump Starting ................................................. 5-41 K Keyless Entry System ....................................... 2 - 3 Keys ............................................................... 2 - 2 L Labelling, T ire Sidewall ........
M Maintenance Schedule Additional Required Services ........................... 6 - 6 At Each Fuel Fill ........................................... 6 - 9 At Least Once a Month .................................. 6 - 9 At Least Once a Y ear ............
Operating Y our All-Wheel-Drive V ehicle Of f Paved Roads .............................................. 4-14 Other W arning Devices ...................................... 3 - 6 Outlet Adjustment ............................................ 3-21 Outside Convex Mirror .
Rear Axle ...................................................... 5-44 Rear Door Security Locks .................................. 2 - 9 Rear Doors .................................................... 2-10 Rear Safety Belt Comfort Guides ..............
Safety Belts (cont.) Rear Seat Passengers ................................. 1-26 Right Front Passenger Position ...................... 1-24 Safety Belt Extender .................................... 1-31 Safety Belt Use During Pregnancy ...............
Storage Areas Cupholder(s) ............................................... 2-41 Front Armrest Storage Area ........................... 2-41 Glove Box .................................................. 2-41 Rear Storage Area ...........................
T ransmission Fluid, Automatic ........................................... 5-19 Fluid, Manual .............................................. 5-22 Up-Shift Light .............................................. 3-28 T ransmission Operation, Automatic ...
Windshield W asher ......................................... 3-10 Fluid .......................................................... 5-35 Windshield Wiper Blade Replacement ...................................... 5-52 Fuses ..............................
デバイスChevrolet 2005の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chevrolet 2005をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChevrolet 2005の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chevrolet 2005の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chevrolet 2005で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chevrolet 2005を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChevrolet 2005の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chevrolet 2005に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChevrolet 2005デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
