Chevroletメーカー2009 Impalaの使用説明書/サービス説明書
ページ先へ移動 of 406
Seats and Restraint System ............................. 1 - 1 Head Restraints ......................................... 1 - 2 Front Seats ............................................... 1 - 4 Rear Seats .............................................. 1-10 Safety Belts .
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, the IMPALA Emblem, and the name IMPALA are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without further notice.
Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant Temperature O : Exterior Lamps # : Fog Lamps .
Head Restraints .............................................. .1-2 Front Seats ..................................................... .1-4 Manual Seats ............................................... .1-4 Power Seats ..................................
Head Restraints The vehicle’s front seats have adjustable head restraints in the outboard seating positions. { CAUTION: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
Front Seats Manual Seats { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Power Seats On vehicles with power seats, the controls used to operate them are located on the outboard side of the seats. To adjust the seat: • Move the seat forward or rearward by sliding the control forward or rearward. • Raise or lower the front part of the seat cushion by moving the front of the control up or down.
Manual Lumbar On vehicles with manual lumbar, the lever is located on the outboard side of the driver seat near the front of the seat cushion. Lift up or push down on the lever repeatedly to increase or decrease lumbar support. Heated Seats On vehicles with this feature, the buttons that control the driver and front passenger heated seats are located on the climate control panel.
Reclining Seatbacks Manual Reclining Seatbacks { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
To return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked. Power Reclining Seatback The driver seat may have a power reclining seatback.
{ CAUTION: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Center Seat The vehicle may have a front center seat. There are cupholders on the underside of the seat cushion. To use them, flip the seat cushion forward. The seat can also be used as a storage area by lowering the seatback. See Center Console Storage on page 2-43 .
To use this feature: 1. Make sure the front seats are not reclined. If they are, the seat cushion will not flip forward completely. 2. Flip the bottom seat cushion forward by pulling up on the tab located in the center of the seat cushion where the seatback meets the seat cushion.
To return the seats to the normal position: { CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. { CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-15.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 1-16.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What is wrong with this? A: The belt is behind the body. { CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder except for the center front passenger position, if your vehicle has one, which has a lap belt. See Lap Belt on page 1-32 for more information. The following instructions explain how to wear a lap-shoulder belt properly.
4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjustment” later in this section for instructions on use and important safety information. 5. To make the lap part tight, pull up on the shoulder belt.
Shoulder Belt Height Adjuster The vehicle has shoulder belt height adjusters for the driver and right front passenger positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
{ CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
To make the belt shorter, pull its free end as shown until the belt is snug. If the belt is not long enough, see Safety Belt Extender on page 1-33 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if necessary.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the way back on the seat.
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
{ CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.
{ CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
{ CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. Securing an Add-On Child Restraint in the Vehicle { CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Wherever a child restraint is installed, be sure to secure the child restraint properly.
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat.
{ CAUTION: Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child restraint per anchor.
2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor.
Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-45 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-43 . In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-45 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-45 for top tether anchor locations.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint” under Passenger Sensing System on page 1-65 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.
Here are the most important things to know about the airbag system: { CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
The right front passenger frontal airbag is in the instrument panel on the passenger side. The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
Roof-rail airbags are not intended to inflate in rollovers or rear impacts. A seat-mounted side impact airbag is intended to deploy on the side of the vehicle that is struck. Both roof-rail airbags will deploy when either side of the vehicle is struck.
What Will You See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy.
In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system.
The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag, seat-mounted side impact airbags, and roof-rail airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat.
The passenger sensing system is designed to turn off the right front passenger frontal airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a child restraint. • A right front passenger takes his/her weight off of the seat for a period of time.
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag: 1.
Additional Factors Af fecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat. If this is not desired, remove the object from the seat. { CAUTION: Stowing of articles under the passenger seat or between the passenger seat cushion and seatback may interfere with the proper operation of the passenger sensing system.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Keys .............................................................. .2-3 Remote Keyless Entry (RKE) System ............... .2-4 Remote Keyless Entry (RKE) System Operation .................................................. .2-5 Remote Vehicle Start ..
Universal Home Remote System ..................... .2-36 Universal Home Remote System Operation (With Three Round LED) ........................... .2-37 Storage Areas ............................................... .2-43 Glove Box ....................
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Remote Keyless Entry (RKE) System If this vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules.
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-4 .
L (Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The turn signal lamps flash and the horn sounds three times. Press and hold L for more than two seconds to activate the panic alarm. The turn signal lamps flash and the horn sounds repeatedly for 30 seconds.
Remote Vehicle Start Your vehicle may have a remote starting feature that allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active and the vehicle has an automatic climate control system, it will automatically regulate the inside temperature.
If it is the first remote start since the vehicle has been driven, repeat the previous steps, while the engine is still running, to extend the engine running time by 10 minutes from the time you repeat the steps for remote starting. The remote start running time can be extended one time and only after the first remote start.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Power Door Locks A power door lock switch is located on both front doors next to the door handle. Press the top of the switch to unlock all doors or press the bottom of the switch to lock all doors. If the vehicle has the optional content theft-deterrent system and it is armed, the power door lock switches will be disabled.
Programmable Automatic Door Unlock The vehicle is programmed so that when the shift lever is moved into P (Park) all doors will unlock. With the vehicle stopped and the engine running, door unlocking can be programmed through prompts displayed on the Driver Information Center (DIC).
To open a rear door when the security lock is on, do the following: 1. Unlock the door using the Remote Keyless Entry (RKE) transmitter, if the vehicle has one, the power door lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside.
Trunk Release To open the trunk from the outside, press the trunk release button on the RKE transmitter, if equipped. Remote Trunk Release G (Remote Trunk Release): Press the button located next to the exterior lamps control on the left side of the instrument panel to open the trunk.
Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window.
Express-Down Window The driver window switch has an express-down feature labeled AUTO. This lets you lower the window completely without holding the switch. Press the front of the switch to the second position and release. To stop the window while it is lowering, briefly pull up on the switch.
Once armed, the alarm will go off if someone tries to enter the vehicle without using the RKE transmitter or a key or turns the ignition on with an incorrect key. The horn will sound and the turn signal lamps will flash for about 30 seconds. When the alarm is armed, the trunk may be opened with the RKE transmitter.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
See your dealer/retailer or a locksmith who can service PASS-Key ® III+ to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new additional key: 1. Verify that the new key has a 1 stamped on it. 2. Insert the original, already programmed, key in the ignition and start the engine.
Ignition Positions The ignition switch has four different positions. To shift out of P (Park), the ignition must be in ON/RUN and the brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key.
Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine turned off: • Audio System • Power Windows • Sunroof The radio will work when the key is in ON/RUN or ACC/ACCESSORY. Once the key is turned from ON/RUN to LOCK/OFF the radio will continue to work 10 minutes or until the driver door is opened.
2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds.
{ CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet.
Automatic Transmission Operation The automatic transmission has a shift lever on the steering column or on the console between the seats. There is a display, located on the instrument panel cluster that will indicate the gear the vehicle is in. Maximum engine speed is limited on automatic transmission vehicles while in P (Park) or N (Neutral) to protect driveline components from improper operation.
R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
3 (Third): This position is also used for normal driving. However, it reduces vehicle speed more than D (Drive) without using the brakes. You might choose 3 (Third) instead of D (Drive) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill.
A warning chime will sound and a brake warning light located on the instrument panel cluster will come on, if the parking brake is set, the ignition is on and the vehicle speed is greater than 5 mph (8 km/h). Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts.
Console Shift Lever If the vehicle is equipped with a console shift lever, use this procedure to shift the vehicle into P (Park): 1. Hold the brake pedal down. 2. Move the shift lever into P (Park) by pushing the lever all the way toward the front of the vehicle and then to the left.
If torque lock does occur, your vehicle may need to be pushed uphill by another vehicle to relieve the parking pawl pressure, so you can shift out of P (Park). Shifting Out of Park Automatic Transmission Shift Lock The vehicle has an electronic shift lock release system.
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Pull the lever, located at the bottom of the mirror for nighttime use.
2. Press one of the four buttons located on the control pad to move the mirror to the desired direction. 3. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen. Keep the selector switch in the center position when not adjusting either outside mirror.
OnStar Turn-by-Turn Navigation service, with one trial route, is available on most vehicles. Press the OnStar button to have an OnStar advisor contact Roadside Service. OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature.
OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days.
This information usually includes the vehicle’s GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). When the Virtual Advisor feature of OnStar Hands-Free Calling is used, the vehicle also sends OnStar the vehicle’s GPS location so they can provide services where it is located.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
4. Immediately, within one second, release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the same button again. The garage door should move, confirming that programming is successful and complete.
The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program the Universal Home Remote.
2. Write down the eight to 12 switch settings from left to right as follows: • When a switch is in the up position, write “Left.” • When a switch is in the down position, write “Right.” • If a switch is set between the up and down position, write “Middle.
5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button that will be used to control the garage door until the garage door moves.
Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders Cupholders may be built into the front center console, front portion of the front center seat, and rear armrest of the vehicle. Sunglasses Storage Compartment A storage compartment for sunglasses may be located above the rearview mirror.
Sunroof On vehicles with a sunroof, the sunroof switches are located on the overhead console. The sunroof can only be operated when the ignition is in ON/RUN, ACC/ACCESSORY, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-21 .
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 H o r n ............................................................ .3-6 Tilt Wheel ...........................................
Oil Pressure Light ........................................ .3-39 Security Light .............................................. .3-39 Fog Lamp Light ........................................... .3-40 Cruise Control Light ...............................
✍ NOTES 3-3.
Instrument Panel Overview 3-4.
The main components of the instrument panel are listed here: A. Outlet Adjustment on page 3-23 . B. Remote Trunk Release Button. See Trunk on page 2-12 . C. Turn Signal/Multifunction Lever on page 3-7 . D. Instrument Panel Cluster on page 3-25 . E. Hazard Warning Flashers on page 3-6 .
Hazard Warning Flashers The hazard warning flashers let you warn others that you have a problem. The hazard warning flasher button is located on top of the steering column. | : Press to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off.
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : Turn and Lane Change Signals 2 : Headlamp High/Low-Beam Changer N : Windshield Wipers L Q : Windshield Washer Flash-to-Pass. For information on the headlamps, see Exterior Lamps on page 3-12 .
Turn Signal On Chime If either one of the turn signals are left on and the vehicle has been driven more than 3/4 mile (1.2 km), a chime will sound. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you.
Windshield Washer At the top of the multifunction lever, there is a paddle with the windshield washer symbol on it. Push the paddle to spray washer fluid on the windshield. The wipers run for several sweeps and then either stop or return to the preset speed.
The cruise control buttons are located on left side of the steering wheel. T (On/Off): Press to turn cruise control on and of f. The indicator is lit when cruise control is on. + RES (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed.
Resuming a Set Speed If cruise control is set at a desired speed and the brakes are applied, this shuts off the cruise control. However, it does not need to be reset. Once your vehicle reaches a speed of about 25 mph (40 km/h) or more, press the +RES button on the steering wheel.
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain your speed. When going downhill, you might have to brake or shift to a lower gear to keep your speed down.
The exterior lamps control has four positions: O (Off): Turns of f the automatic headlamps and daytime running lamps (DRL). Turning the headlamp control to the off position again will turn the automatic headlamps or DRL back on. For vehicles first sold in Canada, the off position only works when the vehicle is shifted into the P (Park) position.
Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada.
Instrument Panel Brightness D (Instrument Panel Brightness): The knob with this symbol on it is located next to the exterior lamps control to the left of the steering wheel. Push the knob in all the way until it extends out and then turn the knob clockwise or counterclockwise to brighten or dim the lights.
Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature continues to work until one of the following occurs: • The ignition is in ON/RUN.
Reading Lamps The vehicle has reading lamps that also act as the dome lamp. Press the button to turn them on and off. Mirror Reading Lamps The vehicle has reading lamps on the rearview mirror. Push the button to turn the reading lamps on and off. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge.
Battery Run-Down Protection This feature helps prevent the battery from being drained, if the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp are accidentally left on. If any of these lamps are left on, they automatically turn off after 10 minutes, if the ignition is off.
Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle and adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the power accessory plugs. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should.
Climate Controls Climate Control System The heating, cooling, defrost, defog and ventilation can be controlled with this system. For vehicles with heated seats, see Heated Seats on page 1-6 . A. Fan Control B. Outside Air C. Recirculation D. Air Delivery Mode Control E.
6 (Floor): Air is directed to the floor outlets, with some of the air directed to the windshield and side window outlets. In this mode, the system automatically selects outside air. - (Defog): This mode clears the windshield of fog or moisture. Air is directed equally to the windshield and the floor outlets.
Using these settings together for long periods of time may cause the air inside the vehicle to become too dry. To prevent this from happening, after the air inside the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so a small amount of water may drip under the vehicle while idling or after turning off the engine.
Outlet Adjustment Use the thumbwheel located below or to the side of the outlet, to change the direction of the air flow. Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the flow of air into the vehicle.
4. Remove the air inlet grille retainers. 5. Lift the air inlet grille and disconnect the washer hose at the quick-connect. 6. Remove the air inlet grille. 7. Remove the water deflector plate. 8. Remove the old passenger compartment air filter. 9. Reverse the steps to install the new air filter.
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel has been used and many other things needed to drive safely and economically.
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven in either miles (used in the United States) or in kilometers (used in Canada).
Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then flashes for several more.
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-65 for important safety information. The instrument panel has a passenger airbag status indicator. When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Charging System Light This light comes on briefly when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. The light should go out once the engine starts.
When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem.
If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes.
Electronic Stability Control Indicator Light This light comes on briefly while the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light will then go off. This light can come on after the vehicle is first driven and the STABILITRAK NOT READY message appears in the Driver Information Center (DIC).
Engine Coolant Temperature Warning Light This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated.
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle.
Oil Pressure Light { CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine.
Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 3-14 for more information. Cruise Control Light The cruise control light comes on whenever the cruise control is set.
Fuel Gage When the ignition is on, the fuel gage indicates about how much fuel is left in the fuel tank. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about. None of these show a problem with the fuel gage: • At the gas station, the gas pump shuts off before the gage reads full.
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located below the speedometer in the instrument panel cluster. The DIC buttons are located on the instrument panel, to the right of the instrument panel cluster.
T (Vehicle Information): Press this button to display the oil life, units, tire pressure readings, compass zone and compass calibration on vehicles with this feature, and Remote Keyless Entry (RKE) transmitter programming. U (Customization): Press this button to customize the feature settings on your vehicle.
If the retro-active reset feature is activated after the vehicle is started, but before it begins moving, the display will show the number of miles (mi) or kilometers (km) that were driven during the last ignition cycle. Fuel Range Press the trip/fuel button until FUEL RANGE displays.
If your vehicle has the Active Fuel Management™ feature, an Active Fuel Management™ indicator will display on the right side of the DIC, while INST ECONOMY displays on the left side. Active Fuel Management™ allows the engine to operate on either all or half of its cylinders, depending on your driving demands.
Remember, you must reset the OIL LIFE yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change.
Relearn Remote Key To access this display, the vehicle must be in P (Park). This display allows you to match the Remote Keyless Entry (RKE) transmitter to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters.
To adjust for compass variance, use the following procedure: Compass Variance (Zone) Procedure 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in P (Park). Press the vehicle information button until PRESS V TO CHANGE COMPASS ZONE displays.
To calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, make sure the compass zone is set to the variance zone in which the vehicle is located. See “Compass Variance (Zone) Procedure” earlier in this section.
AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. See Exterior Lamps on page 3-12 for more information. BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level.
DRIVER DOOR OPEN This message displays when the driver door is not closed properly. Make sure that the door is closed completely. ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature.
ENGINE POWER IS REDUCED This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination.
PASSENGER DOOR OPEN This message displays when the front passenger door is not closed properly. Make sure that the door is closed completely. REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle.
SERVICE BRAKE SYSTEM This message displays when service is required on the brake system. Have the brake system serviced by your dealer/retailer as soon as possible. The brake system warning light also appears on the instrument panel cluster when this message appears on the DIC.
SERVICE TRACTION CONTROL If your vehicle has the Traction Control System (TCS), this message displays when the system is not functioning properly. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-32 .
TIRE LEARNING ACTIVE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the TPMS is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor.
WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer reservoir as soon as possible. See Engine Compartment Overview on page 5-14 for the location of the windshield washer reservoir. Also, see Windshield Washer Fluid on page 5-35 for more information.
DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature.
REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if any of the doors are open.
EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DIC display.
CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: NORMAL: The chime volume will be set to a normal level.
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Setting the Clock Without Date Display AM/FM Base Radio with a Single CD Player This radio has a H button for setting the time. To set the time: 1. Press the H button until the hour begins flashing on display. Press H a second time and the minutes begin flashing on display.
Six-Disc CD (MP3) Player This type of radio has a MENU button instead of the clock button to set the time and date. To set the time and date, follow these instructions: 1. Turn the radio on. 2. Press the MENU button. 3. Once the H option displays, press the pushbutton located under that tab.
Radio(s) The vehicle has one of these radios as its audio system. Radio with CD (Base) Radio with CD (MP3) shown, Radio with Six-Disc CD (MP3) similar 3-66.
Radio Data System (RDS) The radio may have the Radio Data System (RDS) feature. RDS is available for use only on FM stations that broadcast RDS information. This system relies upon receiving specific information from these stations and only works when the information is available.
Finding a Station BAND: Press to switch between FM1, FM2, AM, or XM™. The selection displays. f (Tune): Turn to select radio stations. © SEEK ¨ : Press to go to the previous or the next station and stay there. To scan stations, press and hold either arrow for a few seconds until the radio beeps once.
FAV (Favorites): Press to go through up to six pages of favorites, each having six favorite stations available per page. Each page of favorites can contain any combination of AM, FM, or XM stations. To store a station as a favorite: 1. Tune to the desired radio station.
To return to the manual mode, press until Manual displays or start to manually adjust the bass and depending on the radio, midrange, or treble by pressing the f knob. Adjusting the Speakers (Balance/Fade) ` BAL/FADE (Balance/Fade): To adjust balance or fade, press the ` if the radio has this symbol, or the f knob until the speaker control tabs display.
Undesired XM categories can be removed through the setup menu. To remove an undesired category: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the XM CAT tab. 3. Turn the f knob to display the category to be removed.
Radio Messages for XM™ Only See XM Radio Messages on page 3-81 later in this section for further detail. Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. If the ignition or radio is turned off while a CD in the player it stays in the player.
Z EJECT: For the Radio with a Single CD player, press to eject the CD. If the CD is not removed, after several seconds, the CD automatically pulls back into the player. For the Radio with a Six-Disc CD player, press and release to eject the CD that is currently playing.
To use random on a radio with a Six-Disc CD player: 1. Press the CD/AUX button, press and hold ^ . A beep sounds and Load All Discs displays. Insert one or more discs partway into the slot of the CD player. 2. To play tracks from all CDs loaded in random order, press the pushbutton positioned under the RDM tab until Randomize All Discs displays.
Care of the CD Player Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen. The use of CD lens cleaners for CDs is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD player mechanism.
Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. However, an external audio device such as an iPod, laptop computer, MP3 player, CD changer, or cassette tape player, etc.
Using an MP3 MP3 CD-R or CD-RW Disc The radio may have MP3 capability. With this feature, the radio plays MP3 files that were recorded on a CD-R or CD-RW disc. Song title, artist name, and album can display when files are recorded using ID3 tags version 1 and 2.
• Make sure playlists have a .mp3 or .wpl extension (other file extensions might not work). • Minimize the length of the file, folder or playlist names. Long file, folder, or playlist names, or a combination of a large number of files and folders, or playlists can cause the player to be unable to play up to the maximum number of files, folders, playlists, or sessions.
Order of Play Tracks recorded to the CD-R or CD-RW are played in the following order: • Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the first track of the first playlist.
c T (Next Folder): Press the pushbutton positioned under the Folder tab to go to the first track in the next folder. s REV (Reverse): Press and hold to reverse playback quickly within an MP3 file. Sound is heard at a reduced volume. Release this button to resume playing the file.
songs from the current album begins to play. Once all songs from that album have played, the player moves to the next album in alphabetical order on the CD and begins playing MP3 files from that album. To exit music navigator mode, press the pushbutton below the Back tab to return to normal MP3 playback.
XM Radio ID: If tuned to channel 0, this message alternates with the XM™ Radio 8 digit radio ID label. This label is needed to activate the service. Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer.
Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 3-94 for more information. b g (Push To Talk): Press to answer incoming calls, to confirm system information, and to start speech recognition.
Pairing a Phone 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Pair”. The system responds with instructions and a four digit PIN number.
Linking to a Dif ferent Phone 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Change phone”. The system responds with “Please wait while I search for other phones”.
5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>. Does that sound OK?”. • If the name tag does not sound correct, say “No” and repeat Step 5. • If the name tag sounds correct, say “Yes” and the name tag is stored.
Deleting Name Tags The system uses the following commands to delete name tags: • Delete • Delete all name tags Using the Delete Command The delete command allows specific name tags to be deleted. To use the delete command: 1. Press and hold b g for two seconds.
Making a Call Calls can be made using the following commands: • Dial • Digit Dial • Call • Re-dial Using the Dial Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Dial using <phone name>.
Using the Call Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Call”. The system responds with “Call using <phone name>. Please say the name tag” followed by a tone. 3. Say the name tag of the person to call.
Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press b g to answer an incoming call when another call is active. The original call is placed on hold. • Press b g again to return to the original call.
Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press b g . The system responds with “Ready” followed by a tone.
Sending a Number During a Call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Say a number to send tones” followed by a tone. 3. Say the number to send. • If the system clearly recognizes the number it responds with “OK, Sending Number” and the dial tones are sent and the call continues.
Clearing the System Unless information is deleted out of the in-vehicle Bluetooth system, it will be retained indefinitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name Tags.
Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on the vehicle’s options. Some audio controls can be adjusted at the steering wheel. w (Next): Press to go to the next radio station stored as a favorite, or the next track if a CD is playing.
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Your Driving, the Road, and the Vehicle ........... .4-2 Driving for Better Fuel Economy ...................... .4-2 Defensive Driving .......................................... .4-2 Drunk Driving ................................................ .4-3 Control of a Vehicle .
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops.
Drunk Driving { CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking.
Braking See Brake System Warning Light on page 3-30 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Antilock Brake System (ABS) The vehicle might have the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. If the vehicle has ABS, this warning light on the instrument panel cluster comes on briefly when the vehicle is started.
Braking in Emergencies At some time, nearly every driver gets into a situation that requires hard braking. If the vehicle has ABS, it allows the driver to steer and brake at the same time. However, if the vehicle does not have ABS, the first reaction — to hit the brake pedal hard and hold it down — might be the wrong thing to do.
This light will flash on the instrument panel cluster when the ESC system is both on and activated. You may also feel or hear the system working; this is normal. When the light is on solid and the SERVICE STABILITRAK message is displayed, the system will not assist the driver in maintaining directional control of the vehicle.
If the problem does not clear after restarting the vehicle, you should see your dealer/retailer for service. See DIC Warnings and Messages on page 3-49 for more information. Adding non-dealer/non-retailer accessories can affect your vehicle’s performance.
Turn the system off if the vehicle gets stuck in sand, mud or snow and rocking the vehicle is required. See Rocking Your Vehicle to Get It Out on page 4-20 and If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-19 for more information. To turn the system on or off, press the Traction Control button located on the instrument panel.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Of f-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive.
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water.
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? • Wiper Blades: In good shape? • Fuel, Engine Oil, Other Fluids: All levels checked? • Lamps: Do they all work and are lenses clean? • Tires: Are treads good? Are tires inflated to recommended pressure? • Weather and Maps: Safe to travel? Have up-to-date maps? Highway Hypnosis Always be alert and pay attention to your surroundings while driving.
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission.
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction.
Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-8 .T o get help and keep everyone in the vehicle safe: • Turn on the Hazard Warning Flashers on page 3-6 .
Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gears.
Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will find the label attached below the door lock post (striker). The Tire and Loading Information label lists the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Item Description Total A Maximum Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 7.
Item Description Total A Maximum Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s Tire and Loading Information label for specific information about your vehicle’s maximum vehicle capacity weight and seating positions.
Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. If the vehicle is going to carry a heavy load, spread it out. See “Steps for Determining Correct Load Limit” earlier in this section. { CAUTION: Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 7-8 .
Dinghy Towing Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground. The vehicle was not designed to be towed with all four wheels on the ground.
6. Secure the vehicle to the dolly following the manufacturer’s instructions. 7. Release the parking brake only after the vehicle being towed is firmly attached to the towing vehicle. 8. Turn the ignition to LOCK/OFF and remove the key. Towing a Trailer { CAUTION: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly.
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why the right hitch is needed. Here are some rules to follow: • The rear bumper on the vehicle is not intended for hitches.
Driving with a Trailer Towing a trailer requires a certain amount of experience. Get to know the rig before setting out for the open road. Get acquainted with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself.
Turn Signals When Towing a Trailer The arrows on the instrument panel flash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes or stopping. When towing a trailer, the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out.
Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks.
Service ........................................................... .5-3 Accessories and Modifications ......................... .5-3 California Proposition 65 Warning .................... .5-4 California Perchlorate Materials Requirements .... .5-4 Doing Your Own Service Work .
Tire Pressure Monitor Operation .................... .5-63 Tire Inspection and Rotation .......................... .5-67 When It Is Time for New Tires ...................... .5-68 Buying New Tires ........................................ .5-69 Different Size Tires and Wheels .
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control.
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many fluids, and some component wear by-products contain and/or emit these chemicals.
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 6-15 . Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it.
If the vehicle has the 5.3L V8 engine (VIN Code C), use premium unleaded gasoline with a posted octane rating of 91 or higher. You can also use regular unleaded gasoline rated at 87 octane or higher, but the vehicle’s acceleration could be slightly reduced, and you might notice a slight audible knocking noise, commonly referred to as spark knock.
However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations. To help keep fuel injectors and intake valves clean, or if the vehicle experiences problems due to dirty injectors or valves, look for gasoline that is advertised as TOP TIER Detergent Gasoline.
Fuel E85 (85% Ethanol) The 8th digit of the Vehicle Identification Number (VIN) shows the code letter or number that identifies the vehicle’s engine. The VIN is at the top left of the instrument panel. See Vehicle Identification Number (VIN) on page 5-96 .
If you do switch fuels, it is recommended that you add as much fuel as possible — do not add less than three gallons (11 L) when refueling. You should drive the vehicle immediately after refueling for at least seven miles (11 km) to allow the vehicle to adapt to the change in ethanol concentration.
Filling the Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle.
{ CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { CAUTION: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense fuel only into approved containers.
Hood Release To open the hood, do the following: 1. Pull the interior hood release handle with this symbol on it. It is located to the left of the parking brake pedal. 2. Then go to the front of the vehicle and release the secondary hood latch, located near the center of the hood front, by pushing the latch to the right.
Engine Compartment Overview When you open the hood on the 3.5L V6 engine (3.9L V6 similar), here is what you will see: 5-14.
A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-35 . B. Battery. See Battery on page 5-40 . C. Underhood Fuse Block. See Underhood Fuse Block on page 5-98 . D. Remote Positive (+) Terminal. See Jump Starting on page 5-40 .
When you open the hood on the 5.3L V8 engine, here is what you will see: 5-16.
A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-35 . B. Battery. See Battery on page 5-40 . C. Underhood Fuse Block. See Underhood Fuse Block on page 5-98 . D. Remote Positive (+) Terminal. See Jump Starting on page 5-40 .
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-101 .
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE ENGINE OIL SOON message being turned on, reset the system.
When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 6-4 for more information.
2. Push the filter cover housing toward the engine. 3. Pull out the filter. 4. Inspect or replace the engine air cleaner/filter. 5. To reinstall the cover, position the tabs through the hinges on the housing. 6. Push the cover tabs on top of the housing to lock the cover in place.
Automatic Transmission Fluid When to Check and Change Automatic Transmission Fluid A good time to check your automatic transmission fluid level is when the engine oil is changed. Change the fluid and filter at the intervals listed in Additional Required Services on page 6-6 , and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 6-12 .
Then, without shutting off the engine, follow these steps: 1. Pull out the dipstick and wipe it with a clean rag or paper towel. The transmission fluid dipstick handle is the black loop with this symbol on it. It is located near the rear of the engine compartment.
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See Recommended Fluids and Lubricants on page 6-12 . If the fluid level is low, add only enough of the proper fluid to bring the level into the cross-hatched area on the dipstick.
A. Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Engine Coolant The cooling system in the vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down.
How to Add Coolant to the Radiator { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
4. Then fill the coolant recovery tank to the COLD FILL line. 5. Install the coolant recovery tank cap and the pressure cap. After a day or two of driving, when the engine is cold, check the coolant level in the recovery tank. If it is low, refill it to the COLD FILL line.
If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced.
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: • Climbs a long hill on a hot day.
Overheated Engine Protection Operating Mode This emergency operating mode allows your vehicle to be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage.
How to Check Power Steering Fluid To check the power steering fluid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Adding Washer Fluid A WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC) when you need to add windshield washer fluid to your vehicle. See DIC Warnings and Messages on page 3-49 for more information. Open the cap with the washer symbol on it.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 5-14 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear.
What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 6-12 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts.
{ CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles.
{ CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
7. Do not let the other end touch metal. Connect it to the positive (+) terminal location of the vehicle with the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( − ) cable to the negative ( − ) terminal location of the vehicle with the good battery.
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery.
Headlamps, Front Turn Signal, Sidemarker, and Parking Lamps A. Sidemarker B. Low-Beam Headlamp C. High-Beam Headlamp D. Parking/Turn Signal Lamp To replace one of these bulbs: 1. Open the hood. See Hood Release on page 5-13 . 2. Remove the screw from the headlamp assembly.
3. Pull up on the plastic headlamp retainer and remove it. 4. Pull the headlamp assembly away from the vehicle and remove the electrical connector. 5. Remove the round dust caps to gain access to the bulbs. 6. Turn the old bulb counterclockwise and remove it from the retaining ring by pulling it away from the headlamp.
12. Push down on the plastic headlamp retainer to reinstall it. 13. Reinstall the screw from the headlamp assembly. 5-48.
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps A. Rear Sidemarker Lamp B. Back-up Lamp C. Stoplamp/Taillamp/Turn Signal To replace one of these bulbs: 1. Open the trunk. See Trunk on page 2-12 . 2. Remove the convenience net. Unhook the net from the upper wing nut.
5. Turn the two hex nuts counterclockwise to remove them. 6. Pull out the taillamp assembly and disconnect the wiring harness. 7. Turn the bulb socket counterclockwise to remove it. 8. Pull the old bulb straight out to remove it. 9. Push the new bulb straight in until it clicks to install it.
License Plate Lamp To replace one of these bulbs: 1. Turn the lamp assembly counterclockwise and pull the lamp assembly out of the connector. 2. Pull the old bulb from the lamp assembly, keeping the bulb straight as you pull it out. 3. Install the new bulb.
To remove and replace the wiper blade element do the following: 1. The wiper blade element has two notches at one end which are engaged by the bottom claw set of the wiper blade. At the notched end of the wiper blade, pull the wiper blade element from the wiper blade assembly.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type, and service description.
(D) Tire Identification Number (TIN) : The letters and numbers following DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
(B) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN).
(C) Aspect Ratio : A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide.
Cold Tire Pressure : The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inflation - Tire Pressure on page 5-60 . Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo.
Maximum Loaded Vehicle Weight : The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight : The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-20 .
UTQGS (Uniform Tire Quality Grading Standards) : A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.
A vehicle specific Tire and Loading Information label is attached to your vehicle. This label shows your vehicle’s original equipment tires and the correct inflation pressures for your tires when they are cold. The recommended cold tire inflation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle.
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
Using the DIC, tire pressure levels can be viewed by the driver. For additional information and details about the DIC operation and displays see DIC Operation and Displays on page 3-42 and DIC Warnings and Messages on page 3-49 . The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as you start to drive.
• One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/retailer for service. • Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels.
You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 5-68 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-63 . Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 5-101 . { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Dif ferent Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Used Replacement Wheels { CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
CAUTION: (Continued) Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust, or remove the device if it is contacting your vehicle, and do not spin your wheels.
A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go.
CAUTION: (Continued) To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle. When the vehicle has a flat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A).
6. Turn the nut holding the jack counterclockwise and remove it. Then remove the jack and wrench. The tools you will need to change a tire include the jack (A), extension and protection guide (B), and wheel wrench (C).
Removing the Flat Tire and Installing the Spare Tire This vehicle may have aluminum wheels with exposed wheel nuts. Use the wheel wrench to loosen all the wheel nuts. Do not remove them yet. Or, this vehicle may have steel wheels with plastic covers. To remove the plastic covers and wheel nut caps, loosen the plastic nut caps with the wheel wrench in a counterclockwise direction.
3. For all wheel types, find the jacking location using the diagram above and the corresponding jacking notches located on the bottom side of the plastic molding. The notches in the plastic molding are marked with a triangle shape to help you find them.
{ CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
{ CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
9. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut clockwise by hand until the wheel is held against the hub.
{ CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
A. Cover B. Retainer C. Compact Spare Tire D. Wing Nut E. Jack F. Wheel Wrench G. Extension Protector H. Foam Holder I. Bolt Screw Compact Spare Tire 5-86.
A. Retainer B. Full-Size Flat Tire C. Protective Guide D. Extension Bolt Screw E. Wing Nut F. Jack G. Wheel Wrench H. Foam Holder I. Bolt Screw Full-Size Flat Tire 5-87.
Compact Spare Tire { CAUTION: Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time. Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time.
Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces.
Products that remove odors from the vehicle’s upholstery and clean the vehicle’s glass can be obtained from your dealer/retailer. Do not clean the vehicle using: • A knife or any other sharp object to remove a soil from any interior surface. • A stiff brush.
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface.
Care of Safety Belts Keep belts clean and dry. { CAUTION: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Weatherstrips If dirt and/or contaminants build up in the glass seals, use a cloth and water to clean the glass seals.
Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle.
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle.
Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have the headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a fuse.
Fuses Usage AIRBAG Airbags AMP Amplifier AUX Auxiliary Outlets CNSTR Canister DR/LCK Door Locks HTD/SEAT Heated Seats Fuses Usage PWR/MIR Power Mirrors PWR/SEAT Power Seats PWR/WNDW Power Window RAP Retained Accessory Power S/ROOF Sunroof TRUNK Trunk TRUNK Trunk Relay XM XM™ Radio Underhood Fuse Block The underhood fuse block is located in the engine compartment.
Fuses Usage A/C CMPRSR Air Conditioning Compressor ABS MTR 1 Antilock Brake System (ABS) Motor 1 ABS MTR 2 ABS Motor 2 AIR PUMP Air Pump AIR SOL Air Injection Reactor Solenoid AIRBAG/ DISPLAY Airbag, .
Fuses Usage ETC/ECM Electronic Throttle Control, ECM FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FOG LAMPS Fog Lamps (If Equipped) FUEL/PUMP Fuel Pump HDLP MDL Headlamp Module HORN Horn HTD MIR Heated Mir.
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood.
Application Capacities English Metric Fuel Tank 3.5L Engine (with NU6 emissions) 17.0 gal 64.4 L 3.5L Engine (without NU6 emissions) 17.5 gal 66.2 L 3.9L and 5.3L 17.5 gal 66.2 L Wheel Nut Torque 100 lb ft 140 Y All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual.
Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using the Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details.
Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather.
The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Maintenance Replacement Parts on page 6-13 . When the vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 5-17 . Reset oil life system. See Engine Oil Life System on page 5-20 . An Emission Control Service. •• Visually check for any leaks or damage.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect fuel system for damage or leaks.
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life.
(h) Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traff ic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain.
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL ® coolant mixture if necessary. See Engine Coolant on page 5-28 . Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary.
Automatic Transmission Shift Lock Control System Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Parking Brake and Automatic Transmission P (Park) Mechanism Check { CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Maintenance Replacement Parts Part GM Part Number AC Delco Part Number Engine Air Cleaner/Filter 10350737 A2962C Engine Oil Filter 3.
Engine Drive Belt Routing 3.5L V6 and 3.9 V6 Engines 5.3L V8 Engine 6-14.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 . Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-16.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-17.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-18.
Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-5 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments.
STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/ Arbitration Program.
Online Owner Center Online Owner Center (U.S.) — www.gmownercenter.com/chevrolet Information and services customized for your specific vehicle — all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Chevrolet dealers for service nationwide • Exclusive privileges and offers • Recall notices for your specific vehicle • OnStar ® and GM Cardmember Services Earnings summaries Other Helpful Links: Chevrolet — www.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center. Any TTY user in the U.
Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.
Roadside Assistance Program For U.S. purchased vehicles, call 1-800-CHEV-USA (1-800-243-8872); (Text telephone (TTY): 1-888-889-2438) . For Canadian purchased vehicles, call 1-800-268-6800 .
Services Provided • Emergency Fuel Delivery: Delivery of enough fuel for the vehicle to get to the nearest service station. • Lock-Out Service: Service is provided to unlock the vehicle if you are locked out. A remote unlock may be available if you have OnStar ® .
• Trip Interruption Benefits and Assistance: Must be over 250 kilometres from where your trip was started to qualify. General Motors of Canada Limited requires pre-authorization, original detailed receipts, and a copy of the repair orders. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment.
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended powertrain, and hybrid specific warranty in both the U.
Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer’s shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service.
Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built. Genuine GM Collision parts are your best choice to ensure that your vehicle’s designed appearance, durability, and safety are preserved.
Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
• Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identification Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traff ic Safety Administration (NHTSA) in addition to notifying General Motors.
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks.
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
✍ NOTES 7-20.
A Accessories and Modifications ............................ 5 - 3 Accessory Power ............................................ 2-21 Accessory Power Outlets ................................. 3-18 Active Fuel Management™ ............................
Ashtray ......................................................... 3-19 Assistance Program, Roadside ........................... 7 - 8 Audio System ................................................. 3-63 Audio Steering Wheel Controls ...................
Canadian Owners ................................................ i i Capacities and Specifications .......................... 5-101 Carbon Monoxide Engine Exhaust ........................................... 2-30 T runk ...............................
Cooling System .............................................. 5-26 Courtesy Lamps ............................................. 3-15 Courtesy T ransportation ................................... 7-11 Cruise Control .....................................
E E85 Fuel ......................................................... 5 - 8 E D R ............................................................. 7-18 Electrical Equipment Add-On Equipment ...................................... 5-96 Electrical System Fuses and Circuit Breakers .
Fuel ............................................................... 5 - 5 Additives ...................................................... 5 - 6 California Fuel .............................................. 5 - 6 E85 (85% Ethanol) ..................
Highway Hypnosis ........................................... 4-15 Hill and Mountain Roads .................................. 4-16 Hood Checking Things Under ................................ 5-12 Release ................................................
Lights (cont.) F o g L a m p .................................................. 3-40 Highbeam On ............................................. 3-40 High/Low Beam Changer ................................ 3 - 8 Oil Pressure .............................
Mirrors Automatic Dimming Rearview ........................ 2-32 Manual Rearview Mirror ................................ 2-32 Outside Convex Mirror ................................. 2-33 Outside Heated Mirrors ................................ 2-33 Outside Power Mirrors .
Perchlorate Materials Requirements, California ...... 5 - 4 Phone Bluetooth ® .................................................. 3-82 Power Door Locks ................................................. 2-10 Electrical System ..........................
Ride Control Systems ....................................... 4 - 6 Electronic Stability (ESC) ................................ 4 - 6 Roadside Assistance Program ............................ 7 - 8 Rocking Y our V ehicle to Get it Out ..................
Shifting Into Park ............................................ 2-27 Signals, T urn and Lane-Change .......................... 3 - 7 Spare T ire Compact .................................................... 5-88 Installing .............................
Tires (cont.) Inflation - T ire Pressure ................................ 5-60 Inspection and Rotation ................................ 5-67 Installing the Spare T ire ................................ 5-79 Pressure Monitor Operation .................
W W arning Lights, Gages, and Indicators ............... 3-24 W arnings DIC W arnings and Messages ........................ 3-49 Hazard W arning Flashers ............................... 3 - 6 Safety and Symbols ........................................
デバイスChevrolet 2009 Impalaの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chevrolet 2009 Impalaをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChevrolet 2009 Impalaの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chevrolet 2009 Impalaの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chevrolet 2009 Impalaで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chevrolet 2009 Impalaを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChevrolet 2009 Impalaの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chevrolet 2009 Impalaに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChevrolet 2009 Impalaデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
